GSG GTH 2448/1 Manuale utente
E26.0.e1-1-7 Blatt 1 von 2
Operating Manual for Digital Thermometer
GTH 2448/1
Temperature Display
-50 -46
-40 -37
-30 -28
-20 -19
-10 -10
0 0
10 10
20 20
30 29
40 39
50 49
60 59
70 70
80 80
90 90
100 100
110 110
120 120
130 130
140 140
150 150
Temperature Display
580 587
590 597
600 607
610 618
620 628
630 639
640 649
650 659
660 670
670 680
680 690
690 700
700 711
710 721
720 731
730 741
740 751
750 762
760 772
770 782
780 792
Temperature Display
790 802
800 812
810 822
820 832
830 842
840 852
850 862
860 871
870 881
880 891
890 901
900 911
910 920
920 930
930 940
940 949
950 959
960 969
970 978
980 988
990 997
Temperature Display
1000 1007
1010 1016
1020 1026
1030 1035
1040 1045
1050 1054
1060 1063
1070 1073
1080 1082
1090 1091
1100 1100
1110 1110
1120 1119
1130 1128
1140 1137
1150 1146
1160 1155
1170 1164
1180 1173
C o r r e c t i o n t a b l e :
Temperature Display
370 369
380 379
390 390
400 400
410 410
420 421
430 431
440 441
450 452
460 462
470 472
480 483
490 493
500 504
510 514
520 524
530 535
540 545
550 556
560 566
570 576
Temperature Display
160 160
170 169
180 179
190 189
200 198
210 208
220 218
230 228
240 238
250 248
260 258
270 268
280 278
290 288
300 298
310 308
320 318
330 328
340 339
350 349
360 359
Specification:
Measuring range: -50...+1150°C
Resolution: 1°C
Probeconnection: NiCr-Ni, (probe not included in scope of supply)
Accuracy: <1%±1 Digit (from -20 to +550°C and 920 to 1150°C); <1.5% ±1Digitfrom 550...920°C.
Formore detailed values please refer to att. correction table.
Display: 3½-digit, red LED-display, 10 mm high
Scan rate: approx. 3 measurements/sec.
Nominal temperature: 25°C
Working temperature: 0to50°C
Relative humidity: 5 to 95 % r.h. (non-condensing)
Storage temperature: -20 to 85°C
Voltage supply: 12VDC (8 - 20VDC) or 24VDC (18 - 29VDC) (to be set via soldering jumper)
Power consumption: max. 30 mA
Housing: glassfibrereinforcedNoryl,frontscreenPC.
Dimensions: 24 x 48 mm (H x W) (dimensions of front frame)
Mounting depth: approx. 65 mm (incl. screw-type/plug-in terminals)
Panel mounting: by means of VA- elastic spike, allowed panel thickness: from 1 to approx. 10 mm
Panel cut-out: 21.7+0.5 x 45+0.5 mm (H x W).
Connection terminals: 4-pinscrew-type/plug-in terminals for wire dias ranging from 0.14 to 1.5 mm²
EMC: Unithasbeen tested according to EN50081-1andEN50082-2
additional fault: <1%
IP rating: frontIP54 (with optional O-rings IP65).
E26.0.e1-1-7 Blatt 2 von 2
Accessories: (small selection - for our complete accessories refer to our catalogue)
GNG220/1-12V power supply (230VAC) for GIA2448 input: 230VAC; output: 12VDC stabilised, max. 40mA
IP65 SET O-rings O-ringsfor IP rating IP65 at the front (2 pcs.)
GTF101-5/15150 Immersion probe -220...+1150°C Immersionprobefor highest temperatures.
(Stainless steel probe tube, flexible, cable lenght approx. 1m,
probe lenght 150mm, dia 1.5mm -outerconfigurationrefercatalogue)
GTF 300 - AdH Wire probe -65...+300°C Probeforquick-response measurements in liquids, gases and for
small surfaces (probe lenght approx. 1m).
GMF 250 - AdH Surface probe -65...+250°C Magnetic surface probe, sticks of magnetic materials
(probewithapprox. 1m cable)
When ordering standard probes (offered in catalogue with NiCr-Ni-plug), append "- AdH" or"no plug" tothetypename!
soldering jumper A1
Elektrischer Anschluß:
Electric connections for the GTH 2448 / 1 are located at the back of the unit.
Connection is made via screw-type/plug-in terminals (max. terminal range 1,5mm²).
Makeitaruleto always mount screw-type/plug-in terminals while they are still looseandconnectonlylater.
Ifterminalsaremounted after connection there is a riskthatsolderingeyesmaycomeloose. Please use suitable
screw-driveranddonottightenscrewsbyforce.
Supplyvoltage: 12VDC or 24VDC
Terminal assignment: +Uv = supply voltage +
GND = supply voltage -
Pleasemakesureto check if supply voltage and voltage range set
conformtoeachother.
Usethesolderingjumpernextto the connection terminal to select
supplyvoltage:
Jumper "A1" open: 24 V DC ( 18 - 29 V DC )
Jumper "A1" closed: 12 V DC ( 8 - 20 V DC)
Probeconnection: NiCr-Ni (type K)
Boththeconnectionand commissioning of the unit must only be carried
out by skilled personnel. In case of a wrong connection, the unit may be
destroyed-no warranty claims can beaccepted!
Safety regulations
Makeitaruletoalwaysobserve the following points to exclude any risk whatsoever for the operator.
a) In case of any obvious damage and/or functional problems disconnect unit immediately
b) Prior to opening it, disconnect unit and supply voltage source. Make sure that all parts of the unit are protected against direct
touching when mounting the unit and setting its connections.
c) Please always adhere to the standard safety regulations for electric devices, power systems and light-current installations,
and make sure that your national safety regulations (e.g. VDE 0100) are observed.
d) If unit is to be connected to other devices (e.g. via serial interface) the circuitry has to be designed most carefully. Internal
connection in third party units may result in not-permissible voltages.
Skilled personnel
These are persons who are familiar with the installation, mounting, commissioning and the operation of the product and have
acquired a qualification for their job:
nTraining or instructions or qualification to switch on/off, isolate, ground and apply markings to circuits and devices/systems
in accordance with the latest state of the art standards of safety technology.
nTraining or instructions regarding the proper care and use of suitable safety equipment in accordance with the latest state of
the art standards of safety technology.
nFirst aid training.
Warning: When operating electric devices parts of these devices will, as a matter of course, be live.
Unless the warnings are observed severe damage to life and limb or to property may be the
result. Make sure that only skilled personnel is working with this device. Trouble-free
operation of this device can only be guaranteed if it is properly transported and stored.
Carefull installation, mounting, operation and maintenance are vital factors for the safe
operation of this device.
Altri manuali GSG Termometro
