Gyration CYBERVIEW 410T-TAA Manuale utente
Quick Start Guide
CYBERVIEW 410T-TAA
4 MP Outdoor Intelligent Fixed Turret Camera
Other Language
www.gyration.com
1
Waterproof Requirements
Please waterproof cables in accordance with the following instructions. User shall
assume all responsibility for device damage caused by water due to improper
waterproof measures.
NOTE!
⚫Before you start, connect all the needed cables and cut off the copper wires for
the cables that you don't use.
⚫Please use self-adhesive waterproof tape (supplied with some products) to
protect the cables.
⚫Use waterproof components to protect the network cable. Waterproof the
power cable separately if you don’t use it. The video cable does not need
waterproof treatment.
1. Use insulation tape (not included in the package) to insulate the connection part
of each cable.
2. Waterproof the cables with self-adhesive waterproof tape.
(1) Fully stretch the waterproof tape at both ends.
(2) Wrap the connection part and the cable ends tightly with waterproof tape.
Make sure the tape is fully stretched during the process.
(3) Tighten the tape at both ends to prevent water leakage.
Connection part
Insulation tape
2
3. Install the supplied waterproof components to the network cable in sequence.
CAUTION!
You need to mount the rubber ring onto the network cable interface first.
4. If your camera has a DC cable and you will not use it, insert the plug into the
interface.
5. (Optional) After the waterproof treatment is completed, put the cables into a
waterproof junction box (purchased separately).
CAUTION!
⚫The cable connector must not be exposed and must be kept away from water.
⚫Restore and fasten the device after dismounting.
⚫Place the power adapter in a power distribution box.
Wrap the unused cables together into a bundle
Tighten Tighten
Waterproof tape
Tighten
DC interface
Plug
3
1Packing List
Contact your local dealer if the package is damaged or incomplete. The attachments
may vary with models, please see the actual model for details.
No.
Name
Qty
Unit
1
Camera
1
PCS
2*
Waterproof components（1）
1
Set
3*
Screw components（2）
1
Set
4*
Mount accessory（3）
1
Set
5
User manual
1
Set
Remarks:
* means optional and supplied with certain models only.
(1)Including one or more waterproof components such as tape and plug.
(2)Including one or more accessories such as screws and hex key.
(3)Including one or more items from drilling template, bracket adapter, anti-static
gloves, etc.
2Safety Instructions
Installation and removal of the unit and its accessories must be carried out by
qualified personnel. You must read all of the safety instructions before installation
and operation.
2.1 Precautions
⚫Use a power adapter or a PoE device that meets requirements. Otherwise, the
device may be damaged.
⚫Be careful not to blur, scratch, damage the dome cover or leave fingerprints on
it because this could decrease image quality. Keep the protective film on the
dome cover until installation is complete.
⚫Make sure the length of the power cable between the power adapter and the
camera is not too long, otherwise the voltage of the camera is lowered, causing
the camera to work abnormally. If it is required to lengthen the power cable,
lengthen the cable between the power adapter and the mains.
4
⚫Do not overbend the cables during the installation, otherwise, poor cable contact
may cause malfunction.
⚫When connecting to an external interface, use an existing connection terminal,
and ensure that the cable terminal (latch or clamp) is in good condition and
properly fastened. Ensure that the cable is not tense during mounting, with a
proper margin reserved to avoid poor port contact or loosening caused by shock
or shake.
⚫During transportation, special attention is required to protect the transparent
dome cover from friction, scratch and stain, etc. Do not remove the protective
film from the cover until mounting is finished. Remove the protective film before
powering on the device.
⚫Make sure the wall or ceiling is strong enough to support the weight of the
camera. If dust falls during mounting, take off the dome cover and keep it away
from dust. Install the dome cover after the base is installed.
⚫Contact professionals for maintenance information. Do not attempt to dismantle
the device by yourself. We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.
2.2 Maintenance
⚫If there is dust on the front glass surface, remove the dust gently using an oil-
free brush or a rubber dust blowing ball.
⚫If there is grease or a dust stain on the front glass surface, clean the glass surface
gently from the center outward using anti-static gloves or an oil-free cloth. If the
grease or the stain still remains, use anti-static gloves or an oil-free cloth dipped
with detergent and clean the glass surface gently until it is clean.
⚫Do not use organic solvents (such as benzene and alcohol) to clean the
transparent dome cover.
3Appearance
3.1 Dimensions
The following figure shows device dimensions. The appearance may vary with device
model.
Type A
5
Type B
3.2 Cable Connection
The appearance and tail cable may vary with device model.
95.93mm
3.8"
118.08mm
4.6"
95.93mm
3.8"
118.08mm
4.6"
1
2
3
4
IP
Network
5
6
6
1. Base plate
2. Housing
3. Lens
4. Infrared LED
5. Power interface(12 VDC)
6. Ethernet interface
4Mount Your Camera
You can adopt ceiling mount or wall mount and purchase hardware accessories by
yourself. The following part takes ceiling mount as an example. Wall mount is similar
to ceiling mount and therefore is omitted here.
1. Attach the sticker to ceiling, and then drill 30-mm deep guide holes using a drill
bit (6mm or 6.5mm in diameter) according to the sticker.
2. Insert the plastic anchors.
(1) Drill a hole to lead cables out of the ceiling.
(2) Knock in plugs.
3. Detach the housing from the base plate with the marks aligned.
2
1
7
4. Install the base plate and the camera. Connect cable and protect it with
waterproof tape and attach dome to ceiling with taping screws.
5. Mount your camera. Mount the housing with install mark aligne.
Install mark
Install mark
slot
Install mark
Install mark
8
6. Adjust the monitoring direction. Rotate the camera to desired monitoring
direction.
The above steps are for concealed installation. For an open installation, lead the
cables from the open slot on the base plate.
NOTE!
When you adopt open installation, make sure that the cables can be led out
through the open slot on the base plate and screw the dome to the wall as shown
in step 3.
5Startup
After you have installed the device, connect one end of the power adapter
(purchased separately) to power supply, and then connect the other end to the
power interface to start up the device.
6Access Your Camera
1. Open your Web browser, enter the camera's IP address in the address bar, and
then press Enter. The default IP is 192.168.1.13.
1
2
9
2. In the login page, enter the default username and password (admin/123456),
then click Login.
NOTE!
⚫DHCP is enabled by default. If a DHCP server is used in your network, your
camera may be assigned an IP address, and you need to use the assigned IP
address to log in.
⚫You may need to install a plug-in at your first login. Please follow the on-screen
instructions to complete the installation and then open the browser again to
log in.
⚫The default password is intended only for your first login. To ensure security,
please change the password after your first login. You are strongly
recommended to set a strong password of at least nine characters including all
three elements: digits, letters and special characters.
⚫If the password has been changed, please use the new password to log in.
Indice
Altri manuali Gyration Telecamera di sicurezza
Gyration
Gyration Cyberview2010 Manuale utente
Gyration
Gyration CYBERVIEW 200B Manuale utente
Gyration
Gyration CYBERVIEW 411B-TAA Manuale utente
Gyration
Gyration CYBERVIEW 410B-TAA Manuale utente
Gyration
Gyration Cyberview3010 Manuale utente
Gyration
Gyration CYBERVIEW 410D-TAA Manuale utente
Gyration
Gyration Cyberview2000 Manuale utente
Gyration
Gyration CYBERVIEW 411T-TAA Manuale utente
Gyration
Gyration CYBERVIEW 411D-TAA Manuale utente
