H3C S3100 Series Istruzioni per l'installazione

H3C S3100 Series Ethernet Switches

Command Manual (For Soliton)

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: 20080928-C-1.02

No part of this manual may be reproduced or transmitted in any form or by any means

without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H3Care,

, TOP G, , IRF, NetPilot,

Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,

Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and

HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their

respective owners.

Notice

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents, but

all statements, information, and recommendations in this document do not constitute

the warranty of any kind, express or implied.

To obtain the latest information, please access:

http://www. h3c.com

Technical Support

customer_service@h3c.com

http://www. h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S3100 Series Ethernet Switches documentation

set includes the following:

Manual Description

H3C S3100 Series Ethernet Switches

Installation Manual (For Soliton)

It is used for assisting the users in switch

installation, booting up, hardware and

software maintenance.

H3C S3100 Series Ethernet Switches

Operation Manual (For Soliton) It is used for assisting the users in data

configurations and typical applications.

H3C S3100 Series Ethernet Switches

Quick Start (For Soliton) It provides information for the system

installation.

Organization

H3C S3100 Series Ethernet Switches Command Manual (For Soliton) is organized as

follows:

Part Contents

1 CLI Introduces the commands used for switching

between the command levels and command level

setting.

2 Login Introduces the commands used for logging into the

Ethernet switch.

3 Configuration File

Management Introduces the commands used for configuration

file management.

4 VLAN Introduces the commands used for configuring

VLAN.

5 Management VLAN Introduces the commands used for configuring the

management VLAN.

6 IP Address-IP Performance Introduces the commands used for IP address

configuration and IP performance configuration.

7 Voice VLAN Introduces the commands used for voice VLAN

configuration.

8 GVRP Introduces the commands used for GVRP

configuration.

Part Contents

9 Port Basic Configuration Introduces the commands used for basic port

configuration.

10 Link Aggregation Introduces the commands used for link

aggregation.

11 Port Isolation Introduces the commands used for port isolation.

12 Port Security-Port Binding Introduces the commands used for port security

configuration and port binding.

13 DLDP Introduces the commands used for DLDP

configuration.

14 MAC Address Table

Management Introduces the commands used for MAC address

forwarding table management.

15 MSTP Introduces the STP-related commands.

16 Multicast Introduces the commands used for multicast

configuration.

17 802.1x-System Guard Introduces the commands used for 802.1x-System

Guard configuration.

18 AAA Introduces the commands used for AAA, RADIUS,

HWTACACS, and EAD configuration.

19 MAC Address

Authentication Introduces the commands used for MAC address

authentication configuration.

20 ARP Introduces the ARP-related commands.

21 DHCP Introduces the commands used for DHCP,

DHCP-snooping configuration.

22 ACL Introduces the ACL-related commands.

23 QoS-QoS Profile Introduces the commands used for QoS and QoS

profile configuration.

24 Mirroring Introduces the commands used for port mirroring.

25 Stack-Cluster Introduces the commands used for cluster

management.

26 SNMP-RMON Introduces the commands used for SNMP and

RMON configuration.

27 NTP Introduces the NTP-related commands.

28 SSH Introduces the commands used for SSH

configuration.

29 File System Management Introduces the commands used for file system

management.

30 FTP-SFTP-TFTP Introduces the FTP-/SFTP-/TFTP-related

commands.

Part Contents

31 Information Center Introduces the commands used for information

center configuration.

32 System Maintenance and

Debugging Introduces the commands used for system

maintenance and debugging.

33 VLAN-VPN Introduces the commands used for VLAN VPN

configuration.

34 HWPing Introduces the commands used for HWPing

configuration.

35 IPv6 Management Introduces the commands used for IPv6

Management configuration.

36 DNS Introduces the commands used for DNS

configuration.

37 Smart Link-Monitor Link Introduces the commands used for Smart Link,

Monitor Link configuration

38 Appendix

Lists all the commands described in this command

manual in an alphabetic order. The parts and

pages where the commands are described are

also given.

Conventions

The manual uses the following conventions:

I. Command conventions

Convention Description

Boldface The keywords of a command line are in Boldface.

italic Command arguments are in italic.

[ ] Items (keywords or arguments) in square brackets [ ] are

optional.

{ x | y | ... }

Alternative items are grouped in braces and separated by

vertical bars. One is selected.

[ x | y | ... ]

Optional alternative items are grouped in square brackets

and separated by vertical bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces and separated by

vertical bars. A minimum of one or a maximum of all can be

selected.

[ x | y | ... ] *

Optional alternative items are grouped in square brackets

and separated by vertical bars. Many or none can be

selected.

Convention Description

&<1-n> The argument(s) before the ampersand (&) sign can be

entered 1 to n times.

# A line starting with the # sign is comments.

II. GUI conventions

Convention Description

< > Button names are inside angle brackets. For example, click

<OK>.

[ ] Window names, menu items, data table and field names

are inside square brackets. For example, pop up the [New

User] window.

/ Multi-level menus are separated by forward slashes. For

example, [File/Create/Folder].

III. Symbols

Convention Description

Warning Means reader be extremely careful. Improper operation

may cause bodily injury.

Caution Means reader be careful. Improper operation may cause

data loss or damage to equipment.

Note Means a complementary description.

Command Manual (For Soliton) – CLI

H3C S3100 Series Ethernet Switches Table of Contents

Table of Contents

Chapter 1 CLI Configuration Commands.................................................................................... 1-1

1.1 CLI Configuration Commands ...........................................................................................1-1

1.1.1 command-privilege level .........................................................................................1-1

1.1.2 display history-command ........................................................................................1-3

1.1.3 super .......................................................................................................................1-4

1.1.4 super authentication-mode......................................................................................1-5

1.1.5 super password.......................................................................................................1-6

Command Manual (For Soliton) – CLI

H3C S3100 Series Ethernet Switches Chapter 1 CLI Configuration Commands

1-1

Chapter 1 CLI Configuration Commands

1.1 CLI Configuration Commands

1.1.1 command-privilege level

Syntax

command-privilege level level view view command

undo command-privilege view view command

View

System view

Parameters

level level: Command level to be set, in the range of 0 to 3.

view view: CLI view. It can be any CLI view that the Ethernet switch supports. The

S3100 series (For Soliton) support only the CLI views listed in Table 1-1:

Table 1-1 Available CLI views for the view argument

CLI view Description

acl-adv Advanced ACL view

acl-basic Basic ACL view

acl-ethernetframe Layer 2 ACL view

aux Aux 1/0/0 port view, that is, console port view

cluster Cluster view

ethernet 100M Ethernet port view

ftp-client FTP client view

gigabitethernet GigabitEthernet port view

gqinq QinQ view

hwping HWPing test group view

hwtacacs HWTACACS view

isp ISP domain view

loopback Loopback interface view

luser Local user view

manage-vlan Management VLAN view

Command Manual (For Soliton) – CLI

H3C S3100 Series Ethernet Switches Chapter 1 CLI Configuration Commands

1-2

CLI view Description

mst-region MST region view

mtlk-group Monitor link group view

null NULL interface view

peer-key-code Public key editing view

peer-public-key Public key view

poe-profile PoE profile view

qos-profile QoS profile view

radius-template RADIUS scheme view

shell User view

smlk-group Smart link group view

system System view

user-interface User interface view

vlan VLAN view

vlan-interface VLAN interface view

command: Command for which the level is to be set.

Description

Use the command-privilege level command to set the level of a specified command in

a specified view.

Use the undo command-privilege view command to restore the default.

Commands fall into four levels: visit (level 0), monitor (level 1), system (level 2), and

manage (level 3). The administrator can change the level of a command as required.

For example, the administrator can change a command from a higher level to a lower

level so that the lower level users can use the command.

The default levels of commands are described in the following table:

Table 1-2 Default levels of commands

Level Name Command

0 Visit level Commands used to diagnose network, such as ping,

tracert, and telnet commands.

1 Monitor level

Commands used to maintain the system and diagnose

service fault, such as debugging, terminal and reset

commands.

2 System level

All configuration commands except for those at the

manage level.

Command Manual (For Soliton) – CLI

H3C S3100 Series Ethernet Switches Chapter 1 CLI Configuration Commands

1-3

Level Name Command

3 Manage level

Commands associated with the basic operation modules

and support modules of the system, such as file system,

FTP/TFTP/XMODEM downloading, user management,

and level setting commands.

Examples

# Set the level of the system-view command in user view (shell) to 0.

<Sysname> system-view

System View: return to User View with Ctrl+Z.

[Sysname] command-privilege level 0 view shell system-view

1.1.2 display history-command

Syntax

display history-command

View

Any view

Parameters

None

Description

Use the display history-command command to display the history commands of the

current user, so that the user can check the configurations performed formerly.

History commands are those commands that was successfully executed recently and

saved in the history command buffer. You can set the size of the buffer by the

history-command max-size command. When the history command buffer is full, the

earlier commands will be overwritten by the new ones.

By default, the CLI can save 10 history commands for each user.

Related commands: history-command max-size in login module.

Examples

# Display the history commands of the current user.

<Sysname> display history-command

system-view

quit

display history-command

Altri manuali per S3100 Series

Indice

Altri manuali H3C Interruttore

H3C

H3C S10500X-G Series Manuale del proprietario

H3C

H3C S10500X Series Manuale utente

H3C

H3C S5500-SI Series Manuale utente

H3C

H3C S5820 series Manuale di installazione

H3C

H3C S5560S-EI Series Manuale utente

H3C

H3C S9825 Series Manuale utente

H3C

H3C S6300 Series Manuale utente

H3C

H3C S9500E Series Manuale utente

H3C

H3C S6820 Series Manuale utente

H3C

H3C S3100-52P Manuale utente

H3C

H3C S10506 Manuale operativo e di manutenzione

H3C

H3C Magic BS200 GE Series Manuale utente

H3C

H3C S5500-SI Series Manuale utente

H3C

H3C S7500 Series Manuale utente

H3C

H3C H3C S3600 Series Manuale utente

H3C

H3C S5500-SI Series Manuale utente

H3C

H3C s5800 series Manuale utente

H3C

H3C S3100 Series Manuale utente

H3C

H3C S6800-2C-FC Manuale operativo e di manutenzione

H3C

H3C S12500 Series Guida rapida

H3C

H3C S5120-SI Series Manuale di installazione

H3C

H3C S5830 Series Manuale utente

H3C

H3C S9500 Series Manuale utente

H3C

H3C S1200 Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente