Haier HP150M5 Scheda tecnica
Heat pump Water Heater
Operation and Installation Manual
Model
HP150M5
Please read this manual carefully prior to
your use of this water heater.
The appearance of the water heater given
in this manual is for reference only.
English
ELECTRICITE
C
E
R
T
I
F
I
É
P
A
R
L
C
I
E
Contents
1. Safety instructions ...............................................................................................................3
2. Instructions on transportation and storage........................................................................6
3. Functionings & principles .....................................................................................................6
4. Technical parameters ...........................................................................................................7
5. Description of parts and components ................................................................................8
6. Installation introduction .....................................................................................................11
7. Operation and functions .....................................................................................................24
8.Checking and maintenance..................................................................................................27
9.Faults and protection ..........................................................................................................28
10.Product Fiche .....................................................................................................................29
Dear users of Haier,
Thank you for choosing Haier products.
Please read this manual carefully and follow the operation and safety instruction to ensure
best installation and utilization of the product.
Product safety statement:
1.This appliance can be used by persons with reduced
physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and
understand the hazards involved.
2. Children shall be closely supervised to make sure they stay
away from this product.
3.The method of installing safety valve please refer to Page 16.
4.The water may drip from the discharge pipe of the pressure
relief device and this pipe must be left open to the
atmosphere.
5.The water heater is to be drained according to the
instructions specified on page 27.
Safety instructions (to be followed at any time)
Failure to respect these instructions may lead to serious malfunctions of the
device and to risks for the user
Instructions with this warning mark shall be strictly followed during operation.
They relate to product and body safety of users.
Information provided with this banning mark relates to activities that are
definitely forbidden. Otherwise the machine may be damaged or users may
risk personal danger.
The water heater shall be
installed in strict accordance
with local wiring regulations,
and equipped with power
supply with a ground line.
Please ensure an effective
ground connection.
It is recommended that the
water heater shall be installed
inside.
The water heater shall not be
installed at places where
water drainage is unavailable
or impossible.
While bathing, children must
be under guidance of an adult
person.
This water storage tank must
be equipped with a safety
valve. Its installation position
shall not be changed. To
guarantee safe operation, it
shall not be blocked at any
time.
Ground line and zero line of the
power supply shall not be
connected together. The
ground line shall not be
connected to pipeline
conveying gas or water,
lightning arresters or
telephone lines.
Interpretation of marks and symbols
English
The outlet water temperature
of a water heater is typically
higher than the temperature
indicated on the display. Hot
water shall not be pointed at
the human body immediately
after opening the hot water
valve to avoid injury caused by
hot water.
Hands or other items shall not
be put into the air grille to
avoid injury or damage to the
water heater.
Means for disconnection from
the main supply having a
contact separation in all poles
that provide full
disconnection under
overvoltage category III
conditions must be
incorporated in the fixed
wiring in accordance with the
wiring rules.
If the power cord is damaged,
it shall be replaced by
qualified professionals to
avoid hazards.
Install the water heater in
strict accordance with the
installation instruction
specified on page 11-23.
Maintenance shall be carried
out according to the
instructions specified on
page 27.
Safety instructions (to be followed at any time)
The water heater is intended to be permanently
connected to the water mains and not connected by a
hose-set.
Do not install the water heater in the position where
exposed to gas, vapours or dust.
The inlet water pressure is between 0.1-0.5MPa. The
inlet water temperature is suggested between 10-30°C.
Rotate the safety valve handle
once a month. The valve
works well if there is water
flowing out, otherwise check
for blocking and replace the
safety valve if necessary.
The appliance contains fluorinated greenhouse gases.
Chemical name of the gas: R134a/ 0,45Kg
Fluorinated greenhouse gases are contained in
hermetically sealed equipment.
Global Warming Potential(GWP) : 1430
Water heaters shall be
equipped with a dedicated
power line and residual
current circuit breakers. The
action current shall not
exceed 30 mA;
Safety instructions (to be followed at any time)
The water drain pipe shall be in connection with the
atmosphere, it shall not be blocked; the water drain pipe
connected to a safety valve shall be installed in a frostless
environment with an continuous downwards inclination.
5
English
In accordance with safety rules, a safety valve(8bar,G1/2F)
must be installed on the tank. For France, we recommend
hydraulic safety units fitted with a membrane with the NF
marking. The rated pressure of the safety valve shall not
exceed 0.8MPa.
If needed, please refer to the wiring diagram on page 23.
The method of connection about the appliance to the
electrical supply refer to page 21.
5
Instructions on transportation and storage
Functionings & principles
1. During transportation or storage, the heat pump water heater shall be packed in the
undamaged package to avoid damage to appearance and performance of the product;
2. During transportation or storage, the heat pump water heater shall be in the upright
position;
3. Under special conditions, this product may be laid down for a short time/distance as
per indication on the side of the package case. The heat pump water heater, after being
laid down for a certain time, shall be kept at upright position for more than 4 hours before
starting up.
The machine shall be kept in the upright position at any time for the best
performance !
A low-pressure liquid refrigerant is vaporized in the heat pump's evaporator and passed
into the compressor. As the pressure of the refrigerant increases, so does its
temperature. The heated refrigerant runs through a condenser coil within the storage
tank, transferring heat to the water stored there. As the refrigerant delivers its heat to the
water, it cools and condenses, and then passes through an expansion valve where the
pressure is reduced and the cycle starts over.
6
7
Technical parameters
Model HP150M5
Tank volume
150L
Rated voltage/ frequency 220V~240V/50Hz
Tank rated pressure 0.8MPa
Corrosion protection Magnesium rod
Water proof grade IPX4
Type of extraction Ambient / Exterior
COP@7 ℃/ EN16147 2.99
COP@14 ℃/ EN16147 3.58
Tapping cycle L
Power input by electric backup 1200W
Rated power input by heat pump 240 W
Maximum power input by heat pump 350W
Maximum power input 1550W
Standby power input/ Pes 20W
Max volume of usable hot water at 40℃
setting at 55℃195.9L
Heating up time (7℃)10h29
Heating up time (14℃) 8h28
Default temperature setting 55
℃
Temperature setting range- with heater 35℃-75℃
Maximum length of air duct
160mm
Max working pressure of refrigerant 0.8/2.8MPa
Refrigerant type / weight R134a/0.46kg
Sound power level 50dB
(A)
Ambient temperature for use of product -7~45℃
Operating temperature of heat pump -7~45℃
Water inlet and outlet connection G1/2"M
Safety valve connection G1/2"M
Drain & Water intlet connection G1/2"M
Product Dimensions 492*537*1680mm
Packing dimension without pallet 587*587*1764mm
Tank
Performances
Dimension and connections
English
Diameter of air duct connection
5m
Net/Gross weight 67/89kg
Packing dimension without pallet 587*587*1894mm
The COP values obtained with external air temperature of 7°C and 14°C, inlet water temperature
of 10°C and set temperature of 54°C (according to EN 16147).
* The COP and noise level data was tested in Haier lab.
Description of parts and components
Accessories
Part
name
Heat pump
water heater Safety
valve
Drainage pipe for
condensate water
Support
plate
Quantity 1111
Inlet for cold
water/drain
outlet
Hot
water
outlet
Heat pump structure
8
Condensate outlet
Air outlet
Air inlet
Instruction
manual
1
HW
SET
ACT
START
STOP
1
2
HP HC
TIMER
MODE SET
BOOST
Description of parts and components
Exploded view
9
2
1
4
3
6
5
17
12 15
14
8
7
13
11
10
18
9
16
English
Air grille
Air channel - front
10
Fan
11
12
Top cover
13
14
15
16
Evaporator
Motor
Air channel - back
17 Back cover
18 Support plate
S/N Description
1
Electric heater
2
Electric cover
3
Cover for display
4
Display panel
5
Front cover
6
Control box
7Compressor
8
9
Four-way valve
S/N Description
Electronic expansion
valve
Installation introduction
Installation precaution
Keep an adequate distance between the working heat pump and the resting room.
- Do not install the water heater in the position where exposed to gas, vapours or dust.
- Install the appliance on a flat, solid surface.The surface can support the machine weight
and the condensate water can be drained freely.
- Noise due to operating and air flow do not bother neighbors.
- Make sure there is sufficient space left for installation and maintenance.
- There is no strong electromagnetic interference around that may affect control
functions.
- There is no sulfur gas or mineral oil existing at the installation place, which may cause
corrosion of the machine and the fittings.
- The water pipe for the water heater used at temperatures below 0°C shall not freeze.
- It shall not be set in rooms where a heating system is used so that heating supply to the
room will not be affected.
- It shall not be set inside a totally-enclosed space.
- The air taken in must in no event be dusty.
- Install the appliance in a dry, frost-free room.
- Temperature of the ambient air or of the air taken in by the heat pump for optimum
running: from 2 to 35°C.
10
Altri manuali per HP150M5
1
Indice
Altri manuali Haier Scaldabagno
Haier
Haier GV270REMB Manuale utente
Haier
Haier Little Sea-ox FCD-JTSA50-III Manuale utente
Haier
Haier FCD-JTHC100A-III Manuale utente
Haier
Haier HP200M3 Scheda tecnica
Haier
Haier ES50H-T1 (E) Manuale utente
Haier
Haier ES10V-M1 Manuale utente
Haier
Haier ES10V-M1 Manuale utente
Haier
Haier ES50V-F1(EU) Manuale utente
Haier
Haier DSF80B E Manuale utente
Haier
Haier ES45V-A1 Manuale
Haier
Haier ES6VQ1 (R) Manuale utente
Haier
Haier ES10V-Q1 Manuale utente
Haier
Haier HP200S1 Scheda tecnica
Haier
Haier HP200S1 Scheda tecnica
Haier
Haier FCD-JTLD100 Manuale utente
Haier
Haier FCD-8 Manuale utente
Haier
Haier FCD-JTHA50-III Manuale utente
Haier
Haier ES50V-F1(R) Manuale utente
Haier
Haier ES8V-Q1(EU) Manuale utente
Haier
Haier Little Sea-ox FCD-JTHC80-III (E) Manuale utente
