Hakko Electronics FM-2030 Manuale utente
MINI PARALLEL REMOVER
Iron holder with a sleep mode
Instruction Manual
l
Thank you for purchasing the FM-2023 mini parallel remover.
Please read this manual before operating the FM-2023.
Please keep this manual readily accessible for reference.
l
CAUTION
• The FM-2023 cannot function by itself. It must be connected to the
HAKKO FM-203 or FM-206 station.
• Specicinformationcanbefoundintheinstructionmanualforyour
HAKKO FM-203/FM-206 station.
TABLE OF CONTENTS
1. PACKING LIST .........................................................1
2. SPECIFICATIONS....................................................1
3. WARNINGS, CAUTIONS AND NOTES ...................2
4. PART NAMES...........................................................3
5. SETTING UP THE FM-2023 ....................................3
6. OPERATION.............................................................4
7. MAINTENANCE .......................................................7
8. TROUBLESHOOTING GUIDE.................................8
9. PARTS LIST ...........................................................10
10. WIRING DIAGRAM ................................................11
1
1. PACKING LIST
Mini parallel remover handpiece ............ 1
Tips (T9-I) 2pcs/set ................................ 1
Heat resistant pad .................................. 1
Heat resistant pad
Iron holder
Mini parallel remover handpiece Tip (shape-I)
Component bed
Connecting cable
Cleaning
sponge
lApplicable Models
In order to function, the FM-2023 must be connected to the HAKKO FM-203 or FM-206
station.
2. SPECIFICATIONS
MODEL FM-2023 Mini Parallel Remover
Power consumption
Temperature range
Tip to ground resistance
Tip to ground potential
Cord assembly
Length (w/o cord)
Weight (w/o cord)
Standard tip
140W (24 V)
200 – 400°C
< 2Ω
< 2mV
1.2m
75mm (w/o tip)
32g (Handpiece only), 5g (I tip only)
T9-I (Shape-I)
∗ This product is protected against electrostatic discharge.
∗Specifications and design are subject to change without notice.
Connecting cable ................................... 1
Iron holder (with Cleaning sponge)......... 1
Component bed...................................... 1
CAUTION:
This product includes such features as electrically conductive plastic parts and grounding of the
handpiece and station as measures to protect the device to be soldered from the effects of static
electricity. Be sure to observe the following instructions:
1. The handle and other plastic parts are not insulators, they are conductors. When replacing parts
or repairing, take sufficient care not to expose live electrical parts or damage insulation materials.
2. Be sure to ground the unit during use.
2
3. WARNINGS, CAUTIONS AND NOTES
Warnings, cautions and notes are placed at critical points in this manual to direct the
operator’s attention to signicant items. They are dened as follows:
WARNING: Failure to comply with a WARNING may result in injury or death.
CAUTION: Failure to comply with a CAUTION may result in injury to the operator, or
damage to the items involved. (One example is given below.)
NOTE: A NOTE indicates a procedure or point that is important to the process being de-
scribed.
CAUTION
When the power is on, the tip temperature is between 200°C/400°F and 400°C/750°F.
Sincemishandlingmayleadtoburnsorre,besuretocomplywiththefollowingpre-
cautions:
lDo not touch the metallic parts near the tip.
l Donotusetheproductnearammableitems.
lAdvise other people in the work area that the unit can reach a very high tempera-
ture and should be considered potentially dangerous.
l Turnoffthepowerwhiletakingbreaksandwhennishedusingtheunit.
lBefore replacing parts or storing the unit, turn off the power and allow the unit to
cool to room temperature.
CAUTION
To prevent damage to the unit and ensure a safe working environment, be sure to
comply with the following precautions:
l Donotusetheunitforapplicationsotherthanthosespecicallydescribedinthe
instruction manual.
lDo not set the tip temperature higher than 400°C/750°F.
lDo not rap the FM-2023 against the work bench to shake off residual solder, or oth-
erwise subject the iron to severe shocks.
lDo not modify the unit.
lUse only genuine HAKKO replacement parts.
lDo not wet the unit or use the unit when your hands are wet.
lThe operating process will produce smoke. Make sure the area is well ventilated.
lPull on the plug to disconnect the FM-2023 from the station outlet. Do not pull the
cord.
3
4. PART NAMES
Heat resistant pad
PlugFixing flange
Iron holder
Component bed
Cleaning sponge
Tip
Plug
Cord
Handle
Button
Connecting cable
5. SETTING UP THE FM-2023
1. Connector cord
Pass the connector cord through the hole
in the heat resistant pad.
2. Iron holder
When the iron holder is connected with the
HAKKO FM-203 or FM-206 station by using
a connecting cable, the sleep function can
be used.
Refer to the HAKKO FM-203 instruction
manual for how to set the sleep time.
Detailed information for HAKKO FM-206 on
how to set the sleep time can be found in
manuals available at the HAKKO Document
Portal. Please download and refer to it.
3. Connections
1. Connect the cord assembly of the FM-
2023 to the receptacle of HAKKO FM-
203 or FM-206.
NOTE:
When MODEL FM-2023 is connected to FM-206,
be sure not to connect an incompatible device
because each receptacle connector differs.
2. Place the FM-2023 in the iron holder.
3. Plug the power cord into the power
supply. Be sure to ground the unit.
Push the plug in as far as
it will go, and try to remove it
without pressing the release pin.
If it stays in the receptacle
it is properly seated.
Receptacle
When the plug ‘clicks’,
it is fully inserted.
NOTE:
This product is protected against electrostatic
discharge and must be grounded for full ef-
ciency.
中継コード
Connecting cable
4
6. OPERATION
l Controls and displays
Refer to the HAKKO FM-203 or FM-206
instruction manual.
NOTE:
The HAKKO FM-203 has 2 channels; D and
S channel. The MODEL FM-2023 can be
connected to only the D channel.
The HAKKO FM-206 has 3 channels: 1, 2
and 3 channel. The MODEL FM-2023 can be
connected to only the channel 2.
Refer to the HAKKO FM-203/FM-206 instruction
manual for details of operating.
There is a flange.
Make sure that the flange will
fit the handle when inserted
into the handpiece.
HAKKO FM-203
soldering station
NOTE:
The tips are a set of 2 pieces with the same
tip style. They must be used together.
l Displays
1. Insert the tips:
Hold the head part of the tip with the
heat resistant pad and insert the tip
into the handpiece. Push until the tip
stops. Repeat for second tip.
2. Turn the power switch ON.
3. When the set temperature is reached,
the buzzer sounds .
Channel D
display lamp
Channel S
display lamp
Channel D
connector
Channel S
connector
5
NOTE:
Once the two tips are inserted into the hand-
piece, heat control begins.
Both tips of the set must be inserted or the
handpiece will not heat.
CAUTION:
Never set the temperature to any value over
400°C (750°F). Doing so may damage the
station. Set the temperature according to the
type of work to be done.
lOperating instructions
1. Set the Temperature
2. Switch lever on the handle
The FM-2023 is double acting.
• When the tips are touching - i.e. the
handpieceisclosed-an‘R’isvisibleon
the handle. Operate by squeezing the
movable part of the handle at the back.
• Whenthehandpieceisopen,an‘N’
is visible on the handle. Operate by
squeezing the movable part of the
handle at the front.
3.Applysolderorux
IfthereisinsufcientsolderonthePWB,
or the soldered area is too small, apply
solder or flux to the PWB. Solder may
also be applied to the tips.
4. Melt the solder
Place the tips on the soldered part and
meltthesolder.Conrmthatthesolderis
fullymelted.Seesketch‘A’.
5. Remove the component
After confirming that the solder is fully
melted, lightly squeeze the handpiece to
grasp the component and lift to remove
thecomponent.Seesketch‘B’.
Place the desoldered chip onto the tray
keeping the tips in parallel, and open
them to release.
CAUTION:
Very high tip temperatures may damage the
printed circuit board, possibly causing the
printed pattern to become detached. HAKKO
recommends setting the tip temperature be-
low 300°C (572°F) for all normal work. Using
the lowest possible effective temperature not
only helps protect parts that are sensitive to
heat, it also helps protect the tip from deterio-
ration caused by heat.
Component
Solder
AB
6
lControl card and
changing the tempera-
ture setting
Please refer to the HAKKO FM-203 or
FM-206 Instruction manual.
lReplacing the tip
Removing and inserting the tip:
Removing the tip:
Hold the handle and pull the tip out of the
handpiece with the heat resistant pad.
Inserting the tip:
Before inserting the tip; Insert the Tip ID
number key into the process gate until the
buzzer sounds once.
Hold head part and insert the tip into the
handpiece. Push until the tip stops.
Hold this part to insert into the handpiece.
24V-140W
FM-2023
Hold the handpiece at the front to remove tip.
24V-140W
FM-2023
CAUTION:
The tip can be very HOT. Use the heat resis-
tant pad for handling hot tips, but do not hold
the hot portion of the tip, even with the pad,
for longer than necessary.
7
7. MAINTENANCE
lTip maintenance
Please refer to the HAKKO FM-203 or FM-206 Instruction manual.
lChecking Procedure
WARNING:
Unless otherwise directed, carry out these procedures with the power switch OFF and the power
UNPLUGGED.
lVerify the electrical integrity of
the heater and sensor
1. Check for a broken heater or sensor
Measure the resistance while at room tem-
perature(15 to 25°C; 59 to 77°F). It should be
8Ω±10%. If the resistance exceeds these limits,
replace the tip.
Measure the resistance across the tip as shown.
lCheck the grounding line 1. Unplug the connection cord from the station.
2. Measure the resistance value between pin 2
and the tip (both tips).
3. Iftheresistancevalueishigherthan2Ω(at
room temperature), remove the black oxide
or replace the tip with a new one. If the resis-
tance value still does not decrease, check the
connection cord for breakage.
lChecking the connection cord
for breakage
1.Insertasetofveriedtipsinbothsidesofthe
handle.
2. Measure the resistance value between two
pins.
Pin 1 - Pin 3 7~9Ω
Pin 5 - Pin 3 8~10KΩ
Pin 7 - Pin 4 7~9Ω
Pin 8 - Pin 4 8~10KΩ
If the measured value exceeds above values, re-
place the FM-2023.
1
4
7
2
8
5
6
3
8
8. TROUBLESHOOTING GUIDE
WARNING:
Disconnect the power plug before servicing.
Failure to do so may result in electric shock.
lThe tip does not heat up.
• The sensor error is dis-
played.
CHECK :Is the tip inserted properly?
ACTION
:Insert the tip completely.
CHECK :Is the connection cord and/or the
heater/sensor broken?
ACTION
:See the appropriate section of this
manual regarding how to check
the connection cord and/or the
heater/sensor for breakage.
lSolder does not wet the
tip.
CHECK : Is the tip temperature too high?
ACTION
: Set the appropriate temperature.
CHECK : Is the tip contaminated with oxide?
ACTION
: Remove the oxide by cleaning the
tip on a damp sponge or HAKKO
599B tip cleaner.
lThe tip temperature is too
high.
CHECK : Is the connection cord broken?
ACTION
:See “Checking the connection
cord for breakage”.
lThe tip temperature is too
low.
CHECK : Is the tip contaminated with oxide?
ACTION
: Remove the oxide by cleaning the
tip on a damp sponge or HAKKO
599B tip cleaner.
lThe soldering iron error
is displayed.
• The LED heater lamp does not
light.
CHECK : Is the connection cord broken?
ACTION
:See “Checking the connection
cord for breakage”.
CHECK : Is the MODEL FM-2023 plug dis-
connected?
ACTION
: Connect the MODEL FM-2023.
9
lThe low-temperature
alarm tolerance error
occurs frequently.
lHeater terminal short
circuit error is dis-
played.
lThe tips cannot be closed.
• The tips will not return to the
original position.
CHECK : Is the tip too small for the items to
be removed?
ACTION
: Use a tip with a large thermal
capacity.
CHECK : Is the setting value for the low
temperature alarm tolerance too
low?
ACTION
: Increase the setting value.
CHECK : Is the tip for MODEL FM-2023?
ACTION
: Turn the power switch OFF and in-
sert the correct MODEL FM-2023
tip. Turn the power switch ON.
CHECK : Is there a foreign object between
the tips?
ACTION
: Remove it.
lTip error or is
displayed.
ACTION
: Contact your Hakko representa-
tive.
Altri manuali per FM-2030
1
Indice
Altri manuali Hakko Electronics Utensili elettrici
Hakko Electronics
Hakko Electronics FU-601 Manuale utente
Hakko Electronics
Hakko Electronics FR-4103 Manuale utente
Hakko Electronics
Hakko Electronics FR400-53 Manuale utente
Hakko Electronics
Hakko Electronics 815 Manuale utente
Hakko Electronics
Hakko Electronics FR-410 Manuale utente
Hakko Electronics
Hakko Electronics FX-9703 Manuale utente
Hakko Electronics
Hakko Electronics FR-4104 Manuale utente
Hakko Electronics
Hakko Electronics FM-2029 Manuale utente
Hakko Electronics
Hakko Electronics FM-2030 Manuale utente
Hakko Electronics
Hakko Electronics FX-600 Manuale utente
Hakko Electronics
Hakko Electronics FR-4102 Manuale utente
Hakko Electronics
Hakko Electronics B5166 Manuale utente
Hakko Electronics
Hakko Electronics FX-601 Manuale utente
Hakko Electronics
Hakko Electronics FX-8003 Manuale utente
Hakko Electronics
Hakko Electronics FM-2023 Manuale utente
Hakko Electronics
Hakko Electronics 951 Manuale utente
Hakko Electronics
Hakko Electronics FR410-52 Manuale utente
Hakko Electronics
Hakko Electronics 807 Manuale utente
Hakko Electronics
Hakko Electronics FR-410 Manuale utente
Hakko Electronics
Hakko Electronics FX-888D Manuale utente
