HAMPTON BAY Tipton II 52" Manuale utente

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varyingclimatic conditions inthe United States this warranty does not

cover any changesin brass finish, including rusting, pitting, corroding, tarnishing orpeeling.

Brass finishes of this type give their longest useful life when protectedfrom varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shallrender the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time period as specified inthe express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow theexclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

581-909

219032

792145351122

Safety Rules.....................................................................................................................................

Unpacking Your Fan ........................................................................................................................

Installing Your Fan ...........................................................................................................................

Installing the Light Kit....................................................................................................................

Your .............................................................................................................

Care of Your Fan ...........................................................................................................................

Troubleshooting ............................................................................................................................

Specifications ...............................................................................................................................

Operating Transmitter

10.

11.

12.

13.

14.

Table of Contents

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been

turned off at the circuitbreaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical

Code and local electrical codes. Electrical installation should be

performed by aqualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do

not use thisfan with anysolid-state fan speed control device.

4. WARNING: To reduce the riskof fire, electric shock, or personal

injury, mount to outlet box marked "Acceptable for Fan

Support of 22.7 kg (50 lbs.) Or Less" and use mounting screws

provided with the outlet box. Most outlet boxes commonly used

for the support of light fixtures are not acceptable for fan support

and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is strongly

recommended.

7. Avoid placing objectsin the path of the blades.

8. Reverse thefan while themotor is on any speeds.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaning the fan.

10. Do notuse water or detergents when cleaning the fanor fan blades.

A dry dust cloth or lightly dampened cloth will be suitable for

most cleaning.

11. After making electrical connections, spliced conductorsshould be

turned upward and pushed carefully up into the outlet box. The

wires should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL Listed and marked suitable for

use with the model fan you are installing. Switches must be UL

General Use Switches. Refer to the Instructions packaged with

the light kitsand switches forproper assembly.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCKOR PERSONAL

INJURY, MOUNT FAN TOOUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted

and capable ofreliably supporting a minimum of 50pounds. Use

only ULListed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance

from the trailingedge of theblades to the floor.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE ARMS(ALSO REFERRED TO ASBRACKETS) DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

Unpack your fanand check the contents. You should havethe following items;

1. Fan blades (5)

2. Canopy assembly

4. Coupling cover

5. Fan motor assembly

6. Blade arms(5)

7. Mounting plate

Ball/downrod assembly (1)

& extra downrod(1)

8. Switch housing

9. Light kit

10. Glass shades

11.

12.

13.

15. Balancing kit

(4)

60 Watt medium base bulbs (4)

Receiver with 6wire nuts

Transmitter+holder+2 mounting screws

+ 2 plastic plugs

14. Extra plasticplug

16. Loose partsbag containing:

a. Blade attachmenthardware

()

b. Mounting hardware

( 3 plasticwire connectors)

16 screws

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED OR MISSING.

CALL TOLLFREE 877-902-5588

Unpacking Your Fan 2.

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

Heavy duty ceiling fan rated outlet box is

required (at least 50 lbs). Donot use regular

outlet box (metalor plastic).

Figure 1,2 and 3 are examples of different

ways to mountthe outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on asteep, sloped ceiling.

Heavy duty fan brace

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Figure 3

Figure 2

Heavy duty

outlet box for fan

Heavy duty

outlet box for fan

Figure 1

Angled ceiling

maximum

18 angle

Hanging the Fan

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise. (Fig.4)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the

bottom of the hanging bracket a half turn from

the screw head and turning the canopy counter

clockwise. (Figure 4)

Step 3. Remove the hanger pin, lock pin and set

screws from the top of the motor assembly. (Fig.

Step 4. Route wires exiting from the top of the

fan motor through the collar cover, canopy cover,

canopy and then through the ball / downrod. (Fig.

Step 5. Align the holes at the bottom of the

downrod with the holes in the collar on top of the

motor housing (Fig.5). Carefully insert the

hanger pin through the holes in the collar and

downrod. Be careful not to jam the pin against

the wiring inside the downrod. Insert the locking

Step 6. Tighten two set screws on top of the fan

motor firmly. (Figure 5)

Step 7. Install the hanger bracket to the outlet

box; be sure to align the holes in the hanger

bracket with the post holes in the outlet box and

secure with screws and washers provided by the

outlet box.(Figure 6)

Step 8. Hanging the assembled fan onto the

mounting bracket, place the downrod ball into

the mounting bracket. Rotate fan until the slot

of the downrod ball locks into the hook of the

mounting bracket. (Figure 7)

Step 9. Secure the safety cable to the building

structure as shown in Fig. 7

Step 10. Connecting the wires (see making the

electrical connections)

WARNING

FAILURETO PROPERLY INSTALL LOCKING

PIN ASNOTED IN STEP5 COULD RESULT IN

FAN LOOSENINGAND POSSIBLY FALLING.

Figure 4

Ceiling

mounting

plate

Ceiling

canopy

Canopy

cover

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 5

Hanger pin

Locking pin Collar cover

Canopy

cover

pin through the hole near the end of the hanger

pin until it snaps into its locked position, as

noted in the circle inset of Fig. 5.

CAUTION

Remove the 5 screws from the motor support plate,

discard the 5 screws and motor support plate.

Screws provided

by the outletbox

Hook

UL Listed

electrial

box

Figure 6

AC Wires

Washers

Hanger

bracket

Posts in the

outlet box

Figure 7

Hanger

bracket Safety cable

CHANGING THE DOWNROD

(OPTIONAL)

NOTE: Your fan comes with a 4" downrod

attached to the hanger ball. In addition you

have been providedwith a 6" downrod to useif

desired. If you choose to use the 6" downrod,

perform the followingsteps:

1. Remove the hanger ball from the 4"

downrod by loosening the set screw at the

top of the downrod which holds the hanger

ball to thedownrod.

2. Slide the hanger ball down the downrod and

remove the supportpin.

3. Insert the support pin in the holes at the top

of the 6" downrod and slide the hanger ball

up the 6" downrod. Make sure the support

pin is properly seated in the grooves in the

top of thehanger ball.

4. Tightenthe set screwfirmly.

Make the Electric Connections

WARNING: To avoid possible electrical

shock, be sure electricity is turned off at the

main fuse boxbefore wiring.

NOTE: This remote control unit is

equipped with 16 code combinations to

prevent possible interference from or to

other remote units. The frequency switches

on your receiver and transmitter have been

preset at thefactory. Please recheck tomake

sure the switches on the transmitter and the

receiver are set to the same position, any

combination of settings will operate the fan

as long as the transmitter and receiver are

set to thesame position.(Figure 8)

Step 1. (Figure 9) Insert the receiver into

the mounting bracket with the flat side of

the receiver facingthe ceiling.

Step 2. (Figure 10) Motor to Receiver

Electrical Connections: Connect the black

wire from thefan to black wire marked "TO

MOTOR L". Connect the white wire from

the fan to the white wire marked "TO

MOTOR N" from the receiver. Connect the

blue wire from the fan to the blue wire

marked "For Light" from the receiver.

Secure the wire connections with the plastic

wire nuts provided.

Step 3. (Figure 10) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white(neutral) wire from the

ceiling to the white wire marked "AC in N"

from the Receiver. Secure the wire

connections with the plastic wire nuts

provided.

Step 4. (Figure 10) If your outlet box has a

ground wire (green or bare copper) connect it

to the fanground wires; otherwiseconnect the

hanging bracket ground wire to the mounting

bracket. Secure the wire connection with a

plastic nut provided. After connecting the

wires spread them apart so that the green

and white wires are on one side of the outlet

box and blackand blue wires are on the other

side. Carefully tuck the wire connections up

into the outletbox.

Note: Fan must be installed at a maximum

distance of 20 feet from the transmitting unit

for proper signal transmission between the

transmitting unit andthe fan's receivingunit.

Figure 9

Receiver

Hanger

bracket

Figure 8

ONON

Code switch

Figure 11

Outlet box

Hanger

bracket

Canopy

cover

Screws

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 10

WHITE

BLUE

BLACK

ONON

Finishing the Installation

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and

over the 2 screws on the hanger bracket.

Rotate canopy clockwise. Next, while

holding the canopy with one hand, slide the

canopy cover over the screws and rotate

clockwise until tight.Note: adjust the canopy

screws as necessary until the canopy and

canopy cover aresnug. (Fig. 11)

WARNING

Make sure thenotch on thehanging

bracket properly sitsin the groovein the

hanger ball beforeattaching the canopyto

the bracket byturning the housinguntil it

drops into place.

Rubber

washer

Blade

arm

Figure 12

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach the blades to the blade arms

using three screws and rubber washers as

shown in Figure 12. Start a screw into the arm,

do not tighten. Repeat for the 2 remaining

screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

Step 3 Fasten the blade arms to the motor by

inserting the tab from the blade arms to the slot

in the bottom motor housing, then tighten the

two screws and washers already installed in the

blade arms (Figure13).

Step 4 Install an optional light kit if you wish.

Follow the instructionsincluded with thekit.

Figure 13

Motor

Blade arm

Slot

Tab

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct

most fan wobbling problems. Check after

each step.

1. Check that all blade and blade arm

screws are secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 14. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance deviation should be equal within

1/8".

3. Use the enclosed Blade Balancing Kit if

the blade wobbleis still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result insmoother operation.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HAMPTON BAY Fan

HAMPTON BAY

HAMPTON BAY Torrington Manuale utente

HAMPTON BAY

HAMPTON BAY Malone Manuale utente

HAMPTON BAY

HAMPTON BAY PALM BEACH III 48-PBH Manuale utente

HAMPTON BAY

HAMPTON BAY 58919 Manuale utente

HAMPTON BAY

HAMPTON BAY ROCKPORT 52250 Manuale utente

HAMPTON BAY

HAMPTON BAY 26829 Manuale utente

HAMPTON BAY

HAMPTON BAY CLARKSTON CF544H-PEH Manuale utente

HAMPTON BAY

HAMPTON BAY MARLSTON N375-MWH Manuale utente

HAMPTON BAY

HAMPTON BAY METARIE II YG922B-MBK Manuale utente

HAMPTON BAY

HAMPTON BAY Glendale Manuale utente

HAMPTON BAY

HAMPTON BAY WITHROP 656 413 Manuale utente

HAMPTON BAY

HAMPTON BAY BPT18-34A-1 Manuale utente

HAMPTON BAY

HAMPTON BAY LEROY 37810 Manuale utente

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-TB Manuale utente

HAMPTON BAY

HAMPTON BAY 597-730 Manuale utente

HAMPTON BAY

HAMPTON BAY MYRON 36LGM-L Manuale utente

HAMPTON BAY

HAMPTON BAY Miramar Manuale utente

HAMPTON BAY

HAMPTON BAY YG188M-NI Manuale utente

HAMPTON BAY

HAMPTON BAY AG510-BN Manuale utente

HAMPTON BAY

HAMPTON BAY Farmington Manuale utente

HAMPTON BAY

HAMPTON BAY NORTH GROVE 52-HASLD Manuale utente

HAMPTON BAY

HAMPTON BAY AC457-WH Manuale utente

HAMPTON BAY

HAMPTON BAY Hawthorne II Manuale utente

HAMPTON BAY

HAMPTON BAY Carriage House-2 138 108 Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio