Hand Held Products 2020 Manuale utente

™

User’s Guide

2020/3820

Cordless System

Disclaimer

Hand Held Products, Inc. (“Hand Held Products“) reserves the right to make

changes in specifications and other information contained in this document

without prior notice, and the reader should in all cases consult Hand Held

Products to determine whether any such changes have been made. The

information in this publication does not represent a commitment on the part of

Hand Held Products.

Hand Held Products shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information which is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated into another language without the prior written consent

of Hand Held Products.

Web Address: www.handheld.com

Microsoft® Pocket PC 2002, Windows®, Windows NT®, Windows 2000,

Windows ME, Windows XP, ActiveSync®, Outlook®, and the Windows logo are

trademarks or registered trademarks of Microsoft Corporation.

The

Bluetooth

®word mark and logos are owned by Bluetooth SIG, Inc.

The 2020/3820 system meets or exceeds the requirements of all applicable

standards organizations for safe operation. However, as with any electrical

equipment, the best way to ensure safe operation is to operate them according

to the agency guidelines that follow. Please read these guidelines carefully

before using your 2020/3820 system.

FCC Class B Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio or television technician for help.

If necessary, the user should consult the dealer or an experienced radio/

television technician for additional suggestions. The user may find the following

booklet helpful: “Something About Interference.” This is available at FCC local

regional offices. Hand Held Products, Inc. is not responsible for any radio or

television interference caused by unauthorized modifications of this equipment

or the substitution or attachment of connecting cables and equipment other than

those specified by Hand Held Products, Inc. The correction is the responsibility

of the user. Use only shielded data cables with this system.

Caution: Any changes or modifications made to this equipment not expressly

approved by Hand Held Products, Inc. may void the FCC authorization to

operate this equipment.

This device and its antenna must not be co-located or operating in

conjunction with any other antenna or transmitter. To maintain

compliance with FCC RF exposure guidelines, use only the

accessories specified by the manufacturer.

Agency Compliance Statements

Canadian Compliance

This Class B digital apparatus complies with Canadian ICES-003. Operation is

subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

3. To prevent radio interference to the licensed service, this device is intended

to be operated indoors and away from windows to provide maximum

shielding. Equipment (or its transmit antenna) that is installed outdoors is

subject to licensing.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe B est conforme à la norme ICES-003 du

Canada. Son fonctionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le

brouillage pouvant causer un fonctionnement indésirable.

3. Pour éviter toute interférence radio avec le service concédé, cet appareil

doit être utilisé en intérieur et à l'écart des fenêtres pour pouvoir fournir une

protection maximale.L’équipement (ou son antenne de transmission)

installé à l’extérieur est soumis à licence.

This device meets or exceeds the requirements of all applicable standards organiza-

tions for safe operation. However, as with any electrical equipment, the best way to

ensure safe operation is to operate them according to the agency guidelines that follow.

Please read these guidelines carefully before using your device.

Regulatory and Safety Approvals

USA: FCC Part 15, Class B

Canada: ICES-003

Regulatory Approvals for Bluetooth Radio Devices

RF devices are designed to comply with the most current applicable standards on safe

levels of RF energy developed by the Institute of Electrical and Electronics Engineers

(IEEE) and the American National Standards Institute (ANSI) and have been recom-

mended for adoption by the Federal Communications Commission (FCC).

RF Approvals

USA: FCC Part 15.247

Canada: RSS 210

CE Compliance

The CE mark on the product indicates that the system has been tested

to and conforms with the provisions noted within the 89/336/EEC

Electromagnetic Compatibility Directive and the 73/23/EEC Low

Voltage Directive.

For CE-related inquiries, please contact:

Hand Held Products

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Hand Held Products shall not be liable for use of our product with equipment

(i.e., power supplies, personal computers, etc.) that is not CE marked and does

not comply with the Low Voltage Directive.

European Regulatory and Safety Approvals

EN 55022 (CISPR 22) Class B

EN60950

EN60825-1

EN55024:1998

This product is marked with in accordance with the Class II product

requirements specified in the R&TTE Directive, 1999/5/EC. The equipment is

intended for use throughout the European Community.

Bluetooth Qualified Product

Bluetooth Qualified Body approved as a Bluetooth Class II radio.

Bluetooth Radio Device R&TTE Compliance

This device is in conformity with all essential requirements of the R&TTE

Directive (1999/5/EC). This equipment has been assessed to the following

standards:

EN 300 328-2:2000

EN 301 489-1 (2002-08)

EN 301 489-17 (2002-08)

EN 60950:2000

This product is marked with in accordance with the product

requirements specified in the R&TTE Directive, 1999/5/EC.

The equipment is intended for use throughout the European Community.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN

INCORRECT TYPE. The battery should be disposed of by a qualified

recycler or hazardous materials handler. Do not incinerate the battery or

dispose of the battery with general waste materials.

NOTE: Any modifications to this device not expressly approved by Hand Held

Products may void your authority to operate it.

Patents

Please refer to product packaging for patent information.

LED Safety Statement

This device has been tested in accordance with IEC60825-1 LED safety, and

has been certified to be under the limits of a Class 1 LED device.

GS Mark

If your product is marked with the GS symbol, then the product has

been issued a GS certificate.

UL and cUL Statement

UL and cUL listed: UL60950-1 and CSA C22.2 No.60950-1-03.

C-Tick Statement

Conforms to AS/NZS 3548. C-Tick number: N10410.

Mexico

Solids and Water Protection

The 3820 has a rating of IP41, immunity of foreign particles and dripping water.

Required Safety Label Locations

Scanner

Compliance

Label

locations

Item Number,

Serial Number

and Revision

Information

location

Base

Compliance

Label

locations

Item Number,

Serial Number

and Revision

Information

location

Chapter 1 - Getting Started

About This Manual ............................................................... 1-1

Unpacking the System .......................................................... 1-2

Models .................................................................................. 1-2

Cordless System: Main Components.................................... 1-3

About the Battery.................................................................. 1-3

Proper Disposal of the Battery ....................................... 1-4

Base Charge Mode................................................................ 1-5

Linking Image Scanner to Base............................................ 1-6

Image Scanner Modes........................................................... 1-6

Unlinking the Image Scanner......................................... 1-6

Single Image Scanner Operation .......................................... 1-7

Locked Link Mode - Single Image Scanner .................. 1-7

Open Link Mode - Single Image Scanner...................... 1-7

Override Locked Image Scanner.................................... 1-7

Multiple Image Scanner Operation....................................... 1-8

Image Scanner Name............................................................ 1-8

Changing Image Scanner Name - Serially ..................... 1-8

Changing Image Scanner Name - via Barcodes............. 1-9

Image Scanner Report......................................................... 1-10

Application Work Groups................................................... 1-10

Application Work Group Selection.............................. 1-11

Resetting the Standard Product Default Settings:

Current Application Work Group .................................... 1-12

Resetting the Standard Product Default Settings:

All Application Work Groups.......................................... 1-12

Using the Image Scanner with Bluetooth Devices ............. 1-13

Changing Bluetooth PIN Code..................................... 1-13

Out-of-Range Alarm........................................................... 1-14

Duration........................................................................ 1-14

Alarm Sound Type ....................................................... 1-14

Data Accumulation Mode................................................... 1-15

Beeper and LED Sequences and Their Meaning................ 1-15

3820 LED Sequences and Their Meaning ................... 1-15

2020 LED Sequences and Their Meaning ................... 1-15

Table of Contents

Basic Operation of the Cordless System ............................ 1-16

System Conditions ....................................................... 1-17

Communication Between the Cordless System and the Host

1-18

Connecting the Base When Powered by Host

(Keyboard Wedge)........................................................... 1-18

Reading Techniques............................................................ 1-20

Resetting the Standard Product Defaults ............................ 1-20

Plug and Play ...................................................................... 1-21

Keyboard Wedge Connection............................................. 1-21

Laptop Direct Connect ................................................. 1-21

RS-232.......................................................................... 1-21

Wand Emulation Plug & Play...................................... 1-22

IBM 4683 Ports 5B, 9B, and 17 Interface .......................... 1-22

Connecting the Base with USB .......................................... 1-23

IBM SurePos ............................................................... 1-25

USB PC or Macintosh Keyboard ................................. 1-25

USB HID...................................................................... 1-26

USB Com Port Emulation............................................ 1-26

Connecting the Base with Serial Wedge ............................ 1-27

Chapter 2 - Terminal Interfaces

Terminal ID .......................................................................... 2-1

Supported Terminals............................................................. 2-2

Keyboard Country ................................................................ 2-4

Keyboard Style ..................................................................... 2-6

Keyboard Modifiers.............................................................. 2-7

Connecting the Base with RS-232 Serial Port...................... 2-8

RS-232 Baud Rate.......................................................... 2-9

RS-232 Word Length: Data Bits, Stop Bits, and Parity2-10

RS-232 Handshaking ................................................... 2-10

Host ACK Selection..................................................... 2-11

Host ACK Enable......................................................... 2-12

Altri manuali per 2020

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hand Held Products Lettore di codici a barre

Hand Held Products

Hand Held Products IMAGETEAM 3800E Manuale utente

Hand Held Products

Hand Held Products 4600g Manuale utente

Hand Held Products

Hand Held Products Quick Check PC600 Manuale utente

Hand Held Products

Hand Held Products 4230 Manuale utente

Hand Held Products

Hand Held Products 4800p Manuale utente

Hand Held Products

Hand Held Products HANDHELD 3800G Manuale utente

Hand Held Products

Hand Held Products 3200 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 4410 Manuale utente

Hand Held Products

Hand Held Products 4X00 Guida rapida

Hand Held Products

Hand Held Products 3800LR Manuale utente

Hand Held Products

Hand Held Products DOLPHIN RF Manuale utente

Hand Held Products

Hand Held Products SCANTEAM 2070 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 3900i Manuale utente

Hand Held Products

Hand Held Products QUICK CHECK 890 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 4620 Manuale utente

Hand Held Products

Hand Held Products 4X00 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 4410 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 3900 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 4410 Manuale utente

Hand Held Products

Hand Held Products IMAGETEAM 3800E Manuale utente

Hand Held Products

Hand Held Products 4800p Manuale utente

Hand Held Products

Hand Held Products 4230 Manuale utente

Hand Held Products

Hand Held Products QUICK CHECK 890 Manuale utente

Hand Held Products

Hand Held Products SCANTEAM 2070 Guida utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente