Harbor Freight Tools OneStopGardens 04819 Guida di riferimento rapido
04819
ASSEMBLY & OPERATING INSTRUCTIONS
®
MINI-COLD FRAME
GREENHOUSE
3
Brought to You by Augusta Flint
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s
record below:
Model___________ Serial No._____________ Purchase Date_____________
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating
and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the
invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry
place for future reference.
Technical Specifications
Construction: 3/4" and 11/32" Tubular Steel, injection molded polypropylene brackets
welded 1/8" Rod Steel
Cut and stitched vinyl cover with front zipper
Overall
Dimensions: 27-3/8" Width x 19-3/8" L x 85-1/2" H (with cover)
Weight: 30 LBS.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use this product in damp or wet locations. Don’t
expose to rain. Keep work area well lighted.
3. Store idle equipment. When not in use, products must be stored in a dry location to inhibit
rust. Always lock up products and keep out of reach of children.
4. Use the right product for the job. There are certain applications for which this product was
designed. It will do the job better and more safely at the rate for which it was intended. Do not
modify this product and do not use this product for a purpose for which it was not intended.
5. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.
6. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the product.
#04819 Page 2
Brought to You by Augusta Flint
Additional Warnings
1. Avoid Sharp edges when assembling.
2. Keep product usage area clean. Greenhouse can be hosed off when cleaning.
3. Always check hardware and assembled parts after assembling. Place in an area that is
flat and level. All connections should be tight and hardware tightened.
4. Use extreme caution when moving the assembled Greenhouse. Do not lift the
Greenhouse without assistance. Wear gloves and be careful to avoid pinching of fingers.
Damage of plants and stored items may occur if dragged. You may wish to disasemble prior to
moving and reassemble in new location.
5. Do not allow children to play in, stand upon or climb upon the Greenhouse. Do not place
anything on top of the Greenhouse Dome. This is a delicate assembly.
6. Avoid harsh weather conditions. The Greenhouse could topple in strong winds. Creatively
anchor with rocks or sandbags along the “Skirt Flap.” Disassemble if weather conditions could
damage the Greenhouse.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must be
supplied by the operator.
Assembly
Your Mini-Cold Frame Greenhouse will require complete assembly prior to use. It is important that
you read the entire manual to become familiar with the product BEFORE you use the Greenhouse.
Before assembling the Mini-Cold Frame Greenhouse be sure that you have all parts described in
the Parts List and Assemby Diagram located on the last pages of this manual.
Step 1) Place two (2) Plastic Joints (#1) parallel on the floor of your work area. Connect the
two Plastic Joints (#1) by inserting a Steel Tube (#3) into the bottom/center holes-
see Step 1 of the Assembly Diagram and Figure 1 below.
Note that Steel Tubes (#3) are thicker than Steel Tubes (#2) and Vertical Tubes (#4).
Figure 1
Steel Tube (#3) Steel Tube (#2)
Vertical Tube (#4)
Plastic Joint (#1)
Steel Tube (#2)
#04819 Page 3
Brought to You by Augusta Flint
#04819 Page 4
Step 2) Insert Steel Tube (#2) into the hole in one Plastic Joint (#1), then into the hole
directly across on the second Plastic Joint (#1). Repeat for the remaining two (2)
Steel Tubes (#2) and other two holes in each Plastic Joint (#1)-see Figure 1 and
Assembly Diagram Step 1.
Step 3) Repeat Step 1 and Step 2 for each of the remaining four (4) shelf assemblies.
Step 4) Insert one Vertical Tube (#4) into hole in each corner of Plastic Joint (#1). Place
completed shelf assembly (see Steps 1, 2 and 3) with Plastic Joints (#1) onto Vertical
Tube (#4).
Step 5) Repeat Step 4 until all four shelf assemblies are in place-see Figure 2 on page 4.
Step 6) Once you have used all 16 Vertical Tubes (#4) and completed shelf assembly,
insert the ends of one Top Tube (#5) into both Plastic Joints at top of Greenhouse-
see Figure 3. Repeat for 2nd Top Tube (#5).
Step 7) Place Wire Shelves (#6) on each of the bottom 3 shelf assemblies. Place Half Wire
Shelf (#7) on fourth level shelf assembly.
Step 8) Place Polypropylene Cover (#8) over entire steel assembly. Wrap the Velcro straps at
the bottom around the Vertical Tubes on each side of Greenhouse to secure in place.
The front opening can be unzipped, rolled up and tied at the top to maintain an
opening in the Greenhouse to provide ventilation and access to shelves.
Unpacking
When unpacking your Mini-Cold Frame Greenhouse, check to make sure the following parts are
included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
Parts List
Part # Description Quantity Part # Description Quantity
1 Plastic Joint 10 5 Top Tube 2
2 Steel Tube 15 6 Wire Shelf 3
3 Steel Tube 5 7 Half Wire Shelf 1
4 Vertical Tube 16 8 Polypropylene Cover 1
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LI-
CENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Brought to You by Augusta Flint
Figure 2
Vertical Tube (#4)
Shelf Assembly
Insert ends of Top Tube (#5)
into Plastic Joints (#1)
Figure 3
Plastic Joint (#1)
Top Tube (#5)
Assembly and Parts Diagram
#04819 Page 5
2
2
3
1
5
4
4
7
6
6
8
Brought to You by Augusta Flint
Indice
Altri manuali Harbor Freight Tools Kit serra
