Harvia Digital KIP Manuale utente

This guide should be used in conjunction with the manufacturer’s heater manual found inside the heater box.

Please be sure you and your electrician review both before installation.

Digital KIP Heater

Installation & Owner’s Guide

Read this entire manual through to the end before proceeding with the installation.

KIPW HEATER INSTALLATION MANUAL |PAGE 2

HEATER INSTRUCTIONS

Your Almost Heaven Sauna is paired with a genuine Finnish heater manufactured by Harvia Oy, the world leader in sauna heaters.

Refer to this guide for installation and operation instructions. Please note, a licensed electrician should perform all electrical

work, and Almost Heaven Saunas sta is available to assist with any questions you or your electrician may have. Please call us at

888-355-3050 for technical assistance.

PERFORMANCE EXPECTATION

Based on its cubic footage, your sauna kit has been paired with an appropriately sized heater to achieve optimal sauna

temperatures. Properly installed, you should expect your KIP heater to consistently heat your sauna to at least 170 F at

approximately head height when sitting on the bench. This temperature should be achieved in 45-60 minutes, although this

timeframe can be longer depending on the ambient temperature outdoors.

Please note, saunas at elevations greater than 5,000’above sea level may not perform as eciently as they would at sea level.

If you are above this threshold and are not achieving the aforementioned expectations, please contact Almost Heaven Saunas

technical support.

HEATER WARRANTY

Your Harvia heater comes with a 1 year warranty on the heating elements, and a 5 year warranty on the other components.

Information for your electrician:

4.5kW and 6.0kW KIP Heaters

 • 30-ampdoublepolebreaker

 • 240volts

 • 1Phase

 • 10/2wire.Ifthedistanceisgreaterthan90feetfromthepowersource,werecommendusingan8/2wireto  

accommodate for voltage drop.

 • DonotuseGFCIwiththisheater

 • Usecopperwirewith90Cinsulation

8.0kW KIP Heaters

 • 40-ampdoublepolebreaker

 • 240volts

 • 1Phase

 • 8/2wire

 • DonotuseGFCIwiththisheater

 • Usecopperwirewith90Cinsulation

KIPW HEATER INSTALLATION MANUAL |PAGE 3

Note: It is possible you will receive two temperature sensors - one in the heater box and one in the Xenio control box. They are the same

sensor - set one aside as a spare for possible later use.

The KIP heater is a wall mounted unit. Position the heater in the designated heater location in your sauna according to the

instructions below.

Removethehardwarebagfromthebaggiewiththesafetyplacards(2),selectingthetwolongerlagscrews(1.5”).Youwillsecure

theseintothesaunawallsothat¼”ofthescrewprotrudesfromthewall

a. For barrel saunas,the11/2”lagscrewsshouldbemountedapproximately20”othelowestpointofthebarrelandspaced15

1/4”apartandcenteredabovetheventholes.Note:TheheaterwillconcealaportionoftheLEDlight.Thisisnormal.

b. For indoor saunas,thescrewsshouldbemounted20”otheoor,andspaced151/4”apartapproximatelycenteredabovethe

ventholes(ifpresent).Itisnethattheheateriscoveringtheholesasventilationstilloccurs.

20”

15 ¼ ”

20”

15 ¼ ”

Touchpad

Temperature sensor

PowerUnit

KIPW HEATER INSTALLATION MANUAL |PAGE 4

Hangtheheateronthemountingscrewstoensureitislevelandthatitsbasesits5-7”otheoorofthesauna.

If these criteria are met, make a mark on the wall of the sauna directly behind one of the rubber gaskets on the lower back of the

heater; this will be where the power enters the sauna. Take the heater o the wall and remove the rubber gasket, exposing the

cutout. It does not matter which gasket is removed.

NOTE: While this location is the most common, the power can enter the sauna at any location. It is not recommended you use the pre-

drilled vent holes as an entrance for the conduit.

Removethetwoscrewsholdingthestoneguardinplace.Prytheguardbackandliftuptoremoveit.Cliptheziptieholdingthe

heating elements in place being sure the tie doesn’t fall into the heater.

Flip the heater on its back and remove the bottom cover so your electrician can gain access to the terminal block.

KIPW HEATER INSTALLATION MANUAL |PAGE 5

POSITIONING THE HEATER COMPONENTS

Indoor Saunas

For indoor sauna applications, mount the power unit on or near the sauna. It can be mounted on the exterior of the sauna, or on

anadjacentwall.Themainpowerforyourheaterwillconnecthererst,andthenrelayontoyourheater.Next,considerwhere

you’d like to mount your touchpad. You can mount the touchpad wherever it’s most convenient for you. We do not recommend

mounting the touchpad in the sauna itself.

Outdoor Saunas

Neitherofthesecomponentsarewaterproof,soproperprecautionsshouldbetakenforoutdoorsaunaapplications.Please

consider the following:

Power Unit

• Thepowerunitshouldbemountedinadrylocation.Ifitcannotbemountedinadry

location, then it should be mounted in a ventilated weatherproof enclosure.

• Pleasenotethatthetemperaturesensorthatcomeswiththesaunakithasa15’reach-the

sensor is mounted in the sauna and connects to the power unit. If the sauna is located

greater than this distance away from where the power unit is installed, then the power

unit should be mounted nearer to the sauna in a weatherproof enclosure with proper

ventilation. The image on the right is an example of an enclosure. Alternatively, you can

purchase a longer temperature sensor wire directly from Almost Heaven Saunas.

Touchpad

• Thetouchpadshouldbemountedindoorsinadryarea.

• Thetouchpadconnectstothepowerunitwiththeprovided20’datacable.Ifyouneedalongerdatacableforyour

application, you may purchase one directly from Almost Heaven Saunas.

KIPW HEATER INSTALLATION MANUAL |PAGE 6

CONNECTING YOUR HEATER TO POWER

Pleasenote,thepowerunitprovided(CX170-U1-15)withyoursaunaisratedforsingle-groupconnection.Theinstructionsbelow

are for single group connections only.

Incoming Power

First, you will need to bring power to your power unit. Remove the power unit’s cover and pry

out the appropriate knockouts that will allow the wiring to enter and exit the unit.

Connectthepowercordtotheappropriateterminals,withthetwohotlinesconnecting

totheleft-mostL1andL2terminals,andthegroundconnectingtothegroundterminal.A

neutral line is not needed - this is only required if a light or ventilation fan is connected to the

powerunit,anapplicationthatisnotavailableintheU.S.market.

Outgoing Power

Next,you’llwanttorelaypowertotheheateritself.

First,connectthegroundatthepowerunittothegroundterminalattheheater.Next,

connectoutgoingL1toT1attheheater,andoutgoingL2toT3attheheater.Next,complete

thehigh-limitsafety-circuitbyconnectingA1atthepowerunittoT2attheheater,andA2

atthepowerunitunittoT4attheheater.Youmayusestrandsof12gawireforthehigh-limit

safety circuit connections.

***NOTE: If your heater arrived with copper jumpers pre-installed in the heater’s terminal block,

please remove and discard these. These are not needed.

Temperature Sensor

The temperature sensor mounts in your sauna and provides feedback to the power unit

regardingthetemperatureinyoursauna.Weadvisemountingthissensorapproximately14”tothesideoftheheater,and

approximately14”belowthehighestpointofthe

sauna.Usetheprovidedhardwaretomountthesensor.

KIPW HEATER INSTALLATION MANUAL |PAGE 7

Next,feedthesensorwireoutofyoursaunainordertoconnecttothepowerunit.

Secure the wiring to the circuit board mini-terminal. Starting on the outside and moving in, the wires should connect in the

following order: blue - white - red - yellow.

Touchpad

The touchpad should be mounted indoors in a dry location, preferably in your

home.Onceyou’vedeterminedthislocation,useaatheadscrewdrivertogently

pry the screen of the touchpad from the mounting bracket. Feed the data cable

through the hole in the mounting bracket, and mount the bracket to the location

you selected. Push the data cable connector into the port on the back of the screen

and snap the screen back into the bracket.

Next,connecttheothercabletotheportclosesttothepowerunit’smini-terminal

block that is connected to the temperature sensor. Replace the power unit’s cover

and turn the power switch to the on position.

PLACING THE STONES

Rinse your sauna stones to prepare them for placement. Beginning between the back wall and back heating element, place the

smaller stones in between and around the three heating elements being sure that the heating elements stay in their original

vertical position and do not touch each other. The stones should touch the elements, but not bend them. Reserve the

larger stones for placement on top of the heating elements, covering them completely. Replace the stone guard you removed at

the beginning of the heater installation.

Note:Packingstonesintootightlywillrestrictairowandaecttheeciencyofyourheater.Looselypositionthestonesaround

and above the heating elements. It is common to have 5-10 stones left over.

Temperature Sensor

Touchpad data cable

KIPW Heater Installation & Owner’s Manual

almostheaven.com

OPERATING YOUR HEATER

Note:Yourtouchpad’sdefaultsettingsarecompatiblewithyourheater.Nochanges

are necessary.

Immediate Start

Turn your breaker on. If everything is connected correctly, the buttons at the bottom of the

screen should illuminate. The bottom left button is the main power unit - press it, and you

shouldhearaloud“clunk”fromthepowerunit,whichisthecontactorsengaging.Ifyoudo

nothing, it will begin heating immediately; the display will show the current temperature in the

sauna, as well as the time remaining on the heat cycle.

Delayed Start

Turnthepowerbuttononthetouchpad.Press“menu”untiltheclockiconisashing.Adjustthe

preset time by pressing + or - until you get to the desired preset time. You are able to preset your

heaterin10minuteincrementsforupto12hours.Thetimeremainingbeforeyourheaterbegins

heating should appear below the brackets at the top of the touchpad.

Setting the Temperature

The temperature displayed on the screen is the temperature inside the sauna where the temperature sensor is mounted. To set

yourdesiredsaunatemperature,pressthepowerbuttononthetouchpad.Press“menu”untilthethermometericonashes.

Adjust the temperature with the + or - until your desired temperature is displayed. The sauna will heat to and hover around this

temperature.

GENERAL OPERATION INFORMATION

• YourDigitalKIPheaterisULcertied.Becauseofthis,itisrequiredtoshutoafteronehourofuse.Ifyouwishtocontinue

your sauna session, you will have to restart the heater if the heating period times out.

• Ifyourheaterisn’theating,turnoyourbreakerandtrypressingtheresetbuttonundertheheaterasthehigh-limitsafety

circuit may have been tripped. If this continues to happen, your sensor may be too high or too close to the heater.

• Thisisatraditionalsaunaheaterwithsaunastones.Assuch,youmaypourwaterontothestonesaccordingtoyour

humidity level preference. Please note, however, it often only takes a ladle-full to achieve the desired eect.

If there is an error code displayed on the touchpad, please refer to the error code list found in the manufacturer’s manual

12-2022

Indice

Altri manuali Harvia Stufa

Harvia

Harvia KV-80 Manuale utente

Harvia

Harvia sentiontec Concept R mini Series Manuale utente

Harvia

Harvia HYB300230S Guida

Harvia

Harvia Vega Manuale del proprietario

Harvia

Harvia sentiotec Home combi Manuale utente

Harvia

Harvia MD135SA Manuale utente

Harvia

Harvia HPCS6U1H Manuale del proprietario

Harvia

Harvia Sentiotec Concept R CP-RCB-090 Manuale utente

Harvia

Harvia FG Series Manuale utente

Harvia

Harvia M45 Manuale utente

Harvia

Harvia PO11 Manuale utente

Harvia

Harvia AV-4 Guida

Harvia

Harvia sentiotec Concept R mini Manuale utente

Harvia

Harvia FORTE Manuale utente

Harvia

Harvia SENTIO Qube 240 Guida

Harvia

Harvia PO12-U1 Manuale del proprietario

Harvia

Harvia HAFU4502401 Manuale del proprietario

Harvia

Harvia HL16U1 Manuale del proprietario

Harvia

Harvia E Virta HLS6U1SA Manuale del proprietario

Harvia

Harvia sentiotec HWO-035NS-P Manuale utente

Harvia

Harvia Delta E HDE360400 Manuale utente

Harvia

Harvia Type KIP45 Manuale utente

Harvia

Harvia M45 Manuale utente

Harvia

Harvia KIP-30-B1 Manuale del proprietario

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente