Hawg Wired RC-Link RC104 Manuale utente

C-

-L

K™

™

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 2 FREMONT, CA

CONGRATULATIONS! YOU’VE JUST PURCHASED WHAT WE CONSIDER TO BE THE FINEST MOTORCYCLE

AUDIO EQUIPMENT AVAILABLE. WE TAKE PRIDE IN THE FACT THAT YOU’VE CHOSEN HAWG WIRED

PRODUCTS, AND WELCOME YOU TO OUR FAMILY OF AUDIOPHILE ENTHUSIASTS. OUR GOAL HERE IS

SIMPLE –TO BRING HIGH PERFORMANCE AUDIO FIDELITY TO YOU, THE RIDER, WITHOUT COMPROMISING

YOUR BIKE’S ELECTRICAL SYSTEM OR STORAGE SPACE. SOME SIDE EFFECTS MAY OCCUR HOWEVER,

INCLUDING BUT NOT LIMITED TO; PUZZLED LOOKS FROM OTHER MOTORISTS, OCCASIONAL SHOUTS

FROM YOUR NEIGHBORS, AND THE ENVY OF YOUR FRIENDS. AFTER YEARS OF DESIGN

AND ENGINEERING, CUSTOM CRAFTSMANSHIP, AND A CRAVE FOR CLEAN, CLEAR,

LOUD MUSIC, WE BELIEVE WE’VE NAILED THIS STUFF DOWN RIGHT.

THANK YOU FOR YOUR SUPPORT

THE HAWG WIRED TEAM

PLEASE RECORD THE MODEL AND SERIAL NUMBER[S] OF YOUR EQUIPMENT IN THE SPACE PROVIDED

BELOW AS YOUR PERMANENT RECORD. THESE NUMBERS CAN BE FOUND ON THE FRONT AND/OR

BOTTOM OF EACH COMPONENT. THIS WILL ASSIST US WITH YOUR FACTORY WARRANTY COVERAGE, AND

MAY BE USEFUL TO YOU IN THE UNFORTUNATE EVENT THAT IT’S STOLEN.

MODEL NUMBER[S]:

SERIAL NUMBER[S]:

KIT ITEMS INCLUDED (BY QUANTITY):

RC104

RC104 REMOTE CONTROL MODULE

RC-LINK REMOTE CABLE (RJ12 TO RJ12 COILED)

RC-LINK COMMUNICATION CABLE (RJ12 TO RJ12 FLAT)

PASS-THROUGH COUPLER (RJ12 TO RJ12)

PASS-THROUGH COUPLER BRACKET

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 3 FREMONT, CA

THIS SECTION IS INTENDED TO BRING YOU UP TO SPEED WITH OUR DOCUMENTATION CONVENTIONS.

WE RECOMMEND READING THIS MANUAL THOROUGHLY BEFORE BEGINNING YOUR INSTALLATION TO

ACHIEVE A TROUBLE FREE, LONG LASTING OUTCOME.

TERMINOLOGY USED IN THIS MANUAL:

RC-LINK

REFERS TO THE PROPIETARY BUS TECHNOLOGY THAT LINKS MULTIPLE AMPLIFIERS

TO A SINGLE REMOTE CONTROL MODULE. THE GOODS YOU JUST PURCHASED.

RC-LINK MODULE

REFERS TO THE REMOTE CONTROL MODULE ITSELF. THE SMALL GREY AND BLACK

BOX WITH BUTTONS AND LEDS THAT COMES WITH THIS KIT.

POWER AMPLIFIER

CS300, RS400, MASTER 2 CHANNEL AMPLIFIER THAT FUNCTIONS STANDALONE OR

LINKED IN SERIES. IF YOU DON’T OWN ONE OF THESE, YOU’RE OUT OF LUCK.

RC-LINK CABLE

RJ12 TO RJ12 CABLES THAT LINK THE REMOTE MODULE AND AMPLIFIERS

TOGETHER. ONLY USE THE CABLES SUPPLIED WITH THIS KIT.

LOW LEVEL LINK CABLE

3.5MM PHONO JACK CABLE THAT LINK TWO OR MORE AMPLIFIERS TO THE SAME

INPUT SOURCE, ONLY USED IN MULTIPLE AMPLIFIER INSTALLATIONS.

BATWING FAIRING

HARLEY-DAVIDSON®TERM FOR THE FAIRINGS ON ELECTRA GLIDE (FLHT) MODELS,

FORK MOUNTED, SINGLE HEADLIGHT STYLE.

SHARKNOSE FAIRING

HARLEY-DAVIDSON®TERM FOR THE FAIRINGS ON ROAD GLIDE (FLTR) MODELS,

FRAME MOUNTED (FIXED), DUAL HEADLIGHT STYLE.

MANUFACTURER INSTRUCTIONS

REFERS TO ANY DOCUMENTATION PROVIDED BY A MANUFACTURER OTHER THAN

HAWG WIRED (IE. HARLEY-DAVIDSON®SHOP REPAIR MANUAL, AFTERMARKET

SOURCE UNIT OR SPEAKER MANUAL, ETC.).

QUICK CONNECT SYMBOLS:

KEEP AN EYE OUT FOR THE “QUICK CONNECT” SYMBOLS THROUGHOUT THIS MANUAL; THEY PROVIDE A

VISUAL LINK BETWEEN INSTRUCTIONS, DIAGRAMS, AND THE REMOTE CONTROL CONNECTIONS.

RC-LINK IN

RC-LINK INPUT PORT, REMOTE CONTROL OR AMPLIFIER LINKING

RC-LINK OUT

RC-LINK OUTPUT PORT, AMPLIFIER LINKING

LINE-IN

SOURCE INPUT, LOW LEVEL OR HIGH LEVEL INPUT

LINE-OUT

LOW LEVEL OUTPUT, FEED FOR ADDITIONAL AMPLIFIER DEVICE LINKING

POWER

BATTERY POSITIVE (+12VDC)

FUSE

ESSENTIAL PROTECTION FROM SHORTS

BAD

BATTERY VOLTAGE DEAD, CHECK YOUR CHARGING SYSTEM

BATTERY VOLTAGE OK BUT NOT GREAT, CHECK YOUR CHARGING SYSTEM

GOOD

BATTERY VOLTAGE GREAT, ALL IS WELL, RESUME AUDIO PLAYBACK

CONFIGURE

AMPLIFIER CONFIGURATION AND TEST (GAIN, CROSSOVERS, ETC.)

TOOLS

TOOLS REQUIRED, DISASSEMBLY OR REASSEMBLY WORK TO PERFORM

CAUTION

CAUTIONS, NOTES, TIPS, OR SPECIFIC INFORMATION TO BE AWARE OF

NOTE: IF ANYTHING ABOUT THE INSTRUCTION OR INFORMATION PROVIDED IN THIS MANUAL IS UNCLEAR, QUESTIONABLE,

OR YOU THINK WE’RE DEAD WRONG ABOUT SOMETHING, PLEASE CONTACT US.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 4 FREMONT, CA

RC-LINK CONTROL CONNECTIONS

FOR FAIRING REMOVAL AND RE-ASSEMBLY INSTRUCTIONS, REFER TO YOUR AMPLIFIER INSTALLATION MANUAL OR

MANUFACTURER INSTRUCTIONS. AND WHILE YOU HAVE IT APART, TAKE A VISUAL INVENTORY OF YOUR INNER FAIRING.

SECURING ANY LOOSE WIRES OR LOOMS WITH ZIP TIES.

1. CHOOSE A LOCATION FOR THE LINK CABLE COUPLER AND MOUNT IT WHERE IT CAN BE

ACCESSED WITH THE FAIRING COVER IN PLACE. CONNECT THE SUPPLIED FLAT LINK CABLE

FROM THE BACK-SIDE OF THE COUPLER TO THE FIRST (OR ONLY) AMPLIFIER IN PORT.

2. MULTIPLE AMPLIFIER CONFIGURATIONS: CONNECT YOUR AMPLIFIERS TOGETHER USING THE

SUPPLIED FLAT LINK CABLES IN THE ORDER IN WHICH YOU WANT THE AMPLIFIERS TO BE

SELECTED BY THE REMOTE. NOTE THE IN AND OUT PORTS OF EACH AMPLIFIER, AND CONNECT

THEM ACCORDING TO THE DIAGRAM BELOW.

NOTE: THE ORDER OF THE AMPLIFIERS IN YOUR CONFIGURATION AND HOW THEY RELATE TO THE

DESIGNATIONS AMP1 –AMP4 AT THE REMOTE CONTROL MODULE IS ENTIRELY UP TO YOU.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 5 FREMONT, CA

REMOTE CONTROL OVERVIEW

AMPLIFIER STATUS OVERVIEW

THE RC-LINK REMOTE CONTROL HAS TWO BASIC MODES OF OPERATION WHEN

CONNECTED TO THE RC-LINK PORT(S) OF YOUR AMPLIFIER(S); MONITOR AND

PROGRAM. PRESSING THE AMPLIFIER SELECT BUTTON CYCLES BETWEEN THESE

TWO MODES.

MONITOR MODE (DEFAULT POWER-UP MODE):

THE APPLICABLE AMPLIFIER LEDS WILL LIGHT UP FOR EACH AMPLIFIER

DETECTED. THE LED CORROSPONDING TO EACH AMPLIFIER DETECTED WILL

FLASH IF AN OVER-CURRENT, OVER-DRIVE (CLIPPING), OR OVER-TEMPURATURE

CONDITION OCCURS. ALL DETECTED AMPLIFIERS WILL FUNCTION NORMALLY IN

MONITOR MODE. GAIN AND FREQ LEDS WILL BE OFF.

PROGRAM MODE:

ONLY THE LED CORROSPONDING TO THE AMPLIFIER BEING PROGRAMMED WILL

LIGHT UP, LEAVING ALL OTHER AMPLIFIER STATUS LEDS OFF. EACH AMPLIFIER

NOT BEING PROGRAMMED IS ALSO ATTENUATED (MUTED), LEAVING ONLY THE

CURRENTLY SELECTED AMPLIFIER FUNCTIONING NORMALLY FOR

PROGRAMMING. THE LED CORROSPONDING TO THE AMPLIFIER BEING

PROGRAMMED WILL STILL FLASH IF AN OVER-CURRENT, OVER-DRIVE (CLIPPING)

OR OVER-TEMPURATURE CONDITION OCCURS DURING PROGRAMMING.

NOTE: ONCE THE REMOTE HAS ENTERED INTO PROGRAMMING MODE, THE ADJUSTMENT

KNOBS ON EACH AMPLIFIER DETECTED WILL BE DISABLED, REGARDLESS OF WHETHER

OR NOT ANY SETTINGS ARE CHANGED, AND WILL REMAIN DISABLED UNTIL EACH

AMPLIFIER IS RESET MANUALLY (SEE RESETTING THE AMPLIFIER(S) IN THE TEST AND

TUNE SECTION OF THIS MANUAL).

WARNING: USE ONLY HAWG WIRED PROVIDED RC-LINK CABLES AND COUPLERS. WHILE THEY RESEMBLE TYPICAL

HOUSHOLD PHONE WIRES, THEY ARE NOT. NO OTHER DEVICE OR CABLE SHOULD EVER BE CONNECTED TO THIS JACK,

AND DOING SO COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.

BATTERY STATUS OVERVIEW

THE RC-LINK REMOTE CONTROL HAS A BUILT-IN BATTERY MONITOR THAT

REPORTS THE STATUS OF YOUR CHARGING SYSTEM.

BATTERY MONITOR (OPTIONAL):

WITH THE CIGARETTE LIGHTER ADAPTER CABLE CONNECTED TO THE REMOTE

CONTROL MODULE, THE BATTERY STATUS LEDS INDICATE THE CURRENT STATE OF

THE CHARGING SYSTEM. THE BATTERY STATUS MONITOR FUNCTIONS

INDEPENDENT OF THE AMPLIFIER MODES, AND IS NOT REQUIRED FOR AMPLIFIER

STATUS OR PROGRAMMING.

WARNING: USE ONLY HAWG WIRED PROVIDED CIGARETTE ADAPTER CABLES WITH THIS DEVICE. NO OTHER DEVICE OR

CABLE SHOULD EVER BE CONNECTED TO THIS JACK AS POLARITY (+/-) AND POWER JACK SIZES MAY VARY. DOING SO

COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 6 FREMONT, CA

TEST AND TUNE

SETTING THE GAIN:

WITH THE REMOTE IN PROGRAMMING MODE AND THE DESIRED AMPLIFIER SELECTED, FOLLOW

THESE STEPS TO SET THE GAIN CONTROL:

1. TURN THE GAIN CONTROL ALL THE WAY DOWN ( - BUTTON).

2. SET ALL TONE (BASS, TREBLE) AND EQUALIZATION CONTROLS (BALANCE, FADE) ON THE

SOURCE UNIT TO “FLAT” OR “0”, AND TURN OFF “LOUD” OR “LOUDNESS”. IF A SEPARATE

EQUALIZER IS USED, DISABLE OR SET ALL OF ITS CONTROLS TO “FLAT” OR “0”.

3. WHILE PLAYING A STANDARD NON-MP3 CD1, SET THE SOURCE UNIT’S VOLUME CONTROL TO

75% OF MAXIMUM LEVEL.

4. SLOWLY INCREASE GAIN ( + BUTTON) UNTIL YOU HEAR A SLIGHT DISTORTION OF THE AUDIO

PLAYBACK. BACK OFF THE GAIN UNTIL THE DISTORTION GOES AWAY.

WARNING: SETTING THE GAIN TOO HIGH IN AN ATTEMPT TO GET “MORE VOLUME” CAN NOT ONLY CAUSE PREMATURE

DISTORTION, BUT CAN ALSO DAMAGE YOUR SPEAKERS. IF YOUR SYSTEM CONFIGURATION RESULTS IN YOUR GAIN

CONTROL BEING SET OUTSIDE THE TYPICAL RANGE AS INDICATED ABOVE, CALL US TO RESOLVE THE PROBLEM.

SETTING THE CROSSOVER:

WITH THE REMOTE IN PROGRAMMING MODE AND THE DESIRED AMPLIFIER SELECTED, FOLLOW

THESE STEPS TO SET THE CROSSOVERS:

1. SET ALL TONE (BASS, TREBLE) AND EQUALIZATION CONTROLS (BALANCE, FADE) ON THE

SOURCE UNIT TO “FLAT” OR “0”, AND TURN OFF “LOUD” OR “LOUDNESS”. IF A SEPARATE

EQUALIZER IS USED, DISABLE OR SET ALL OF ITS CONTROLS TO “FLAT” OR “0”.

2. WHILE PLAYING A STANDARD NON-MP3 CD1, SET THE CROSSOVER FILTER TO THE DESIRED

FREQUENCY, KEEPING IN MIND THAT TOO MUCH BASS AT HIGH VOLUMES CAN CAUSE

PREMATURE DISTORTION AND SPEAKER FAILURE.

NOTE1: THIS IS THE PREFERRED AUDIO TESTING SOURCE METHOD, AS MP3, XM, FM, AND AM ALL HAVE SOME LEVEL OF

COMPRESSION OR DEGRADATION INVOLVED, WHICH CAN LEAD TO VARYING RESULTS. IF THE PREFERRED METHOD IS

NOT AVAILABLE, USE THE MOST COMMON PLAYBACK METHOD YOU USE WHILE RIDING.

RESETTING THE AMPLIFIER(S):

WITH THE REMOTE DISCONNECTED AND THE AMPLIFIER(S) FUNCTIONING NORMALLY, FOLLOW

THESE STEPS TO RESET THE AMPLFIER(S):

1. SET BOTH GAIN AND CROSSOVER KNOBS ON THE AMPLIFIER TO “MIN” OR “0”.

2. SLOWLY BEGIN TURNING UP THE GAIN KNOB TO MANUALLY ADJUST THE AMPLIFIER. THE

AMPLIFIER IS NOW RESET.CONTUNE TUNING THE AMPLIFIER MANUALLY (REFER TO THE

AMPLIFIER INSTALLATION GUIDE FOR MORE INFORMATION ON MANUALLY ADJUSTMENT).

NOTE: IF YOU RECONNECT THE REMOTE MODULE AFTER MANUALLY ADJUSTING THE AMPLIFIER(S), THE REMOTE

SETTINGS WILL ASSUME THE CURRENT MANUAL SETTINGS OF THE AMPLIFIER ADJUSTMENT KNOBS.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 7 FREMONT, CA

[

]

CONNECTORS AND CONTROLS

PLANNING YOUR SYSTEM CONFIGURATION IS THE FIRST STEP TOWARDS HI-FI HAPPINESS, SO IT’S TIME

YOU GET FAMILIAR WITH ALL THE BELLS AND WHISTLES YOUR NEW SYSTEM HAS TO OFFER. THE TABLE

BELOW LISTS THE CONTROLS AND CONNECTORS OF THE REMOTE CONTROL MODULE FOR REFERENCE.

AMPLIFIER SELECTOR

AMPLIFIER INDICATORS

BATTERY STATUS INDICATORS

GAIN PLUS (UP)

CROSSOVER PLUS (UP)

BATTERY MONITOR JACK

GAIN INDICATORS

CROSSOVER INDICATORS

RC-LINK OUTPUT PORT

GAIN MINUS (DOWN)

CROSSOVER MINUS (DOWN)

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 8 FREMONT, CA

[

]

CONNECTORS DEFINED

BATTERY INPUT JACK:

THIS CONNECTOR ALLOWS THE REMOTE CONTROL MODULE TO MONITOR YOUR CHARGING SYSTEM

AND PROVIDE FEEDBACK BASED ON THE VOLTAGE LEVEL. THIS CONNECTION IS OPTIONAL AND NOT

REQUIRED FOR THE CONTROL MODULE TO FUNCTION. TYPICALLY USED FOR DIAGNOSTICS ONLY.

WARNING: USE ONLY HAWG WIRED PROVIDED CABLES AND WIRING. NO OTHER DEVICE OR CABLE SHOULD EVER BE

CONNECTED TO THIS JACK. DOING SO COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.

RC-LINK OUTPUT PORT:

THIS CONNECTOR PROVIDES THE INTERFACE TO THE AMPLIFIER(S) IN YOUR SYSTEM

CONFIGURATION. IT CONNECTS TO THE FIRST (OR ONLY) AMPLIFIER RC-LINK IN PORT. EACH

ADDITIONAL AMPLIFIER (IF APPLICABLE) CONNECTS IN A CHAIN LINK METHOD ACCORDING TO THE

DIAGRAM IN THE INSTALLATION SECTION OF THIS MANUAL.

WARNING: USE ONLY HAWG WIRED PROVIDED CABLES AND WIRING. NO OTHER DEVICE OR CABLE SHOULD EVER BE

CONNECTED TO THIS PORT. DOING SO COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.

CONTROLS DEFINED

INPUT GAIN ADJUSTMENT:

A COMMON MISCONCEPTION ABOUT GAIN ADJUSTMENT IS THAT “MORE GAIN = MORE VOLUME”.

ACTUALLY, IT’S NOT THE VOLUME THAT’S BEING INCREASED, BUT RATHER THE AMPLIFIER’S

SENSITIVITY TO THE SOURCE INPUT. BY INCREASING THE GAIN LEVEL, YOU’RE INCREASING HOW

SENSITIVE THE AMPLIFIER IS TO THE SIGNAL IT RECEIVES FROM THE SOURCE UNIT. THIS IS WHY

IT’S IMPORTANT TO SET THE GAIN PROPERLY, RATHER THAN SIMPLY TURNING THE KNOB UNTIL IT’S

REALLY LOUD.

WARNING: SETTING THE GAIN TOO HIGH IN AN ATTEMPT TO GET “MORE VOLUME” CAN NOT ONLY CAUSE PREMATURE

DISTORTION, BUT CAN ALSO DAMAGE YOUR SPEAKERS. IF YOUR SYSTEM CONFIGURATION RESULTS IN YOUR GAIN

CONTROL BEING SET OUTSIDE THE TYPICAL RANGE AS INDICATED ABOVE, CALL US TO RESOLVE THE PROBLEM.

CROSSOVER FILTER ADJUSTMENT:

THE PURPOSE OF A CROSSOVER CIRCUIT IS TO FILTER OUT A SPECIFIC RANGE OF FREQUENCIES

FROM A SPEAKER’S INPUT TO MAXIMIZE ITS PERFORMANCE. FOR A TWEETER, THE GOAL IS TO

FILTER OUT LOW (BASS) RANGE FREQUENCIES TO MAXIMIZE THE HIGH RANGE (TREBLE) RESPONSE.

CONVERSELY, FOR A SUBWOOFER, THE GOAL IS TO FILTER OUT THE HIGH AND MID RANGE

FREQUENCIES, LEAVING ONLY LOW FREQUENCIES TO PLAY THROUGH THE WOOFER.

DEFAULT: WHEN USING ANY HAWG WIRED MID-RANGE OR TWEETER SPEAKERS, THE RECOMMEND

SETTINGS ARE HIGH PASS MODE WITH THE FREQUENCY FILTER SET AT OR ABOVE 150HZ.

WARNING: SETTING THE CROSSOVER TOO LOW IN AN ATTEMPT TO GET “MORE BASS” CAN NOT ONLY CAUSE PREMATURE

DISTORTION, BUT CAN ALSO DAMAGE YOUR SPEAKERS. IF YOUR SYSTEM CONFIGURATION RESULTS IN YOUR

CROSSOVER CONTROL BEING SET ALL THE WAY UP OR DOWN, CALL US TO RESOLVE THE PROBLEM.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 9 FREMONT, CA

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE

HAWG WIRED PAGE 10 FREMONT, CA

[

]

Indice

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione