Hay PC LINEAR Manuale utente
– INSTRUCTION MANUAL –
DESIGN BY PIERRE CHARPIN
PC LINEAR
GENERAL INFORMATION
TECHNICAL DATA
This product is supplied with an integrated LED
light source. The expected lifespan of the LED
light source is 25,000 hours, which equates to
810 years of general use. When the light source
reaches its end of life, the whole luminaire should
be replaced. For dimming, please check which
wall mounted dimmers are compatible with the
included LED driver.
FITTING TYPE | Integrated LED
POWER W | 28W
COLOUR TEMPERATURE | 2800K warm white
ATTENTION
Ensure that the power supply to the circuit has
clearly been turned OFF before installing the
product. In some countries, electrical installation
must be carried out by authorised electricians/
contractors; please check with your local
authority for guidance.
The product must not be modified in any way.
HAY accepts no responsibility for any products
that have been modified or tampered with. The
external flexible cable or cord of this luminaire
cannot be replaced. If the cord is damaged,
the luminaire should be replaced. This lamp is
designed for indoor use only.
CARE AND MAINTENANCE
The product can be cleaned with a soft damp
cloth and mild detergent, or a dry microfibre
cloth. Do not use alcohol or any other solvents
to clean the product and avoid using abrasive or
rough sponges. Ensure that the power supply has
been turned OFF before cleaning the product.
PARTS
Lamp with suspension
wire & cable
Ceiling capMounting bracket
LED driver Suspension mount
1.
Unpack all the parts and check that you have received all the
parts listed. Mark the position of the holes to be drilled (104 cm apart)
on the ceiling.
104 cm
2.
Drill the holes using the correct type of drill for the ceiling you are drilling into.
3.
Insert the wall plugs. Ensure you use the correct type of wall plugs for
the type of ceiling.
4.
Fix the suspension mount to the ceiling using the provided screws.
Disassemble the suspension mount as shown below and insert each screw into
the suspension mount, screwing them firmly into place.
5.
Once the suspension mounts are firmly in place, the lamp is ready to be mounted.
Start by pulling the suspension wire through the disassembled suspension mount
(step 1). Guide the wire though the fixed suspension mount and through the exit hole
on the side (step 2). Screw the disassembled suspension mount together with the
part that is fixed to the ceiling (step 3). The suspension wire is now safely in place
(step 4). Repeat on the other side.
Step 1
Step 3
Step 2
Step 4
6.
Level the lamp by adjusting the wire. Pull the wire to shorten it or press the tab
of the suspension mount to release it. It is recommended that two persons
perform this step.
7.
Once the lamp is in place, the excess wire trailing from the exit hole can be cut.
Note that once the wire has been cut, the lamp can no longer be lowered.
Indice
Altri manuali Hay Illuminazione domestica
Hay
Hay SLANT Manuale utente
Hay
Hay SLANT Manuale utente
Hay
Hay MOUSQUETON Manuale utente
Hay
Hay Arcs Wall Manuale utente
Hay
Hay FIFTY-FIFTY WALL Manuale utente
Hay
Hay MATIN WALL Manuale utente
Hay
Hay APEX Manuale utente
Hay
Hay PC Table Series Manuale utente
Hay
Hay PAO GLASS TABLE LAMP Manuale utente
Hay
Hay CLOCHE Manuale utente
Hay
Hay NOC CLAMP Manuale utente
Hay
Hay ARCS SHADE Manuale utente
Hay
Hay ROPE TRICK Manuale utente
Hay
Hay Matin Floor Manuale utente
Hay
Hay LBM TABLE LAMP Manuale utente
Hay
Hay PC PORTABLE Manuale utente
Hay
Hay APOLLO PORTABLE Manuale utente
Hay
Hay APOLLO PORTABLE Manuale utente
Hay
Hay TURN ON Manuale utente
Hay
Hay PC TABLE LAMP Manuale utente
