HEB MWD-600 Manuale utente

Packing list

Instrument Name: Closed Intelligent Microwave Digestion System

Instrument Model: MWD-600

No. Name Picture Quantity

Main Body 1

Touch-screen Controller 1

High Pressure Digestion Combined Tank 12

Pressure Control Device 12

Explosion-proof Framework 12

6Sample Loading Platform

Auxiliary Platform 1

Exhaust Pipe 1

Tank Holder 1

Unload Tool 1

Pressure-plate 2

Controller Protective Box

Controller Serial Cord 1

Power Cord 1

Operation Manual 1

Inspector: Inspection Date:

Тля тендера UA-2017-07-19-000683-а

Closed Intelligent Microwave Digestion System

MWD-600

Operation Manual

Тля тендера UA-2017-07-19-000683-а

Important Statement

Please read the operation manual seriously and completely before using the

instrument, make sure to fully understand all safety related matters, to ensure the

instrument running safely, high efficiency and smoothly.

During operation, please strictly follow the requirements in the operation

manual, Please pay special attention to the contents begin with the mark ‘NOTE’,

‘CAUTION’, ‘WARNING’ and the bold important warning content, to ensure the

instrument running smoothly and safety and to avoid unnecessary loss and

damage. If the users don’t comply with the operation manual or don’t follow the

lab routine operation attentions and accident happens, our company will not take

any responsibility.

Please put the operation manual in a convenient place for future reference.

The content of the manual has the possibility to change and modify without prior

notice.

Тля тендера UA-2017-07-19-000683-а

Content

Chapter 1 General Introductionof Microwave Digestion System．．．．．．．．．．．．．1

Chapter 2 Instrument Structures and Accessories．．．．．．．．．．．．．．．．．．．．．．．．．2

2.1 MWD-600 Introduction of External Structures．．．．．．．．．．．．．．．．．．．2

2.2 MWD-600 Major Accessories．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．2

Chapter 3 InstallationConditions andInstallationGuide．．．．．．．．．．．．．．．．．．．．4

3.1 MWD-600 Installation Conditions．．．．．．．．．．．．．．．．．．．．．．．．．．．．4

3.2 MWD-600 Installation Guide and Maintenance．．．．．．．．．．．．．．．．．．5

Chapter 4 Technical Specifications．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．7

Chapter 5 Safety Guide．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．8

5.1 Operation Safety Guide．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．8

5.2 Accessories Safety Guide．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．8

5.3 Pressure Module Safety Guide．．．．．．．．．．．．．．．．．．．．．．．．9

5.4 Temperature Module Safety Guide．．．．．．．．．．．．．．．．．．．．．9

5.5 Sample &Acid Solution Safety Guide．．．．．．．．．．．．．．．．．．．．．．．．．9

5.6 Other Considerations．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．10

Chapter 6 Instrument Operation Guide．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．11

6.1 Instrument Operation Flowchart．．．．．．．．．．．．．．．．．．．．．．．．．．．．．11

6.2 Assembly of High Pressure Digestion Combined Tank．．．．．．．．．．．12

6.3 Considerationsof usingDigestion Tank．．．．．．．．．．．．．．．．．．．．．．．．13

6.4 Introductionof OperationInterfaces．．．．．．．．．．．．．．．．．．．．．．．．．14

Chapter 7 Instrument Quality Guarantee．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．19

Chapter 8 Instrument Maintenance．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．21

Equipment Warranty．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．22

Тля тендера UA-2017-07-19-000683-а

Chapter 1 GeneralIntroduction of Microwave Digestion System

Thank you for purchasing and using MWD-600 Closed Intelligent Microwave Digestion

System. We are very grateful for your trust, we will try our best to ensure that in coming days

your instrument running smoothly. In addition, if you need to form a complete set of

pretreatment equipment, welcome to choose and buy SPH-1 Sample Pretreatment Heating

Equipment which is tailored specifically for MWD series products.

Microwave digestion technology is a highly efficient sample preparation technology that

develops fast in recent years. It means,in a sealing container, using microwave heating principle,

under high temperature and high pressure to achieve the quickly and completely digestion of

inorganic or organic samples. Microwave digestion technology could well satisfy the

requirements of modern analytical instrument for sample preparation, with the advantages of

fast and uniform heating, less reagent dosage, low blank value, not easily polluted, energy

efficient, etc. Especially in the analysis of volatile element, it’s better to maintain sample

integrity and has a higher sample rate.

Microwave digestion system general consists of main body, temperature control system,

pressure control system, digestion tank, rotor system, exhaust system and software system.

MWD-600 Closed Intelligent Microwave Digestion System is a high-end microwave digestion

instrument. It has zero consumables design, all digestion tanks’ temperature and pressure

double control and display, self-recover sealing of high-pressure digestion function, sample

solution of the actual temperature and pressure monitoring and zero lag function. The MWD-600

is especially suitable for AAS, UV-VIS, ICP-AES, AFS, GFAA, XFS, ICP-MS, HPLC, etc. analysis; it

could accelerate the reaction, shorten processing time and improve the work efficiency. At

present the microwave digestion technology has been widely used in food, textile, geology,

metallurgy, plastics, coal oil, cosmetics, chemical, biological medicine, environment, wastewater

treatment, battery manufacturing, and other fields.

Тля тендера UA-2017-07-19-000683-а

Chapter 2 Instrument Structures and Accessories

2.1 MWD-600 Introduction of External Structures

1 Upper Cover 2 Door Handle 3 Touch-screen Line

4 Touch-screen Controller

5 Pause Button 6 Turn Button 7 Door Switch Button 8 Instrument Model

9 Air Outlet 10 Air Intake 1 11 Touch-screen Serial Port

12 Upper Computer Serial Port 13 Air Intake 2

2.2 MWD-600 Instrument Accessories

2.2.1 Major Accessories

(1) Main Body

It’s one of the main components of the instrument, in which the digestion experiment

would be finished completely.

(2) Touch-screen Controller

It’s the liaison between operator and instrument, using “man-machine conversation”

control model.

(3) Pressure Control System

It monitors and controls the pressure changes in real time during the digestion process.

Тля тендера UA-2017-07-19-000683-а

(4) Temperature Control System

It monitors and controls the temperature changes in real time during the digestion

process.

(5) Digestion Tank

The digestion tank consists of a High Pressure Digestion Combined Tank and an Explosion-

proof Framework.

(6) High Pressure Digestion Combined Tank

The high pressure digestion combined tank combined by a sample digestion tank and a

protective outer tank. The sample digestion tank also known as the inner tank used to

contain the samples and acids .It provides a closed environment for the high temperature

and high pressure digesting, volume 100 ml. The protective outer tank also known as the

outer tank, it provides a protective environment for the high temperature and high

pressure digesting.

(7) Explosion-proof Framework

It provides a further security for the high temperature and high pressure digesting.

(8) Rotor System

It combined by a drive motor, a sample loading platform and an auxiliary platform. The

sample loading platform provides a space for loading the digestion tank. The auxiliary

platform provides a stable platform for monitoring the pressure. The drive motor keeps the

sample loading platform rotating uniformly and continuously on the auxiliary platform

toward the same direction.

(9) Exhaust System

It can blow out the spilling acids from the digestion tank in time and cool the digestion tank

when digestion completed.

(10)Software System

It ensures the instrument running intelligent and efficient.

2.2.2 Other Accessories

(1) Tank Holder

Users can place the inner tank into the tank holder.

(2) Unload Tool

Users cantake out the inner tank thattoo tight to remove after digestion with it.

(3) Pressure-plate

Users can calibrate instrument pressure signal in Instrument Calibration Interface with the

pressure-plate. There are two pressure-plates, the thick one is pressure-plate-6 that is used

to calibrate P6, and the thin one is pressure-plate-3 that is used to calibrate P3.

Тля тендера UA-2017-07-19-000683-а

Chapter 3 Installation Conditions and Installation Guide

3.1 MWD-600 Installation Conditions

Please confirm the following conditions before installing the

instrument. 3.1.1 Working Power Supply

(1) Working Voltage: AC 220V, ±10%.

(2) Working Frequency: 50 or 60Hz, ±4%.

(3) Working Power: More than 2200W. The power should be over 2500W if there is any other

assist device.

(4) Earth Wire: Earth resistance should not be less than 100Ω, and should be in accordance

with the relevant regulations. The plug must be plugged into an outlet that is properly

installed and earthed.

3.1.2 Worktable

(1) The instrument must be installed on a horizontal and stabilization worktable over 640mm

length and over 630mm width which could bear over 75kg weight.

(2) The bigger worktable is required if assist device is also installed on the same worktable.

(3) For correct operation, the instrument must have sufficient air flow. Allow with 200mm of

space at the back and both sides of the instrument.

(4) The instrument is around 1055mm height when opening the upper cover, Please select

suitable worktable for the convenience of instrument operation.

(5) It is allowed to place the worktable next to the fume hood, but it is strictly prohibited to

put the instrument into the fume hood. Please avoid strong or continue vibration.

3.1.3 Installation Environment

The stand or fall of instrument working environment has a great influence for the

instrument performance and service life. Please confirm the following environment of the

installation place.

(1) Working environment temperature range: 5～40℃。

(2) Working environment humidity range: 45～85％。

(3) Storage environment temperature: -20～70℃。

(4) Indoor environment:

1) Make sure that there is no acidic or alkaline gas in room.

2) Make sure that there is no corrosive organic gas to etch the paint in room, especially for

gases such as benzene.

3) Make sure that there is concentrated exhaust device in room. Do not use the

instrument in corrosive gas environment and long time, that’s not conducive to the

instrument maintenance.

4) The external surface of instrument should be kept clean frequently.

(5) Sample Reagent

1) Please don’t place the corrosive solution such as sample reagents, acid and alkali

solution near the instrument.

2) It must be careful when taking the corrosive solution to avoid dripping or upset on the

surface of instrument or furnace chamber or the accessories such as digestion tank or

platform. If happened, please wipe clean immediately with a soft cloth or paper.

Тля тендера UA-2017-07-19-000683-а

(6) Other Important Notes

1) Make sure there is enough space for user’s operation.

2) Make sure to keep the instrument avoiding the direct sunlight. Long time sunlight would

lead to the pain of the instrument surface discoloration or loss.

3) Make sure to avoid the strong and continual shock or shake, which will affect

instrument performance.

4) Make sure there is no any heating device near the instrument, to prevent the

instrument shell temperature over 70℃.

5) It is forbidden to use the instrument together with any other high power electrical

appliance at the same time.

6) The instrument should be far from the water supply, to avoid the water into the

instrument and cause the danger of electricity leakage.

7) The instrument should be far from the high intensity magnetic field, electric field and

high frequency wave equipment, to avoid disturbing the uniform distribution of the

magnetic field and decrease the heating efficiency.

8) Keep working voltage stable to avoid any noise which will affect instrument accuracy.

9) Avoid frequent switching the electrical equipment which is using the same power supply

withthe instrument.

3.2 MWD-600 Installation Guide and Maintenance

3.2.1 The microwave digestion system should be installed by technical persons.

Before installation, please make preparation.

3.2.2 Instrument Installation

(1) Packing Opening: Please do not place it in horizontal or inverted direction. Avoid shocking

when opening the packaging, take out of the instrument and place it on the worktable.

(2) Checking: Check all the spare parts and accessories, if there is any damage, please

contact distributor or our company.

(3) Installation Procedure

WARNING: The 220V voltage may cause electrical shock hazards, please connect

the power cord after finishing installation procedure.

1) Take out of the exhaust pipe from the accessory box. Install the side with hoop set into

the air outlet on the back of the instrument and fix it. Connect the other side to the

exhaust system.

2) Take out of the auxiliary platform from the accessory box and fix it into the two locating

pins in the furnace chamber with the beads upward.

Тля тендера UA-2017-07-19-000683-а

3) Take out of the sample loading platform from the accessory box and fix it into drive

shaft in the furnace chamber. Pay attention to the thick card slot in line with the drive

shaft thickness direction.

4) Put the assembled digestion tank into the tank positioning slot (assembly process of

digestion tank, please to see Chapter sixth 6.2). If multiple digestion, please make the

digestion tanks evenly arranged in the loading platform.

5) Take out of the touch-screen controller from the accessory box and connect it to the

touch-screen serial port on the back of the instrument.

6) The connection of the power cord and the ground wire

WARNING: The 220V voltage may cause electrical shock hazards, please make sure

the power switch is in the state of closed (0) before connecting the power cord.

uMake sure power supply and ground wire is normal.

uMake sure the voltage of power supply is normal.

uInsert two sides of the power cord respectively into the power grid socket and

the power supply socket of the instrument.

7) Make sure the connection of the power line and the ground wire is normal. Put the

power switch to “1”, the instrument is powered on and enters the Automatic System

Check Interface. When system checks to “Pressure detecting…” it stops and prompts

“no digestion tank” if you don’t load the digestion tank before power on, you can load

the assembled digestion tank and close the door and press the button of [Check] to

continue the pressure checking. If you don’t need to check the pressure you can press

the button of [Skip] to jump to the Function Selection Interface.

Тля тендера UA-2017-07-19-000683-а

Indice

Altri manuali HEB Attrezzature da laboratorio

HEB

HEB Z160 Manuale utente

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente