HiB 33100 Manuale utente

FI #05 003 R160908 Ver No. 1.0 Jan 2016

Hush & Breeze Wall Mounted Fans

Thank you for purchasing this HiB product.

Please read through these instructions carefully and refer back to them during

installation to ensure that your product is ﬁtted safely and that it retains its high

quality ﬁnish.

Please retain this leaﬂet for future reference.

Before drilling, ensure there are no hidden cables or pipes in the wall

Please see Fig. 1 on the back page for details

Suitable for installation in zones: 2 & Outside Zones

Breeze Chrome

Timer Art no.32800

Timer & Humidity Sensor Art no.32900

Breeze Matt Silver

Timer Art no.31300

Timer & Humidity Sensor Art no.31400

Breeze White

Timer Art no.31100

Timer & Humidity Sensor Art no.31200

Hush Chrome

Timer Art no.33100

Timer & Humidity Sensor Art no.33200

Hush Matt Silver

Timer Art no.31700

Timer & Humidity Sensor Art no.31800

Hush White

Timer Art no.31500

Timer & Humidity Sensor Art no.31600

Electrical Connection

Please ensure that the fan unit is positioned in

accordance with the diagram below i.e. With

the electrical access point (5) top le.

Fitting

1) Choose a suitable position for your fan

according to Figure 1 on the back page. Use

a cable ﬁnder to check if there are any buried

cables or pipes in the wall or ceiling. Draw

around the outside of the fan with a pencil to

determine it’s exact position.

2) Make a suitable sized hole in the wall/

ceiling with the appriopiate tools.

N.B. If wall mounted ensure the hole is

angled slightly downward to stop any

moisture running back into the motor.

If mounted in the ceiling ensure the hole is

between the joists.

3) Fit ﬂexible ducting into the hole, ﬂush

with both sides of the wall. Ensure the

duct slopes slightly downwards towards

the outside. Make good any plasterwork

around the duct.

4) Position the fan back into place, and mark

the four ﬁxing points. Drill the required

holes in the marked positions. If drilling

through tile, use a ceramic drill bit. Insert

wall plugs into the drilled holes.

5) Follow a similar procedure for the outside

wall grille.

6) If ceiling mounted the ducting should be

routed to the nearest soﬃt.

1 Holes for fan mounting (x4)

2 Terminal block

3 Electrical access points

4 Wire ﬁxing rack

Breeze

Hush

1 Casing

2 Fan propeller

3 Function module

4 Protective cover of terminal block

5 Electrical access point

Fascia removal

Hush - Depress plastic nodule on the side of the

fascia and gently prise away from the casing.

Breeze - In order to remove the fascia for

maintenance, please remove the small retaining

screw and gently prise the fascia away from the

casing.

Technical Information -

Hush

Power input: 220-240 V, 50 Hz

Maximum ventilation volume: 97 m3/hr (±5%)

Power consumption: 7.5W

Dimensions: W158 x H158 x D107mm

Breeze

Power input: 220-240 V, 50 Hz

Maximum ventilation volume: 88 m3/hr (±5%)

Power consumption: 14W

Dimensions: W152 x H152 x D126mm

hib.co.uk 3

1) Ensure the domestic electrical mains supply

to which the fan is being connected is turned

oﬀ. This product is designed to be connected

to an on/oﬀ switch outside the bathroom, or

to a ceiling mounted pull cord switch.

2) Hush Only: Remove the front panel and

protective cover (4). Pass the power wire

through the hole in the rubber plug (beneath

protective cover) at the fan casing ﬂange.

3) Breeze Only: Remove the protective grille.

Cut out blanking plug of electrical access

point (3) and lead the power supply cords

through the hole.

4) Make the electric connections according

to the relevant wiring diagram below. See

diagram of ceiling rose to ensure correct

feeds are used. Please note that the

fan may operate immediately when

connected, this is normal and due to a

residual charge le during testing.

Operating Instructions

1) For Art Nos. 33100/31700/31500/

32800/31300/31100

Fan with timer option switches on as control

voltage is supplied to LT terminal. Aer

voltage is oﬀ, the fan continues operating

within the set time period T, adjustable

between 2 and 30 min. The time is regulated

by turning the potentiometer T clockwise to

increase and anticlockwise to decrease the

run time.

2) For Art Nos. 33200/31800/31600/3290

0/31400/31200

Fan with timer and humidity sensor will

operate when a control voltage is applied

to the LT terminal OR when the humidity

exceeds that set on the potentiometer.

If this is set at its lowest (60%) the fan

will run most of the time. When set at the

highest setting (90%) the fan will only

operate at higher level humidity. Once

humidity has been reduced the fan will

run until the required setting on the timer

is reached. Time T and humidity H values

are regulated by turning the appropriate

potentiometers T and H clockwise to

incr ease and anticlockwise to decrease

the running-out time and humidity level

respectively. To set the maximum humidity

level set the potentiometer in H max (90%)

position.

1) Maintenance

Fan maintenance is to be performed only aer

the fan is disconnected from the mains power

supply. Maintenance means periodic clearing

of the surfaces from dust and dirt.

5) Fix the fan to the wall using 4 screws.

6) Replace the cover and protective grille.

Hush

Breeze

Ceiling Rose

N.B. Always use the plastic screwdriver provided

to adjust the settings to avoid damaging the

control unit.

Ceiling mounted...

For ceiling mounting follow procedure for wall

mounting making sure ducting isn’t mounted

vertically to the outside. This is to ensure

moisture doesn’t come back into the motor.

Do not

mount vertically

LT (Switch Live)

220 - 240 V

LT (Switch Live)

220 - 240 V

MAINS IN

SWITCH

EARTH

NEUTRAL LOOP LINE

LAMP/FAN

These products are suitable for installation in zones: 2 &Outside Zones

All installations must comply with guidelines which are based on a zonal concept. The diagram above

illustrates this concept and must be followed to ensure the safe installation of electrical appliances in

the bathroom. These regulations apply to domestic installations only. Installations must be made in

accordance with the current IEE wiring regulations and relevant building regulations. HiB recommends

that all electrical bathroom products should only be ﬁtted by a suitably qualiﬁed, Part P registered

electrician.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and

make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter speciﬁcations as necessary. E & OE.