HIK VISION DS-K1801 Series Manuale utente

DS-K1801 Series Card Reader

User Manual

UD05259B-A

User Manual

Any and all information, including, among others, wordings, pictures, graphs

are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its

subsidiaries (hereinafter referred to be “Hikvision”). This user manual

(hereinafter referred to be “the Manual”) cannot be reproduced, changed,

translated, or distributed, partially or wholly, by any means, without the

prior written permission of Hikvision. Unless otherwise stipulated, Hikvision

does not make any warranties, guarantees or representations, express or

implied, regarding to the Manual.

About this Manual

This Manual is applicable to 1801 series card reader

The Manual includes instructions for using and managing the product.

Pictures, charts, images and all other information hereinafter are for

description and explanation only. The information contained in the Manual

is subject to change, without notice, due to firmware updates or other

reasons. Please find the latest version in the company website

(http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the properties of Hikvision in

various jurisdictions. Other trademarks and logos mentioned below are the

properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT

DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS

PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES

NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR

PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL

HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE

TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT

DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS

PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION,

IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT

TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE

OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,

VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT

LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO

ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION

SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH

ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

0200001070323

iii

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to

comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and

comply therefore with the applicable

harmonized European standards listed under

the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be disposed

of as unsorted municipal waste in the

European Union. For proper recycling, return

this product to your local supplier upon the

purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed

of as unsorted municipal waste in the

European Union. See the product

documentation for specific battery

information. The battery is marked with this

symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper

recycling, return the battery to your supplier or to a designated

collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards

requirements.

Safety Instruction

These instructions are intended to ensure that user can use the

product correctly to avoid danger or property loss.

The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious

injury or death.

Cautions: Neglecting any of the cautions may cause injury or

equipment damage.

Warnings Follow these

safeguards to prevent

serious injury or death.

Cautions Follow these

precautions to prevent potential

injury or material damage.

Warnings

All the electronic operation should be strictly compliance with the

electrical safety regulations, fire prevention regulations and

other related regulations in your local region.

Please use the power adapter, which is provided by normal

company. The power consumption cannot be less than the

required value.

Do not connect several devices to one power adapter as adapter

overload may cause over-heat or fire hazard.

Please make sure that the power has been disconnected before

you wire, install or dismantle the device.

When the product is installed on wall or ceiling, the device shall be

firmly fixed.

If smoke, odors or noise rise from the device, turn off the power

at once and unplug the power cable, and then please contact the

service center.

If the product does not work properly, please contact your dealer

or the nearest service center. Never attempt to disassemble the

device yourself. (We shall not assume any responsibility for

problems caused by unauthorized repair or maintenance.)

Cautions

Do not drop the device or subject it to physical shock, and do not

expose it to high electromagnetism radiation. Avoid the

equipment installation on vibrations surface or places subject to

shock (ignorance can cause equipment damage).

Do not place the device in extremely hot (refer to the specification

of the device for the detailed operating temperature), cold, dusty

or damp locations, and do not expose it to high electromagnetic

radiation. The appropriate temperature is -20℃to 65℃.

The device cover for indoor use shall be kept from rain and

moisture.

Exposing the equipment to direct sun light, low ventilation or heat

source such as heater or radiator is forbidden (ignorance can

cause fire danger).

Do not aim the device at the sun or extra bright places. A

blooming or smear may occur otherwise (which is not a

malfunction however), and affecting the endurance of sensor at

the same time.

Please use a soft and dry cloth when clean inside and outside

surfaces of the device cover, do not use alkaline detergents.

Please keep all wrappers after unpack them for future use. In case

of any failure occurred, you need to return the device to the

factory with the original wrapper. Transportation without the

original wrapper may result in damage on the device and lead to

additional costs.

Improper use or replacement of the battery may result in hazard

of explosion. Replace with the same or equivalent type only.

Dispose of used batteries according to the instructions provided

by the battery manufacturer.

Chapter 1 Preventive and Cautionary

Tips

To guarantee the card reader works properly, please read and

obey the notes below.

If the card reader is powered by the controller, the power

supply distance is recommended to be no longer than 100m.

If the distance is longer than 100m, you are advised to power

the card reader by external 12V (range: -%10 ~ +%10) DC

power supply, which is nonswitched and linear.

To guarantee the communication between the controller and

the card reader, you must use RVVP cable above 0.5 to

connect them.

If the card reader is installed outside or in environment easy

to permeable, it is advisable to install a waterproof shield.

If you need to install several card readers, the distance

among them must over 30cm.

To reduce the noise in long distance transmission, the shield

of cable should connect to the GND of both controller and

card reader terminal.

Chapter 2 Introduction

2.1 Front View

The front view of DS-K1801 series card reader is shown below:

DS-K1801M/DS-K1801E DS-K1801MK/DS-K1801EK

2.2 Side View and Rear View

The side view of card reader is shown below:

Side View Rear View

Chapter 3 Wiring and Installation

3.1 Terminal Description

The description of 8 cables is shown below.

Table 3-1 Description of Cable

Color

Description

Red

PWR (+12 VDC)

Black

GND

Purple

Beep Control

Brown

Orange

ERR

Green

Wiegand W0

White

Wiegand W1

Blue

Wiegand 26/ 34

3.2 Wiring Cables

Purpose:

Wire the cables between controller and card reader, thus to

establish the communication between them.

Steps for Wiegand communication mode:

Wiring the cable between controller and card reader as shown

below.

1. Set the Wiegand mode before power-on:

Cable

Wiring Method

Wiegand Mode

Blue Wiegand Cable

Grounded

Wiegand 26

Not Grounded

Wiegand 34

2. Wiring the cable between controller and card reader as

Altri manuali per DS-K1801 Series

Indice

Altri manuali HIK VISION Controllori di accesso IP

HIK VISION

HIK VISION DS-K1T804EF Manuale utente

HIK VISION

HIK VISION DS-K2601 Istruzioni operative e di manutenzione

HIK VISION

HIK VISION DS-K1T501 Manuale utente

HIK VISION

HIK VISION DS-K1T673-T Series Manuale utente

HIK VISION

HIK VISION DS-K1T105M Guida di sicurezza

HIK VISION

HIK VISION DS-K281X Series Manuale utente

HIK VISION

HIK VISION DS-K2600 Series Manuale utente

HIK VISION

HIK VISION UD06519B-A Manuale utente

HIK VISION

HIK VISION DS-K2600 Series Manuale utente

HIK VISION

HIK VISION DS-K1F600U-D6E Series Manuale utente

HIK VISION

HIK VISION DS-K5603-Z Manuale utente

HIK VISION

HIK VISION K1T604 Guida rapida

HIK VISION

HIK VISION DS-K281 Series Manuale utente

HIK VISION

HIK VISION MinMoe DS-K1T671TM-3XF Manuale utente

HIK VISION

HIK VISION DS-TME401-TPC Manuale utente

HIK VISION

HIK VISION DS-K1T804B Series Manuale utente

HIK VISION

HIK VISION UD22708B Manuale utente

HIK VISION

HIK VISION DS-K1T502 Series Manuale utente

HIK VISION

HIK VISION DS-PTA-WL-868 Manuale utente

HIK VISION

HIK VISION DS-K3M200 Manuale utente

HIK VISION

HIK VISION DS-K1T105 Series Manuale utente

HIK VISION

HIK VISION DS-K1T605 Series Manuale utente

HIK VISION

HIK VISION DS-K1TA70MI-T Manuale utente

HIK VISION

HIK VISION UD12126B-B Manuale utente

Manuali Controllori di accesso IP popolari di altre marche

ZKTeco

ZKTeco SpeedFace-V5L Manuale utente

Jantar

Jantar REX A-1-9 Manuale utente

2N Access Unit Foglio di istruzioni

Kedacom

Kedacom KSCA120 Series Manuale utente

H3C

H3C WX2880X Manuale utente

G4S

G4S S870-EX Guida

PRASTEL

PRASTEL M2000PE Manuale utente

Allegion

Allegion interflex IF-281 Cylinder Manuale utente

TECOM

TECOM TS1067E Manuale utente

Fermax

Fermax Memokey 100C Guida utente

Fermax

Fermax CITYLINE MEMOKEY Manuale di istruzioni

Software House

Software House iSTAR Pro 2U RM Manuale di istruzioni

AKCP

AKCP SP+ Manuale utente

Bpt

Bpt HNA/102 Manuale utente

Civintec

Civintec CV9601T-T-1F Manuale utente

BioMax

BioMax N-X90W Manuale utente

ZKTeco

ZKTeco OP-200 Manuale utente

FingerTec

FingerTec s-Kadex Manuale utente