HIK VISION HWT-T250-M Manuale utente
HD Turret and Bullet
Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to the
new version of this manual. We will readily improve or
update the products or procedures described in the
manual.
0100001080706
Regulatory Information
FCC Information
Please take attention that changes or modification not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European standards
listed under the Low Voltage Directive 2014/35/EU, the
EMC Directive 2014/30/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a
battery that cannot be disposed of as
unsorted municipal waste in the European
Union. See the product documentation for
specific battery information. The battery is
marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For
more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and
“Cautions”.
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.
Warnings
In the use of the device, you must be in strict
compliance with the electrical safety regulations of the
nation and region.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12
VDC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.
The output current of the power adapter must be no
more than 6A.
Do not connect multiple devices to one power adapter
to avoid over-heating or a fire hazard caused by
overload.
Make sure that the plug is firmly connected to the
power socket.
Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cord, and
then contact the service center.
Never attempt to disassemble the camera by
unprofessional personal.
Cautions
Do not drop the camera or subject it to physical shock.
Do not place the camera in extremely hot, cold (the
operating temperature shall be -40°C to 60°C), dusty or
damp locations, and do not expose it to high
electromagnetic radiation.
Do not touch senor modules with fingers.
If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty or damp
environment.
To avoid heat accumulation, good ventilation is
required for the operating environment.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Keep the camera away from liquid while in use for non-
water-proof device.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
Mark Description
Table 0-1 Mark Description
Mark Description
DC Voltage
1 Introduction
1.1 Product Features
The main features are as follows:
High performance CMOS sensor
IR cut filter with auto switch
OSD menu with configurable parameters
Auto white balance
Internal synchronization
SMART IR mode
3-axis adjustment
1.2 Overview
This manual applies to six types of cameras. The
overviews of each type are shown in the figures below.
1.2.1 Overview of Type I Camera
DC12VIN
Video Cable
Power Cord
12
VDC
Switch Button Mounting Base
Main Body
Enclosure
Figure 1-1 Overview of Type I Camera
Note:
Press and hold the switch button for 5 seconds to switch
the video output. Four kinds of video outputs are
available: TVI, AHD, CVI, and CVBS.
1.2.2 Overview of Type II Camera
DC12VIN
Enclosure
Main Body
Mounting
Base Video Cable
Switch Button
Power Cord
12 VDC
Figure 1-2 Overview of Type II Camera
Note:
批注
[KL1]:
海螺
14&
海螺
17 2
批注
[KL2]:
海螺
13 4
Press and hold the switch button for 5 seconds to switch
the video output. Four kinds of video outputs are
available: TVI, AHD, CVI, and CVBS.
1.2.3 Overview of Type III Camera
Figure 1-3 Overview of Type III Camera
Note:
Press and hold the switch button for 5 seconds to switch
the video output. Four kinds of video outputs are
available: TVI, AHD, CVI, and CVBS.
1.2.4 Overview of Type IV Camera
Figure 1-4 Overview of Type IV Camera
Note:
Press and hold the switch button for 5 seconds to switch
the video output. Four kinds of video outputs are
available: TVI, AHD, CVI, and CVBS.
1.2.5 Overview of Type V Camera
Figure 1-5 Overview of Type V Camera
Note:
Press and hold the switch button for 5 seconds to switch
the video output. Four kinds of video outputs are
available: TVI, AHD, CVI, and CVBS.
1.2.6 Overview of Type VI Camera
批注 [KL3]: 金属海螺 17 H0T 里是有的 3
批注 [KL4]: 金属海螺 13 5
批注 [KL5]: 筒机 22 6
批注 [KL6]: 筒机 32 7
Figure 1-6 Overview of Type VI Camera
Note:
Press and hold the switch button for 5 seconds to switch
the video output. Four kinds of video outputs are
available: TVI, AHD, CVI, and CVBS.
2 Installation
Before you start:
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched with your
power output to avoid the damage.
Make sure the wall is strong enough to withstand three
times the weight of the camera and the mount.
If the wall is cement, insert expansion bolts before
installing the camera. If the wall is wooden, use self-
tapping screws to secure the camera.
If the product does not function properly, contact your
dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.
2.1 Installation of Type I and Type II Camera
Before you start:
Type I and type II cameras share the same installation,
and we take type I camera as the example to describe the
installation method.
Both wall mounting and ceiling mounting are suitable for
the camera. We take ceiling mounting as an example in
this section. You can take the steps of ceiling mounting as
a reference, when adopting wall mounting.
Steps:
1. Disassemble the turret camera by rotating the camera
to align the notch to one of the marks, as shown in the
figure below.
Figure 2-1 Disassemble the Camera
2. Remove the mounting base from the camera body
with a flat object, e.g., a coin.
3. Paste the drill template (supplied) to the place where
you want to install the camera.
4. Drill the screw holes, and the cable hole (optional) on
the ceiling according to the drill template.
批注 [KL7]: 海螺 17&14, 海螺 13
Figure 2-2 Drill Template
Note:
Drill the cable hole, when adopting the ceiling outlet
to route the cable.
5. Attach the mounting base to the ceiling, and secure
them with supplied screws.
Figure 2-3 Attach the Mounting Base to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement ceiling, expansion bolts are required
to fix the camera. For wooden ceiling, self-tapping
screws are required.
6. Route the cables through the cable hole, or the side
opening.
7. Align the camera with the mounting base, and tighten
the screws to secure the camera on the mounting
base.
Figure 2-4 Secure the Camera with Mounting Base
8. Connect the corresponding cables, such as power
cord, and video cable.
9. Power on the camera to check whether the image on
the monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below to get
an optimum angle.
Figure 2-5 3-axis Adjustment
1). Hold the camera body and rotate the enclosure to
adjust the pan position [0° to 360°].
2). Move the camera body up and down to adjust the
tilt position [0° to 75°].
3). Rotate the camera body to adjust the rotation
position [0° to 360°].
2.2 Installation of Type III Camera
Before you start:
Both wall mounting and ceiling mounting are suitable for
the camera. We take ceiling mounting as an example in
this section. You can take the steps of ceiling mounting as
a reference, when adopting wall mounting.
Steps:
1. Disassemble the turret camera.
1). Use the screw driver to loosen the screw on the
mounting base.
2). Align the notch to the clip plate to separate the
mounting base from the camera body.
Figure 2-6 Disassemble the Camera
2. Paste the drill template (supplied) to the place where
you want to install the camera.
3. Drill the screw holes and the cable hole (optional) on
the ceiling according to the drill template.
Figure 2-7 Drill Template
Note:
Drill the cable hole, when adopting the ceiling outlet
to route the cable.
4. Attach the mounting base to the ceiling, and secure
them with supplied screws.
批注 [KL8]: 海螺 17 金属的安装，
Figure 2-8 Attach the Mounting Base to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement ceiling, expansion bolts are required
to fix the camera. For wooden ceiling, self-tapping
screws are required.
5. Route the cables through the cable hole, or the side
opening.
6. Combine the camera body with the mounting base.
1). Put the camera body in the mounting base.
2). Align the notch to the clip plate, and rotate the
enclosure a little bit.
3). Tighten the screw to secure the camera on the
mounting base.
Figure 2-9 Secure the Camera with Mounting Base
7. Connect the corresponding cables, such as power
cord, and video cable.
8. Power on the camera to check whether the image on
the monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below to get
an optimum angle.
Pan Position
[0° to 360°]
Rotation Position
[0° to 360°]
Tilt Position
[0° to 75°]
Figure 2-10 3-axis Adjustment
1). Rotate the enclosure to adjust the pan position [0°
to 360°].
2). Move the camera body up and down to adjust the
tilt position [0° to 75°].
3). Rotate the camera body to adjust the rotation
position [0° to 360°].
2.3 Installation of Type IV Camera
批注 [KL9]: 这句话要修改
批注 [KL10]: 海螺 13 全金属
Before you start:
Both wall mounting and ceiling mounting are suitable for
the camera. We take ceiling mounting as an example in
this section. You can take the steps of ceiling mounting as
a reference, when adopting wall mounting.
Steps:
1. Disassemble the turret camera by rotating the trim
ring anticlockwise to get the trim ring out of the
camera as shown in the figure below.
Figure 2-11 Get the Trim Ring out
2. Paste the drill template (supplied) to the place where
you want to install the camera.
Figure 2-12 Drill Template
Note:
Drill the cable hole, when adopting the ceiling outlet
to route the cable.
3. Attach the camera to the ceiling, and secure them
with supplied screws.
Figure 2-13 Attach the Camera to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement ceiling, expansion bolts are required
to fix the camera. For wooden ceiling, self-tapping
screws are required.
4. Route the cables through the cable hole, or the side
opening.
5. Put the trim ring back, and tighten it by rotating it
clockwise.
Questo manuale è adatto per i seguenti modelli
6
Indice
Altri manuali HIK VISION Telecamera di sicurezza
HIK VISION
HIK VISION UD04331B Manuale utente
HIK VISION
HIK VISION E-series Manuale utente
HIK VISION
HIK VISION HWI-T241H Manuale utente
HIK VISION
HIK VISION iDS-TCM403-A Manuale utente
HIK VISION
HIK VISION CMHT1823 Manuale utente
HIK VISION
HIK VISION UD02330B Manuale utente
HIK VISION
HIK VISION DS-2DF1-512 Manuale utente
HIK VISION
HIK VISION DS-2AF1-764 Manuale utente
HIK VISION
HIK VISION DS-2DE7A412MCG-EB Manuale utente
HIK VISION
HIK VISION DSHD21E2 Manuale utente
HIK VISION
HIK VISION UD.6L0201B1907A01 Manuale utente
HIK VISION
HIK VISION DS-2CE59H8T-(A)VPIT3ZF Manuale utente
HIK VISION
HIK VISION DS-2CE1512PN-IR Manuale utente
HIK VISION
HIK VISION DS-2CC5197P-VF Manuale utente
HIK VISION
HIK VISION DS-2DP8A440IXG-LEF/624(F0) Manuale utente
HIK VISION
HIK VISION ColorVu DS-2CE72DFT-FC Manuale utente
HIK VISION
HIK VISION DS-2AE714 Manuale utente
HIK VISION
HIK VISION DS-2TD8166-150ZH2F/V2 Manuale utente
HIK VISION
HIK VISION DS-2TD2608-2/QA/FP Manuale utente
HIK VISION
HIK VISION DS-2CD2063G0-I Manuale utente
