Hiland F600X Manuale utente

F600X Flash lamp user manual Version: A1

F600X Flash lamp user manual

I. Safety Instruction

1. For security, please read the user manual carefully before initial operation;

2. Please be sure the power is off before connecting, the product is produced without fuse;

3. This system must not endanger life or property during the running failure or its security risks have

been eliminated

II. Technical Specification

1. Working voltage：12-240VAC /DC

2. Loading capacity：<3W

3. Flicker Frequency：1HZ

4. Working temperature：-20º～+60℃

5．Size：φ86* 125mm

6. Weight: 83g

III. Connecting Instruction

1. Port CN1 is for connecting the power input, working voltage is 12-240VAC/DC

2. Port CN2 is for connecting the antenna to extend the effective distance of controller

IV. Instructions

4.1 LED will flicker in 1HZ after power on

4.2 JP1 switch

It’s the switch for switching LED in flickering or lighting,

When JP1 at flash, LED will flicker in 1Hz after power on;

When JP1 at No flash, LED will light after power on

Danger: The whole product including the LED is with high voltage when power on (Power off before open the case)

V. Installation

5.1 F6000 with bracket

2．Mark the 2 holes as it in picture

1．Open the package ,take out the

accessories and rotate the

antenna anticlockwise.

3．Drill two 6mm diameter holes and one 10mm

diameter hole. Then put the expansion tube into 6mm

diameter holes, put wire through 10mm diameter hole.

F600X Flash lamp user manual Version: A1

5.2 F6000 should be installed with bracket and perpendicular to the ground

The interpretation and ownership of this manual belong to Hiland company. Any change of the product can be without prior

notice

．

Connect the power and antenna

wires with terminals.

．

Put the power wire and antenna

through the hole of bracket, fix the

holder with TA4*30 screw on the wall

Put the power wire and antenna

through the hole of holder, fix the holder

on the bracket with PA4*10mm screws.

8．

Install the case, and make sure the

fastener fixed with the holder. Then

screw up the antenna clockwise.

7.扣上上盖，注意将灯罩托板的卡扣和底

座扣好，然后将天线顺时针方向拧紧。

User must install the lamp with bracket and

make the lamp perpendicular to the ground

Make sure the lamp not install slantwise

to avoid water gets inside the lamp

6. Make sure the Sealing ring

installed correctly into the Groove

on the holder.

9．Fit the cover case on the holder

without gap. And twist the antenna

until it’s getting tight

Indice

Altri manuali Hiland Luce esterna

Hiland

Hiland F5020 Manuale utente

Manuali Luce esterna popolari di altre marche

Sealey

Sealey LED37 Manuale utente

nordlux

nordlux VEJERS Guida utente

SImx

SImx ELITE LED LHTC637 Manuale utente

GEV

GEV CAROLINE 10833 Manuale utente

NEBO

NEBO NEB-LSP-0020 Manuale utente

WE-EF

WE-EF PFL540 LED Manuale utente

Lindby

Lindby 9949029 Manuale utente

HEPER

HEPER DOGO Side LW6048.585-US Istruzioni per l'installazione e il funzionamento

HEPER

HEPER LW8034.003-US Istruzioni per l'installazione e il funzionamento

Maretti

Maretti VIBE S 14.6080.04.A Manuale utente

BEGA

BEGA 84 253 Manuale

HEPER

HEPER MINIMO Istruzioni per l'installazione e il funzionamento

LIGMAN

LIGMAN BAMBOO 3 Manuale utente

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuale utente

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuale utente

urban ambiance

urban ambiance UQL1273 Manuale utente

TotalPond

TotalPond 52238 Manuale utente

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuale utente