Hills NX-1508 Manuale utente

HILLS®Series LED Code Pad

User Manual

Not all features may be available on your system

Check with your installer to find out which features are programmed

V2.02

Page 2

TABLE OF CONTENTS

•Code Pad Diagrams .......................................................................................2

•Glossary of Terms ..........................................................................................4

•Understanding the Code Pad Lights...............................................................5

•Code Pad Control Tones................................................................................6

•Fully arming the system – On Mode...............................................................7

•Fully arming the system – Quick Arm Mode...................................................7

•Partially arming the system – Partial Mode ....................................................8

•Disarming – from the On or Partial Mode.......................................................8

•Bypassing – Individual Zones.........................................................................9

•Group Bypass.................................................................................................10

•Changing & Adding User Codes.....................................................................11

•Deleting User Code ........................................................................................12

•Walk Test........................................................................................................12

•User Code Authorisation.................................................................................13

•Setting the Door Chime ..................................................................................13

•Exit Mode – Extend Exit Timer .......................................................................14

•Code Pad Emergency Keys............................................................................14

•Viewing Alarm Memory...................................................................................14

•Reset Latched Alarms ....................................................................................15

•Setting System Date.......................................................................................15

•Setting System Time.......................................................................................16

•Set Code Pad Tones ......................................................................................16

•Program Telephone Number..........................................................................17

•Viewing Telephone Numbers..........................................................................18

•Cancelling Alarm Calls....................................................................................18

•Deleting Telephone Numbers.........................................................................19

•Communicator, Battery & Siren Test..............................................................19

•Service Light...................................................................................................20

•Emergency Evacuation Plans.........................................................................21

•Zone

List.........................................................................................................Back Page

V2.02

Page 3

GLOSSARY OF TERMS

Authority Level: The level of access an individual has when using an alarm panel.

Central Station: Location where alarm data is sent during an alarm report.

Chime Feature: An option that allows the code pad to sound a ding-dong whenever an

entry/exit door is opened.

Codes: Can be either User Codes (relating to a person) or Function Codes (a toggle switch to

turn specific functions on/off). NOTE: A system may have either 99 four (4) digit codes or 66

six (6) digit codes, but not a mixture of the two.

Dialer Delay: An option that allows a delay in reporting to the central station.

Duress Code: An option that allows a special code to be sent to the central station that

indicates the alarm system is being operated under duress.

Forced Arming:

An option that allows the system to be turned on (ARMED) with one or more zones open. A

system that is ready to be “force armed” will flash the ready light. (Note: Those zones that are

not ready will not create an alarm.)

Function Code: A Function Code is either a four (4) or six (6) digit code that has been

programmed by the installer to operate a device.

Group Bypass: An option that allows the user to bypass multiple zones with a single

operation.

Master Code: A master PIN code that can arm & disarm the alarm system, and can add and

delete user PIN codes.

Partial Arm: A mode used to arm the perimeter and unused areas of an occupied premises.

Perimeter: The outer edge of the protected area, typically the windows and doors fitted with

alarm sensors.

Quick Arm: An option that allows you to turn on (ARM) the security system by pressing either

the [ON] or [PARTIAL] key on the code pad control (for ARMING only) as programmed by the

installing company.

Universal Arming (Uni Arm): When enabled, your alarm system can automatically determine

whether to arm in the Full mode or in the pre-set Partial mode by looking to see if you exit your

premises or stay inside after arming your system. NOTE: This feature can be used in

conjunction with “Quick Arm”.

User Code: A four (4) or six (6) digit entry used to arm or disarm the system.

V2.02

Page 4

UNDERSTANDING THE LIGHTS

Armed Light

The armed light is “on” when the system is armed. The armed light is “off” when it is disarmed.

The armed light will flash when there has been an alarm during the previous arm cycle.

Bypass Light

The bypass light is “on” when any zone in this code pad’s area is bypassed. The zone(s) that is

bypassed will also be illuminated. If the bypass light is “off”, no zones are bypassed.

Chime Light

The chime light is “on” when the chime feature is “on”; “off” otherwise.

Exit Light

The exit light is “on” during the exit delay. Please note that the light will flash during the last 10

seconds of the exit delay as a warning that the time is running out. (The user may want to

restart the exit delay if the exit light is flashing in order to prevent an alarm. The user may then

press the [Exit] key to restart the exit delay before the delay expires.)

Fire Light

A steady fire light means a fire zone has been faulted. A rapidly flashing fire light means that a

fire zone is in a trouble condition.

On Light

The on light is “on” when the system is armed. The on light is “off” when it is disarmed.

Partial Light

The partial light is “lit” when the system is armed in the Partial Mode. All non bypassed zones

will be delayed and follow the Partial delay time. When armed in Partial Mode, the Arm, On,

and Bypass lights will also be “lit”.

Power Light

The power light is lit if the primary power is on. The power light will flash if the system detects a

low battery condition.

Ready Light

The ready light is “lit” when the system is ready to arm and “flashes” if ready to force arm. The

ready light is off when the system is not ready to arm because of a zone(s) being faulted.

Zone Light

The zone lights are “off” when everything is normal. A zone light will be “lit” if the zone has

been bypassed. If a zone light is “flashing”, that zone is in alarm or has been faulted. If a zone

light is “flashing” rapidly, it means that the zone is in a trouble condition. Trouble conditions

are: Hardwire Zone Tamper; Wireless Zone Tamper, Sensor Low Battery and Sensor

Loss of Supervision

(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid “flashing” light for a

short period of time, followed by a slow “flashing” light.)

V2.02

Page 5

CODE PAD CONTROL TONES

•Beeps for all key presses Sounds a continuous tone during the entry delay time.

•Pulses when a day zone is violated while the system is disarmed.

•Pulses when a fire zone has a trouble condition.

•Beeps 3 times for trying to arm with the “Ready” light off, if “Force Arming” has not been

selected.

•Beeps for 1 second or emits a “ding-dong” sound for the “Chime” feature.

•Beeps during an exit delay; beeps rapidly for the last 10 seconds of an exit delay; and

beeps 1 second at the end of the exit delay.

•Pulses when the armed status changes and the AC power is off.

•Pulses when the armed status changes and any zone(s) is bypassed.

•Pulses when the armed status changes and a low battery is detected.

•Pulses when the armed status changes and a tamper condition is detected. Beeps to

indicate telephone line cut, if selected.

•Pulses when one or more of the following conditions are detected: zone or box tamper,

low battery, AC power fail, or expander trouble.

Entering a valid code will silence the code pad sounder when it is pulsing. Please

contact your installer if a trouble condition exists.

V2.02

Page 6

FULLY ARMING THE SYSTEM – ON MODE

ON is used when the user is away from the premise and wants the interior protected. To arm

in the ON Mode:

Close all protected doors and windows. Ready light will light when all protected zones and

sensors are secure. NOTE: If any zones are bypassed, a sensor in that zone can be violated

without affecting the ready light. The security system will not arm if the ready light is not on. If

the power light is off, you have no AC power. Restore power if possible. If not, contact your

installation company.

Enter your 4 digit user code to arm the system. The armed and exit lights will illuminate. You

may now leave the building via the designated exit path.

Note: The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to

the user that the exit time is about to expire.

Key Sequence Operation

Example shows a User code of 1234

being used to set the system to the

ON Mode.

FULLY ARMING THE SYSTEM – QUICK ARM MODE

Quick Arm is used when the person arming the alarm system does not have a user code, is

leaving the premises and wants the interior protected. To arm in the Quick Arm Mode:

Close all protected doors and windows. Ready light will light when all protected zones and

sensors are secure. NOTE: If any zones are bypassed, a sensor in that zone can be violated

without affecting the ready light. The security system will not arm if the ready light is not on. If

the power light is off, you have no AC power. Restore power if possible. If not, contact your

installation company.

The [ON] key to arm the system. The armed and exit lights will illuminate. You may now

leave the building via the designated exit path.

Note: The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to

the user that the exit time is about to expire.

Key Sequence Operation

Example shows ON key being used

to set the system to the Quick Arm

Mode.

V2.02

Page 7

PARTIALLY ARMING THE SYSTEM – PARTIAL MODE

Partial arming allows you to temporarily exclude some rooms from security arming. For

example, you may wish to exclude bedrooms at night when they are in use. Partial mode is

also used for protecting exterior doors and windows (the home perimeter) when the user is

inside.

Partial is used when the user is inside the premise and wants protection around the

perimeter. Listed below are the steps to arm in the Partial mode:

Close all protected doors and windows. Ready light will light when all protected zones and

sensors are secure. NOTE: If any zones are bypassed, a sensor in that zone can be violated

without affecting the ready light. The security system will not arm if the ready light is not on. If

the power light is off, you have no AC power. Restore power if possible. If not, contact your

installation company.

Press the [PARTIAL] key. The bypass light will illuminate if any zone(s) is bypassed. The

light(s) corresponding to the bypassed zone(s) will illuminate, alerting the user that a zone(s)

may be unprotected and can be faulted without an alarm.

Key Sequence Operation

Press the Partial key to partially arm

your premises

PARTIAL

DISARMING – FROM THE ON OR Partial MODE

When you enter the protected area through one of the designated Entry/Exit doors, the code

pad control will sound a solid continuous tone for the duration of the entry delay time, or until

you enter a valid code. After entering a valid code the red armed light will go off and the tone

will stop. The security system is now DISARMED. If a valid code is not entered before the

end of the entry delay, an alarm will occur. (NOTE: If the red armed light is flashing during

the entry delay, the alarm system has been activated in your absence. Leave the building

immediately and call your alarm company and/or the police from a safe location.)

Key Sequence Operation

Enter your user code to disarm the

system from the On or Partial mode.

V2.02

Page 8

BYPASSING – INDIVIDUAL ZONES

Bypassing is used to temporarily exclude one or more zones that would normally be

protected. For instance, a pet may need to be left in a part of the house that is usually

protected. If you wish to bypass one or more zones, this must be done while the system is in

the disarmed state. The following steps are used for bypassing zones. Once you have

Bypassed the zone(s) you may Arm the system via the ON or PARTIAL Mode. When your

security system is disarmed, any zones that has been temporarily isolated or bypassed will

be reset, and will therefore be protected when the system is armed again. To manually un-

bypass zones, perform the bypassing procedure on a zone that is already bypassed.

The corresponding light for that zone will go off when un-bypassed.

Key Sequence Operation

This example shows a user

bypassing zones 4 and 5.

1. Press the [BYPASS] key.

(The bypass light flashes.)

Tick box if User code required

2. Enter a 2-digit zone indicating the

zone you wish to bypass.

(Example: Press the [0][4] keys for

zone 4, press [0][5] keys for zone 5.)

The corresponding light for that zone

will turn on when bypassed.

3. Press the [BYPASS] key again.

NB: Pleased check with your security

installation company to determine if a

user code is required to bypass

zones. If this feature has been

enabled you will be required to enter

a valid user code after step 1., and

before step 2.

BYPASS

V2.02

Page 9

GROUP BYPASS

By pressing the [BYPASS] key, followed by the [0][0] key, then the [BYPASS] key again, all

zones that are designated as group bypass zones will be bypassed. Now you can arm your

system in either the [ON] or [PARTIAL] mode. Once armed pressing the [BYPASS] key

again will toggle the bypassed zones on and off.

Key Sequence Operation

1. Press the [BYPASS] key.

(The bypass light flashes.)

Tick box if User code required

2. Press [0][0] keys. The group

bypass zone lights will turn on when

bypassed.

3. Press the [BYPASS] key again.

NB: Pleased check with your security

installation company to determine if a

user code is required to group

bypass. If this feature has been

enabled you will be required to enter

a valid user code after step 1., and

before step 2.

V2.02

Page 10

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hills Tastiera

Hills

Hills Series LCD Code Pad Manuale utente

Hills

Hills HILLS series Manuale utente

Hills

Hills NX Series Manuale utente

Hills

Hills NX-1516 Manuale utente

Hills

Hills Series LCD Code Pad Manuale utente

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo