Hitachi 8000 Series Manuale utente

Introduction

Part names

• Any button marked with “*” is not supported on this projector (User's

Manual (detailed)119).

• Each time you press any button (except ID buttons), the ID button of current

selected ID number will light (User's Manual (detailed)17).

NOTE

Back of

the remote control

Remote control

(1) STANDBY button (2)

(2) ON button (2)

(3) ID - 1 / 2 / 3 / 4 buttons (3)

(4) INPUT PORTS button (3)

(5)

PAGE UP / PAGE DOWN buttons

(4)

(6) F5 button (4)

(7) ENTER button

(8) RESET button

(9) ESC button (4)

(10) ▲/▼/◄/►cursor buttons

(11) MENU button (5)

(12) VOL + / - buttons (6)

(13) AV MUTE button (6)

(14) MAGNIFY ON / OFF buttons (7)

(15) FREEZE button (8)

(16) PbyP button (9)

(17) ASPECT button (10)

(18) AUTO button (11)

(19) POSITION button (11)

(20) KEYSTONE button (12)

(21) MY BUTTON - 1, 2, 3, 4 buttons (13)

(22) FOCUS + / - buttons (14)

(23) ZOOM + / - buttons (14)

(24) LENS SHIFT button (14)

(25) LENS MEMORY button (15)

(26) Battery cover (16)

(27) Wired remote control port (17)

(1)

(4)

(5)

(15)

(6)

(7)

(8)

(9)

(21)

(19)

(20)

(2)

(12)

(14)

(13)

(10)

(11)

(18)

(24)

(26)

(25) (23)

(22)

(16) (17)

(27)

1. Make sure that the power cord is rmly

and correctly connected to the projector

and the outlet.

Turning on the power

2. Make sure that the POWER indicator is

lighted in steady orange (User's Manual

(detailed)120). Then remove the lens

cover.

Press STANDBY/ON button on the projector

or the ON button on the remote control.

The projection lamp will light up and POWER indicator will begin blinking in

green. When the power is completely on, the indicator will stop blinking and

light in steady green (User's Manual (detailed)120).

Power on/off button

To display the picture, select an input signal according to the section Selecting an

input signal (User's Manual (detailed)26).

►A strong light is emitted when the projector’s power is on.

Do not look into the lens of the projector or look inside of the projector through

any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just

after use, since it is too hot.

WARNING

1. Press the STANDBY/ON button on the projector or the STANDBY button on

the remote control.

The message “Power off?” will appear on the screen for about 5 seconds.

Turning off the power

2. Press the STANDBY/ON or STANDBY button again while the message

appears.

The projector lamp will go off, and the POWER indicator will begin blinking

in orange. Then the POWER indicator will stop blinking and light in steady

orange when the lamp cooling is complete (User's Manual (detailed)120).

3. Attach the lens cover, after the POWER indicator turns to steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off.

Also, do not turn the projector off shortly after turning it on. Such operations might

cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

Remote control

POWER indicator

ON button

STANDBY button

STANDBY/ON button

ID button

INPUT PORTS button

Remote control

Using the REMOTE ID function

Utilize this function to control speci c projectors by the remote

control assigned the same ID number when you use multiple

projectors of the same type at the same time.

Assign an ID number to each projector before using the

REMOTE ID item in the SERVICE menu of the OPTION menu

(User's Manual (detailed)74). Press the ID button with the

same ID number as assigned to the projector you are going to

control. The ID button selected will light for several seconds.

• Each time you press any button (except ID buttons), the ID button of

current selected ID number will light.

• To con rm the projector's current ID, press any ID button for 3 seconds. Its

number will be shown on each screen regardless of set ID of projector.

NOTE

ID buttons

Selecting an input signal

1. Press COMPUTER 1 / 2, LAN, USB TYPE A / B, HDMI 1 / 2, COMPONENT,

S-VIDEO or VIDEO button on the remote control.

The port corresponding to each button is selected as below.

Button Ports

COMPUTER 1 COMPUTER IN1

COMPUTER 2 COMPUTER IN2

LAN LAN

USB TYPE A USB TYPE A

USB TYPE B USB TYPE B

HDMI 1 HDMI 1

HDMI 2 HDMI 2

COMPONENT COMPONENT

S-VIDEO S-VIDEO

VIDEO VIDEO

Buttons for input

ports

• While ON is selected for AUTO SEARCH item in OPTION menu,

the projector will keep checking every port sequentially till an input signal is

detected (User's Manual (detailed)68).

• It may take several seconds to project the images from the USB TYPE B port.

NOTE

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple

mouse and keyboard of the computer, when the

projector’s USB TYPE B port and the computer’s

type A USB port are connected and MOUSE is

selected for the USB TYPE B item in the OPTION

menu (User's Manual (detailed)70).

(1) PAGE UP key: Press PAGE UP button.

(2) PAGE DOWN key: Press PAGE DOWN button.

(3) Mouse left button: Press ENTER button.

(4) Move pointer: Use the cursor buttons

▲, ▼, ◄ and ►.

(5) ESC key: Press ESC button.

(6) Mouse right button: Press RESET button.

(7) F5 key: Press F5 button.

►Improper use of the simple mouse &

keyboard function could damage your equipment.

While using this function, please connect this

product only to a computer. Be sure to check your

computer’s manuals before connecting this product

to the computer.

NOTICE

Remote control

(1)

(3)

(6)

(2)

(4)

(5)

(7)

USB TYPE B

port

PAGE UP / PAGE DOWN button

Operating

MENU button

1. To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after

powered on.

Using the menu function

2. (1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED

MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

This projector has the following menus:

PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK,

SECURITY and EASY MENU.

EASY MENU consists of functions often used, and the other menus are classi ed

into each purpose and brought together as the ADVANCED MENU.

Each of these menus is operated using the same methods. While the projector

is displaying any menu, the MENU button on the projector works as the cursor

buttons. The basic operations of these menus are as follows.

In the EASY MENU

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select

the EASY MENU.

The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the

▲/▼ cursor buttons to select an item to operate and press the ► cursor

button or ENTER button to progress. The operation menu or dialog of the

selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

In the ADVANCED MENU

button

RESET button

ENTER button

ESC button

Cursor buttons

INPUT

button

Remote control

Operating

VOL + / - button

AV MUTE button

Adjusting the volume of audio output

Use the VOL + / - buttons to adjust the volume.

A dialog will appear on the screen to aid you in

adjusting the volume. If you do not do anything,

the dialog will automatically disappear after a few

seconds.

•

When is selected for current picture input port, the volume

adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (

User's

Manual (detailed)

59).

• Even if the projector is in the standby mode, the volume is adjustable when

both of the following conditions are true:

- An option other than is selected for AUDIO OUT STANDBY in the AUDIO

SOURCE item of the AUDIO menu (User's Manual (detailed)59).

- NORMAL is selected in the STANDBY

MODE item of the SETUP menu

(User's

Manual (detailed)58).

1. Press AV MUTE button on the remote control.

The BLANK screen will be displayed instead of

the screen of input signals and the sound from the

AUDIO OUT port will be muted. Please refer to the

BLANK item in SCREEN menu about the BLANK

screen (User's Manual (detailed)60).

To exit from the AV MUTE mode and restore the screen and audio, press AV

MUTE button again.

►If you wish to have a blank screen while the projector's lamp is

on, use the AV MUTE function above or the lens shade function (User's Manual

(detailed)36). Taking any other action may cause the damage on the projector.

CAUTION

VOL + / -

buttons

AV MUTE

button

NOTE

Temporarily turning off the screen and audio output

• The projector automatically exits from the AV MUTE mode when

some control buttons are pressed.

• The projector is not equipped with an internal speaker. The audio is output

from the external audio system connected to the AUDIO OUT port.

Remote control

Operating

Using the magnify feature

Press the MAGNIFY ON button on the remote

control.

The picture will be magnied, and the MAGNIFY

dialog will appear on the screen. When the

MAGNIFY ON button is pressed for the rst time

after the projector is turned on, the picture will be

zoomed by 1.5 times. On the dialog, triangle marks

to show each direction will be displayed.

The display magnication of the projector switches in order

with every press of the MAGNIFY ON button.

For computer signals, HDMITM (RGB) signals, input signals from the

LAN, USB TYPE A or USB TYPE B ports

1.5 times  2 times  3 times  4 times  1 time

For video signals, s-video signals, component video signals or

HDMITM (Component) signals

1.5 times  2 times  1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

Press the MAGNIFY OFF button on the remote control to exit magnication.

MAGNIFY

ON / OFF

buttons

MAGNIFY ON / OFF button

Remote control

Operating

1. Press the SHADE button on the control panel.

The mechanical lens shade closes and the

screen turns to black. The SHADE indicator on

the projector blinks in yellow while the shade is

closed.

To open the shade and restore the screen, press

the SHADE button again.

Temporarily shading the screen

1. Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen

(however, the indication will not appear when the OFF

is selected for the MESSAGE item in the SCREEN

menu (User's Manual (detailed)63), and the

projector will go into the FREEZE mode, which the

picture is frozen.

To exit the FREEZE mode and restore the screen to normal, press the

FREEZE button again.

Temporarily freezing the screen

►If you wish to have a blank screen while the projector's lamp is

on, use the lens shade function above or the AV MUTE function (User's Manual

(detailed)25). Taking any other action may cause the damage on the projector.

CAUTION

FREEZE

button

SHADE

button

• The projector automatically exits from the FREEZE mode when some

control buttons are pressed.

• If the projector continues projecting a still image for a long time, the LCD

panel might possibly be burned in. Do not leave the projector in the FREEZE

mode for too long.

• Images might appear degraded when this function is operated, but it is not a

malfunction.

NOTE

FREEZE button

Remote control

Operating

The PbyP / PinP is a function for displaying two different picture signals on a

screen that is separated into main and sub areas for each signal.

PbyP (Picture by Picture) / PinP (Picture in Picture)

PbyP

button

Normal mode PbyP mode

main

area

sub

area

PinP mode

Press the PbyP button on the remote control. This acctivates the PbyP mode.

Then, press the PbyP button again. The projector goes into PinP mode. The

screen displayed before the PbyP button was pressed will be displayed as the

main area. Most of operations are effective for the main area only. Only outputs

the audio input signal paired with the picture input signal for the main area.

To quit the PinP mode, press the PbyP button again.

ðð

main

area

sub area

PbyP button

Remote control

Operating

ASPECT button

Selecting an aspect ratio

For a computer signal

CP-X8170:

NORMAL  4:3  16:9  16:10

CP-WX8265, CP-WU8460:

NORMAL  4:3  16:9  16:10  NATIVE

 For a video signal, s-video signal or component video signal

CP-X8170:

4:3  16:9  14:9

CP-WX8265, CP-WU8460:

4:3  16:9  16:10  14:9  NATIVE

 For an input signal from the LAN, USB TYPE A or USB TYPE B ports, or

if there is no signal

CP-X8170: 4:3 (xed)

CP-WX8265, CP-WU8460: 16:10 (xed)

1. Press ASPECT button on the remote control.

Each time you press the button, the projector switches

the mode for aspect ratio in turn.

For an HDMITM signal

CP-X8170:

NORMAL  4:3  16:9  16:10  14:9

CP-WX8265, CP-WU8460:

NORMAL  4:3  16:9  16:10  14:9  NATIVE

ASPECT

button

• ASPECT button does not work when no proper signal is inputted.

• NORMAL mode keeps the original aspect ratio setting.

NOTE

Remote control

Indice

Altri manuali Hitachi Proiettore

Hitachi

Hitachi CP-X1200 Series Manuale utente

Hitachi

Hitachi CP-A352WNM Manuale utente

Hitachi

Hitachi CP-A220N Manuale utente

Hitachi

Hitachi CP-DX300 guide Guida all'installazione

Hitachi

Hitachi CP-D32WN Manuale utente

Hitachi

Hitachi CPX10WN Manuale utente

Hitachi

Hitachi CP-A220N Manuale utente

Hitachi

Hitachi CP-X10000 Series Manuale utente

Hitachi

Hitachi CP-S225WA Manuale utente

Hitachi

Hitachi CP-X275WT Manuale utente

Hitachi

Hitachi CP-X2510Z and Documento tecnico

Hitachi

Hitachi CP-X5022WN Manuale utente

Hitachi

Hitachi CP-S317 Manuale utente

Hitachi

Hitachi CP-A200 Manuale utente

Hitachi

Hitachi Innovate CP-RX78 Manuale utente

Hitachi

Hitachi CP-X2514WN Manuale utente

Hitachi

Hitachi CP-X443 series Documento tecnico

Hitachi

Hitachi CP-X608 Documento tecnico

Hitachi

Hitachi ED-X22 Manuale utente

Hitachi

Hitachi CP-X1200 Series Manuale utente

Hitachi

Hitachi CP-SX1350 Series Manuale utente

Hitachi

Hitachi CP-X201 Manuale utente

Hitachi

Hitachi CP-X2020 Manuale utente

Hitachi

Hitachi CP-A222WN Manuale utente

Manuali Proiettore popolari di altre marche

iEmmet

iEmmet MP-312 Manuale utente

Epson

Epson VS400 Manuale utente

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuale utente

Sony

Sony VPL-HW65ES Manuale di servizio

Toshiba

Toshiba TLP-791U Manuale utente

Philips

Philips LC1341 Guida di riferimento

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuale utente

NEC

NEC NP600S EDU Manuale utente

BenQ

BenQ SH753P Manuale utente

Eiki

Eiki EK-623U series Manuale utente

Epson

Epson PowerLite Pro Cinema 6020UB Manuale utente

Epson

Epson PowerLite Home Cinema 705HD Manuale utente

Christie

Christie LHD700 Manuale utente

Navitar

Navitar FX Manuale utente

InFocus

InFocus LitePro 560 Manuale utente

Sony

Sony SRX-R815P Manuale utente

Vivitar

Vivitar DP1500 X Manuale utente

Acer

Acer C20 Series Manuale utente