Hitachi SPX-RCK5 Manuale utente
– 1 –
ENGLISH
DEUTSCH
FRANÇAISITALIANOESPAÑOL
PORTUGUÊS
∂ÏÏËÓÈο
MODEL
SPX-RCK5
Hr.
WIRED REMOTE CONTROLLER
– 2 –
PRECAUTIONS FOR USE
●In case of power failure happen, Wired Remote Controller will show current operating mode when power
comes back and continue to operate at previous setting mode.
●It is not recommended to use both Wireless Remote Controller and Wired Remote Controller at the same
time.
●Some features of Wireless Remote Controller are not available when use Wired Remote Controller as mentioned
below:
●Auto Mode
●Auto Mode
●Extended Airflow
●Auto Mode
●Parallel Swing Control
●Symmetry Swing Control
●Auto Mode
●Extended Airflow
●Plasma Ion Control
Standard Wireless Remote Controller Features not available on Wired Remote Controller
RAR-3U1
RAR-3U2
RAR-3U3
RAR-3U4
– 3 –
ENGLISH
NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT
■This controls the operation function and timer setting of the room air conditioner.
Precautions for Use
●Do not put the remote controller in the following places.
●Under direct sunlight.
●In the vicinity of a heater.
●Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.
●Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power
switch off and on or unplug the power cord and plug it in again).
This is to protect the device and does not indicate a failure.
●If you press the FUNCTION selector button during operation, the device may stop for about
3 minutes for protection.
START/STOP Button
Press this button to start operation.
Press it again to stop operation.
OPERATION LAMP
FUNCTION Button
Use this button to select the
operating mode. Every time you
press it, the mode will change from
(AUTO) to (HEAT) to
(DEHUMIDIFY) and to (COOL)
cyclically.
SLEEP Button
Use this button to set the sleep
timer. ( Page 9)
Reserve Button
Timer setting reservation.
OFF TIMER Button
Select the turn OFF time.
ON TIMER Button
Select the turn ON time.
Transmission Sign
The transmission sign blinks
when a signal has been sent.
TEMPERATURE Button
Room temperature setting.
Value will change quicker when keep
pressing.
RESET Button
FAN SPEED Button
This determines the fan speed.
Every time you press this button,
the intensity of circulation will
change from (AUTO) to (HI)
to (MED) to (LOW) to
(SILENT) (This button allows selecting
the optimal or preferred fan speed for
each operation mode).
AUTO SWING Button
Adjustment of the conditioned air in
the upward and downward directions.
CANCEL Button
Cancel timer reservation.
Hr.
– 4 –
VARIOUS FUNCTIONS
■Auto Restart Control
●If there is a power failure, operation will be automatically restarted when the power is resumed with
previous operation mode.
(As the operation is not stopped by remote controller.)
●If you intend not to continue the operation when the power is resumed, switch off the power supply.
When you switch on the circuit breaker, the operation will be automatically restarted with previous operation
mode.
Note: 1. If you do not require Auto Restart Control, please consult your sales agent or OFF by remote
control.
2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.
– 5 –
ENGLISH
HEATING OPERATION
●Use the device for heating when the outdoor temperature is under 21°C.
When it is too warm (over 21°C), the heating function may not work in order to protect the device.
●In order to keep reliability of the device, please use this device above -15°C of the outdoor temperature.
Press the FUNCTION selector so that the display indicates
(HEAT).
Set the desired FAN SPEED with the (FAN SPEED) button
(the display indicates the setting).
(AUTO) : The fan speed is HI at first and varies
to MED automatically when the preset
temperature has been reached.
(HI) : Economical as the room will become warm
quickly.
But you may feel a chill at the beginning.
(MED) : Fan speed slow.
(LOW) : Fan speed slower.
(SILENT) : Fan speed ultra slower.
Set the desired room temperature with the TEMPERATURE
buttons (the display indicates the setting).
The temperature setting and the actual room temperature may
vary somewhat depending on conditions.
Press the (START/STOP) button. Heating operation starts
with a beep. Press the button again to stop operation.
■As the settings are stored in memory in the remote controller, you only
have to press the (START/STOP) button next time.
1
2
3
START
STOP
– 6 –
DEHUMIDIFYING OPERATION
Use the device for dehumidifying when the room temperature is over 16°C.
When it is under 15°C, the dehumidifying function will not work.
■Dehumidifying Function
When the room temperature is higher than the temperature setting: The device will dehumidify the room,
reducing the room temperature to the preset level.
When the room temperature is lower than the temperature setting: Dehumidifying will be performed at
the temperature setting slightly lower than the current room temperature, regardless of the temperature
setting. The function will stop (the indoor unit will stop emitting air) as soon as the room temperature
becomes lower than the setting temperature.
Set the desired room temperature with the TEMPERATURE
button (the display indicates the setting).
The range of 20-26˚C is recommended as
the room temperature for dehumidifying.
Press the (START/STOP) button. Dehumidifying operation
starts with a beep. Press the button again to stop operation.
2
■As the settings are stored in memory in the remote controller, you
only have to press the (START/STOP) button next time.
START
STOP
Press the FUNCTION selector so that the display indicates
(DEHUMIDIFY).
The FAN SPEED is set at LOW or SILENT.
1
– 7 –
ENGLISH
COOLING OPERATION
Use the device for cooling when the outdoor temperature is
–
10~43°C.
If indoor humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.
Press the FUNCTION selector so that the display indicates
(COOL).
Set the desired FAN SPEED with the (FAN SPEED) button
(the display indicates the setting).
(AUTO) : The FAN SPEED is HI at first and varies
to MED automatically when the preset
temperature has been reached.
(HI) : Economical as the room will become cool
quickly.
(MED) : Fan speed slow.
(LOW) : Fan speed slower.
(SILENT) : Fan speed ultra slower.
Set the desired room temperature with the TEMPERATURE
button (the display indicates the setting).
The temperature setting and the actual room temperature may
vary some how depending on conditions.
Press the (START/STOP) button. Cooling operation starts
with a beep. Press the button again to stop operation. The
cooling function does not start if the temperature setting is
higher than the current room temperature (even though the
(OPERATION) lamp lights). The cooling function will start
as soon as you set the temperature below the current room
temperature.
■As the settings are stored in memory in the remote controller, you
only have to press the (START/STOP) button next time.
1
2
START
STOP
3
– 8 –
TIMER RESERVATION
■ON Timer and OFF Timer are available.
1OFF TIME setting
●Select the OFF TIME by pressing the (OFF)
Button.
●Setting time will change according to the below
sequence when you press the button.
●The value change quicker if you keep pressing the
button.
OFF Timer Reservation ■Operation stop at setting time
2Press the (Reserve) button
●OFF TIMER reserved with a signal received sound
“beep”.
●The (OFF) Mark starts lighting instead of blinking.
1ON TIME setting
●Select the ON TIMER by pressing the (ON) Button.
●At the beginning of setting, time 6 hours was set.
●Setting time will change according to the below
sequence.
●The value change quicker if you keep pressing the
button.
ON Timer Reservation
1Press the (Cancel) button
●As the time settings are stored in remote controller
memory, you only have to press the (Reserve)
button in order to use the same setting next time.
CANCELLATION of Timer Reservation
2Press the (Reserve) button
●ON TIMER reserved with a signal received sound
“beep”.
●The (ON) Mark starts lighting instead of blinking.
■Operation will start for setting
temperature at setting time (The starting
time may different depend on the room
temperature and set temperature).
Hr.
Hr.
Hr.
Hr.
– 9 –
ENGLISH
HOW TO SET THE SLEEP TIMER
Mode
Sleep timer
Indication
1 hour 2 hours 3 hours 7 hours
Sleep timer off
44 44
1
Sleep Timer: The device will continue working for the designated
number of hours and then turn off.
Press the SLEEP button, indoor unit will produce a beep.
The timer information will be displayed on the remote controller.
How to Cancel Reservation
Press the (CANCEL) button. The (RESERVED) sign goes out with a beep.
Example: Setting 3 hours
sleep time.
Hr.
Explanation of the sleep timer
The device will control the FAN SPEED and room temperature automatically so as to be quiet and good
for people’s health.
●If you set the sleep timer after the off or on-timer has been set, the sleep timer becomes effective
instead of the off or on-timer set earlier.
●You can not set other timer during sleep timer operation.
●After sleep timer time is up and when press sleep button again, the sleep timer will be set as
last setting.
●Sleep timer effective only once.
NOTE
– 10 –
INSTALLATION OF WIRED REMOTE CONTROLLER
1. When connecting the wires via the wall’s recessed
slot;
Fix the bottom casing to the wall by provided screw.
Assemble the top casing to the fixed bottom casing.
(Refer to the illustration below for detail installation)
Lead wires (3 strands)
are inserted through and
fastened via a rib-clip
Location of wall
mounting screw
Lead wires
connector Wires
Wires
Lead wires
connector
Wall recessed wiring installation (Supplied)
Wall mounting screws (2 pieces to
be used) (provided)
Inside top wiring installation (Alternative)
Wires
Wires
Lead wires
(3 strands)
Lead wires
connector
Wiring installation illustrations
2. When the wires to be connected from the inside top portion of top casing;
Break off a perforated aperture located at the top portion of the bottom
casing by nipper. Smoothen the aperture by cutter.
Fix the bottom casing to the wall by provided screw.
Connect the wires to the lead wires connector.
Mount the wires through the provided slot on top casing.
Assemble the top casing to the fixed bottom casing
(Refer to the illustration below for detail installation)
Wall
mounting
screws
(2 pieces)
(provided)
Indice
Lingue:
Altri manuali Hitachi Telecomando
Hitachi
Hitachi SPX-RCK2 Manuale utente
Hitachi
Hitachi PC-ART Manuale utente
Hitachi
Hitachi PC-ARFHE Manuale utente
Hitachi
Hitachi ECO COMPACT Manuale utente
Hitachi
Hitachi CIW03-H Manuale di istruzioni
Hitachi
Hitachi RAR-5F1 Manuale utente
Hitachi
Hitachi RAR-6NE2 Manuale utente
Hitachi
Hitachi airPoint Room700 Manuale utente
Hitachi
Hitachi PC-P5H Manuale utente
Hitachi
Hitachi RC-AGU1EA0G Manuale utente
Hitachi
Hitachi RC-AGU1EA0G Manuale utente
Hitachi
Hitachi PC-LH3A Manuale utente
Hitachi
Hitachi SPX-WKT3 Manuale utente
Hitachi
Hitachi RC-AGU1EA0A Manuale utente
Hitachi
Hitachi PC-ARFH1E-02 Manuale utente
Hitachi
Hitachi PC-ARFG-E Manuale utente
Hitachi
Hitachi RAR-6N1 Manuale utente
Hitachi
Hitachi RAR-M0A5 Manuale utente
Hitachi
Hitachi ECO COMPACT PC-ARC-E Manuale utente
Hitachi
Hitachi SPX-RCKA2 Manuale utente
