HiTi Digital P510L Manuale utente

Printer

Troubleshooting Guide

All Printers

It is paramount that the manufacturer instructions for transporting the

printer be followed. Both Hiti and Ciaat require that you remove all media -

paper and ribbon - from the printer before transporting. More than 60% of all

printer issues result from failure to remove the media prior to transporting. This

can cause physical damage to the media as well as the internal components of

the printer.

Also, check regularly for any debris and/or dust inside of the printer in between

events.

Basic Troubleshooting

With all printers running on a Windows PC there are several things that can be

done regardless of the make or model of the printer.

I. Check USB connection

A. Make sure that you are plugging the printer into the same USB port each

time you set up. Changing ports can confuse Windows.

B. Unplug the USB connection from the computer, wait five seconds, then

plug the USB back into the computer.

C. If printer is continuously not detected, try plugging into a different USB

port. If the printer is suddenly detected then there could be a hardware

problem with the previous US

D. Check USB cable connection on the printer to make sure it is not loose.

II. Reload Media

A. Sometimes it is necessary to completely remove media and reload it.

Do so slowly and carefully.

III. Check for debris in the printer

A. At times the cutter can cause debris to slip into the printer. Visually

inspect all paper paths available.

B. Use canned air to blow into areas you cannot see clearly. This will help

to dislodge any debris.

IV. Power off Printer

A. It can help to clear bad data out of the printer memory by turning the

printer (only the printer) off for a period of 30 seconds. After 30 seconds

turn the printer back on.

V. Replace USB Cable

A. Since the USB cable mostly sits there untouched it is not often thought

that the cable itself can just go bad. In essence the USB cable is just

another power cable that also transmits data. These cables can on

occasion go bad without warning. It is a good idea to have a spare USB

cable on hand.

VI. Darkroom Print Queue

A. Go into Darkroom, Prints.

B. Select print in the middle of the black menu bar.

C. Choose Show Print Queue.

1. If there are any jobs in the queue click on Delete All Print Jobs along

the left side. This will remove any corrupted print jobs that can hold

up the printing.

VII. Turn printer off then back on

A. The power switch for the Brava 21 is on the back near where the power

cord connects. Switch the power off and wait for 30 seconds, then

switch the power back on.!

Ciaat Brava 21 Troubleshooting

Torn Ribbon

The ribbon can be easily repaired with scotch tape. Just bring the two broken

ends together and tape both sides with scotch tape. Then roll the broken area

onto the uptake roll.

Checking for Debris

If no debris is seen in the cavity of the printer, there could possibly be debris in

the paper path. To check for this, remove the paper roll and look to see if any

debris is visible.

Next reload the paper, but when the Paper Load green light comes on,

continue pushing the paper until you see the edge appear in the ribbon

compartment. This will usually push any debris along the path into the open

area and clear the path.

Remove and Re-add Printer

The Brava 21 runs on a built-in driver in Darkroom. You can remove the printer

and add it back in with just a few clicks:

1. In Darkroom, go to Global Settings, Printer Options.

2. Click on the Brava 21 to highlight it.

3. Along the right side, click on Remove Printer.

4. To add it back, click on Add Printer along the right side.

5. Select the Brava 21 at the top of the list in the printer selection window.

The printer is now added back into Darkroom.

Error Codes

The complete printer manual for the Brava 21 is included in your printed Booth

manual. Below is the error light page. Generally most error situations have to

do with the media not being loaded correctly, or a small jam. Removing the

paper and ribbon will typically fix issues.

Adjusting the Ribbon

If reloading the ribbon does not work initially, remove the ribbon and roll 6

inches of it into the take-up roll, then reinsert. There is information on the

ribbon that the printer reads and this information can be faulty. Adjusting the

position of the ribbon material will force the printer to advance to the next

information strip.

Hiti P510L Troubleshooting

Ribbon rip or Paper Jam

Open the side door of your printer. Rewind the paper back into the

roll by turning the handle in the direction of the arrow. Push the

button and remove the paper.

Does the paper have a clean-cut edge?

If the edge of the paper iscrumpled, you will need some scissors to cut

a clean edge.

Is the ribbon torn?

You have two options:

1. If you can find some scotch tape nearby, you can simply tape

the two sides back together and then wind it up into the reel.

2. Feed one side of the ribbon onto the other and roll in into

thereel.

Printer Still Jamming?

It’s likely you have a small piece of paper, debris, or something in the

printer.

Don’t see anything in the printer? Check again! We’ve found some

super small pieces of paper trapped in there that have caused a jam. If

everything looks good, install everything back inside per usual

installation. Turn the printer off/on, and try another print.

If it says there is a printer jam, it really means there is a jam. There is

something somewhere blocking/interfering with the print. This may

require service, you will want to contact Hiti.

Disable Automatic Cutting for 4x6/postcard prints

This is a setting within Darkroom:

Open Darkroom and head to Global Settings (upper right-hand

corner)> Select Printer Options> Right-click the printer and select

Configure> Properties> select the Paper tab> select 6×4 (not 6×4

split) from the drop-down menu and make sure this setting is saved

before testing.

Removing the Printer from the Photo Booth

Two options here based on when your booth was constructed.

1. Most recent photo booths 11/13 – 11/14 (Hiti printers) -

Remove the screw that is found to the right of the printer.

Once removed, simply slide the printer out on the piece of

wood that it is attached to.

2. Unscrew the block of wood that is secured above the printer.

(Below your laptop or on the same board as your computer).

Once the block is removed, grab the printer, lift it upwards, and

pull it out. You need to lift about ¾of an inch to be able to

pull it out.

Printer is Offline

Check Devices and Printers to see if the printer is appearing here. You

can get to Devices and Printers on Windows 8 by pressing the

“windows” button and C at the same time and searching for “Devices”

and click on ‘Devices and Printers’. You can also swipe from the right of

the screen and then search for ‘devices and printers’. Windows 7,

Start Menu > Control Panel> Printers and Devices.

Right-click the HiTi P510L and make it the default printer. If there are

multiple copies (Copy 1, Copy 2, etc…), select the highest copy of

printer.

If it’s not appearing here, make sure the USB cable and power cords

are both securely plugged in at both ends. Try unplugging/plugging

both the USB and Power cables back in (if the printer was plugged into

the USB hub, try plugging directly into the computer this time to make

sure it’s receiving enough power).

Do you see the green light on the printer? (If you see an amber light,

this usually indicates an error)

If your printer isn’t on, check the power switch on the back of the

printer (may need to pull out first, unless you have long/skinny arms).

Still having issues, or have an error? Contact Imaging Spectrum or HiTi

for support.

Printer is Not Printing

1. Print Make sure printer isn’t offline (see “Printer Offline?” section)

and make sure you have a solid green light on the printer (anything

else usually indicates a paper jam, the printer door not properly

closed, out of paper, or the printer not turned on).

2. While in Devices and Printers, check to make sure printer is not

offline and is selected as the default, make sure that you have the

highest printer copy selected (if there are more than one copy of

the printer appearing).

3. While still under Devices and Printers, double-click on the printer

toview the printing queue and delete any jobs that are pending.

Then click “Printer” in the top left corner of the printer queue

window and make sure there isn’t a check mark next to “Pause

Printing”. If there is, deselect it.

4. To print a test page, Open Devices and Printers by clicking

the Start button !, and then, on the Start menu, clicking Devices

and Printers, Right-click a printer, and then click Printer properties.

On the General tab, click Print Test Page. If successful, continue to

step 5. If not successful, see “Reinstalling Printer Drivers” and then

repeat steps 1-4 here.

5. Open Darkroom and head to Global Settings (upper right-hand

corner)> Select Printer Options> if there is currently a printer

appearing here, right-click and remove this printer.

6. Select Add Printer (right-hand side)> select windows printer and

then press “Add Printer”> click on the Hiti P510L Printer and then

Altri manuali per P510L

Indice

Altri manuali HiTi Digital Stampante

HiTi Digital

HiTi Digital M610 Manuale utente

HiTi Digital

HiTi Digital P510L Manuale utente

HiTi Digital

HiTi Digital P910L Manuale utente

HiTi Digital

HiTi Digital P320W Manuale utente

HiTi Digital

HiTi Digital P528L Manuale utente

HiTi Digital

HiTi Digital S400 Manuale utente

HiTi Digital

HiTi Digital CS-200e Manuale utente

HiTi Digital

HiTi Digital P750L Manuale utente

HiTi Digital

HiTi Digital CS-310 Manuale utente

HiTi Digital

HiTi Digital 630PS Manuale utente

HiTi Digital

HiTi Digital P710L Manuale utente

HiTi Digital

HiTi Digital P510k Manuale utente

HiTi Digital

HiTi Digital CS-222e Manuale utente

HiTi Digital

HiTi Digital CS-200e Istruzioni per l'installazione

HiTi Digital

HiTi Digital P710L Manuale utente

HiTi Digital

HiTi Digital CS-300 Manuale utente

HiTi Digital

HiTi Digital Photo Printer 640PS Manuale utente

HiTi Digital

HiTi Digital S420 Manuale utente

HiTi Digital

HiTi Digital P520L Manuale utente

HiTi Digital

HiTi Digital P525L Manuale utente

HiTi Digital

HiTi Digital P3X Manuale utente

HiTi Digital

HiTi Digital Printhome Manuale utente

HiTi Digital

HiTi Digital P910L Manuale utente

HiTi Digital

HiTi Digital 640 DL Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente