HMS Networks Anybus Wireless Bolt LTE Guida utente

Anybus®Wireless Bolt LTE™

STARTUP GUIDE

SP2868

Version 1.2

Publicaon date 2022-05-16

ENGLISH

Important User Informaon

Disclaimer

The informaon in this document is for informaonal purposes only. Please inform

HMS Networks of any inaccuracies or omissions found in this document. HMS Networks

disclaims any responsibility or liability for any errors that may appear in this document.

HMS Networks reserves the right to modify its products in line with its policy of

connuous product development. The informaon in this document shall therefore not

be construed as a commitment on the part of HMS Networks and is subject to change

without noce. HMS Networks makes no commitment to update or keep current the

informaon in this document.

The data, examples and illustraons found in this document are included for illustrave

purposes and are only intended to help improve understanding of the funconality and

handling of the product. In view of the wide range of possible applicaons of the product,

and because of the many variables and requirements associated with any parcular

implementaon, HMS Networks cannot assume responsibility or liability for actual use

based on the data, examples or illustraons included in this document nor for any

damages incurred during installaon of the product. Those responsible for the use of

the product must acquire sucient knowledge in order to ensure that the product is

used correctly in their specic applicaon and that the applicaon meets all performance

and safety requirements including any applicable laws, regulaons, codes and standards.

Further, HMS Networks will under no circumstances assume liability or responsibility for

any problems that may arise as a result from the use of undocumented features or

funconal side eects found outside the documented scope of the product. The eects

caused by any direct or indirect use of such aspects of the product are undened and may

include e.g. compability issues and stability issues.

Contact Informaon

Postal address:

Box 4126

300 04 Halmstad, Sweden

E-Mail: inf[email protected]

1. Preface

1.1. About This Document

This document describes how to install Anybus® Wireless Bolt LTE™.

For addional documentaon and soware downloads, FAQs, troubleshoong guides and

technical support, please visit www.anybus.com/support.

1.2. Document Convenons

Safety Symbols

DANGER

Instrucons that must be followed to avoid an imminently hazardous

situaon which, if not avoided, will result in death or serious injury.

WARNING

Instrucons that must be followed to avoid a potenal hazardous situaon

that, if not avoided, could result in death or serious injury.

CAUTION

Instrucon that must be followed to avoid a potenal hazardous situaon

that, if not avoided, could result in minor or moderate injury.

IMPORTANT

Instrucon that must be followed to avoid a risk of reduced funconality

and/or damage to the equipment, or to avoid a network security risk.

Preface Anybus® Wireless Bolt LTE™

SP2868 Version 1.2 Page 1 of 28

Informaon Symbols

NOTE

Addional informaon which may facilitate installaon and/or operaon.

TIP

Helpful advice and suggesons.

1.3. Trademarks

Anybus® is a registered trademark and Wireless Bolt LTE™ is a trademark of HMS Networks

AB.

All other trademarks are the property of their respecve holders.

Anybus® Wireless Bolt LTE™Trademarks

Page 2 of 28 SP2868 Version 1.2

2. Safety

2.1. General Safety

CAUTION

This equipment emits RF energy in the ISM (Industrial, Scienc, Medical)

band. Make sure that all medical devices used in proximity to this

equipment meet appropriate suscepbility specicaons for this type of

RF energy.

CAUTION

This equipment contains parts that can be damaged by electrostac

discharge (ESD). Use ESD prevenon measures to avoid damage.

CAUTION

Minimum temperature rang of the cable to be connected to the eld

wiring terminals, 90 °C.

CAUTION

Use copper wire only for eld wiring terminals.

CAUTION

This equipment is recommended for use in both industrial and domesc

environments. For industrial environments it is mandatory to use the

funconal earth connecon to comply with immunity requirements. For

domesc environments the funconal earth must be used if a shielded

Ethernet cable is used, in order to meet emission requirements.

Safety Anybus® Wireless Bolt LTE™

SP2868 Version 1.2 Page 3 of 28

2.2. Intended Use

The intended use of this equipment is as a communicaon interface and router.

The equipment receives and transmits data over Ethernet and Cellular standard networks.

Anybus® Wireless Bolt LTE™Intended Use

Page 4 of 28 SP2868 Version 1.2

3. Preparaon

3.1. Support and Resources

For addional documentaon and soware downloads, FAQs, troubleshoong guides and

technical support, please visit www.anybus.com/support.

TIP

Have the product arcle number available, to search for the product

specic support web page. You nd the product arcle number on the

product cover.

3.2. Network Environment

Ensure that you have all the necessary informaon about the capabilies and restricons

of your local network environment before installaon.

3.3. Placement

Antenna Consideraons

The characteriscs of the internal antenna should be considered when choosing the

placement and orientaon of the unit.

Required Distance Between Devices

For opmal recepon, cellular devices should not be conned in buildings made of

concrete or metal, without windows.

To avoid interference, a minimum distance of 50 cm between cellular devices should be

observed.

At least 20 cm separaon distance between the device and the user’s body must be

maintained at all mes.

Preparaon Anybus® Wireless Bolt LTE™

SP2868 Version 1.2 Page 5 of 28

3.4. SIM Card

Prepaid Data Plan

If a prepaid data plan is used, ensure that:

• the data amount is sucient

• that any SMS nocaons are sent to a monitored number

3.5. Network Operator Cered Firmware

You may need to install a rmware cered for the operator you are going to use, it is not

possible to connect the Bolt LTE to the operator network otherwise.

Before you start to congure the Bolt LTE sengs:

• Ensure that the current rmware installed on the Bolt LTE is valid for the network

operator you are going to use.

• You nd the rmware version number in the Bolt LTE built-in web interface Overview

page. See Bolt LTE Built-In Web Interface (page 19).

• If you need to install a rmware version cered for your network operator:

Download the rmware update le, specic for your network operator, from

www.anybus.com/support.

• For informaon on how to update the rmware, see the Bolt LTE User Manual.

3.6. Firewall and Roung

There are roung opons set for the system.

By default, the rewall allow roung of:

• Outgoing trac for TCP, UDP and ICMP (for IPv4 only).

• Incoming trac for already established connecons only.

For other possible conguraons, see the Bolt LTE User Manual.

Anybus® Wireless Bolt LTE™SIM Card

Page 6 of 28 SP2868 Version 1.2

4. Installaon

4.1. Install SIM Card

NOTE

Supported SIM card types are Nano SIM for IoT and M2M, for data

communicaon, as well as standard mobile phone Nano SIM.

Figure 1. Insert SIM card

To connect Bolt LTE to a cellular data network, install a cellular SIM card:

1. Insert a SIM card into the Bolt LTE SIM card holder.

NOTE

Ensure that the SIM card contact surface is facing towards the

Ethernet port.

Installaon Anybus® Wireless Bolt LTE™

SP2868 Version 1.2 Page 7 of 28

4.2. Mechanical Installaon

Placement

• The device is intended to be mounted on top of a machine or cabinet through an M50

(50.5mm) hole using the included sealing ring and nut.

• The top mounng surface, in contact with the sealing, must be at with a nish

equivalent to Ra 3.2 or ner and cleaned and free from oils and greases.

• For opmal recepon, cellular devices require a zone around them clear of objects that

could obstruct or reect the signal.

To avoid interference, a minimum distance of 50 cm between Bolt LTE and other cellular

devices should be observed.

Installaon

IMPORTANT

Make sure that the sealing ring is correctly placed in the circular groove in

the top part of the housing before ghtening the nut.

IMPORTANT

Always hold the BOTTOM part of the unit when unghtening the nut, not

the top part (the cap).

Tightening torque: 5 Nm ±10 %

Anybus® Wireless Bolt LTE™Mechanical Installaon

Page 8 of 28 SP2868 Version 1.2

Altri manuali per Anybus Wireless Bolt LTE

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HMS Networks Hardware di rete

HMS Networks

HMS Networks Ixxat CANbridge NT 200 Manuale utente

HMS Networks

HMS Networks Airconwithme Guida all'applicazione

HMS Networks

HMS Networks Anybus Wireless Bolt II Manuale utente

HMS Networks

HMS Networks Anybus WirelessBolt RJ45 PoE Series Guida utente

HMS Networks

HMS Networks Ixxat CANnector Series Manuale utente

HMS Networks

HMS Networks Anybus Terminator T1 Manuale utente

HMS Networks

HMS Networks Anybus Communicator Manuale utente

HMS Networks

HMS Networks Anybus Communicator ABC3028 Manuale utente

HMS Networks

HMS Networks Anybus CompactCom 40 POWERLINK Istruzioni di installazione e manutenzione

HMS Networks

HMS Networks Anybus CompactCom 40 POWERLINK Istruzioni di installazione e manutenzione

HMS Networks

HMS Networks Anybus Wireless Bolt LTE Guida utente

HMS Networks

HMS Networks Anybus CompactCom 40 POWERLINK Istruzioni per l'installazione e il funzionamento

HMS Networks

HMS Networks Anybus Wireless Bridge II CAN Manuale utente

HMS Networks

HMS Networks Ewon FLB 3208 Manuale utente

HMS Networks

HMS Networks Anybus Wireless Bolt LTE Manuale utente

HMS Networks

HMS Networks Anybux Wireless Bolt Serial Guida utente

HMS Networks

HMS Networks Intesis INBACRTR03200 Series Manuale utente

HMS Networks

HMS Networks Ixxat CAN-Gateway Configurator V6 Manuale utente

HMS Networks

HMS Networks Anybus Communicator ABC4021 Manuale utente

HMS Networks

HMS Networks Ewon Cosy+ Manuale utente

HMS Networks

HMS Networks Ewon Cosy 131 Manuale utente

HMS Networks

HMS Networks Ewon Cosy + Manuale utente

HMS Networks

HMS Networks Anybus Communicator ABC4023 Manuale utente

HMS Networks

HMS Networks Intesis KNX Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente