Hobby King HUMMER EPP-3D Manuale utente
Before use, please read the explanations carefully!
HUMMER EPP- 3D
Instruction Manual
Specifications
•Fuselage: Length 950mm
•Wingspan: 1000mm
•Flying Weight: 450 - 500g (with battery)
•Additi nal Required Equipment (n t included in the kit
•M t r: 2212 1000KV r2213 1000KV
•ESC: 20A
•Pr peller: 1047 Sl w Flyer Pr p
•Serv : 4 * 9G
•Radi ::4/m re channels 4
•Battery: 11.1V 850-1300mAh li-p
SAFETY PRE AUTIONS
1. We rec mmend that y u get the assistance f an experienced pil t during the
assembling
pr cess.
2. The kit c ntains small parts. S keep ut f children's reach when assembling.
3. The flying weight f the plane is ab ut 400g. In rder t ensure the flight perf rmance,
use the m t r and battery with suitable weight.
P a r t s L i s t :
•Main wing (pair):1
•Fuselage: 1
•Stiffened f Fuselage (pair): 2
•Tail plane :1
•Rudder : 1
•Plyw d M t r M unt ( set): 1
•Z-shaped steel wire : 8
•Airplane wheel and plastic wheel ch ck : 2
•Landing gear steel wire : 1
•W d supp rt plate f landing gear 1
•Serv h rn : 4
•Heat shrink tube : 1
•990 mm Carb n r d: 2
•780mm Carb n r d: 3
•330mm elevat r 330 mm w d strip: 2
•hinge : 4
Construction:
1. Stick the 2 pieces f main wings symmetrical with 502 glue.
2. Put 2 pieces f carb n r ds with 990mm length and 2mm diameter int the sl t f
aircraft wing's t p and b tt m surface.
3. Stick the tw carb n r ds in the t p and b tt m t the aircraft wing with 502 glue t
enf rce the aircraft wing's strength.
4. Put 2 pieces f carb n r ds with the length f 780mm int the sl t f fuselage's stiffener,
pay attenti n t the right and left directi n.
5. Stick the stiffener t the b dy f aircraft with f am glue, the fuselage sh uld keep
straight.
6.. C nnect carb n r d with stiffener with 502 glue after the stiffener has been adherent t
the fuselage firmly.
7. Check fuselage t make sure it is straight bef re the glue s lidifies t tally.
8. Insert the aircraft wing int b dy f aircraft ( as illustrated in the picture ) .
9. Bef re sticking the t p surface t the b dy f aircraft please check the right and left
p siti n f the aircraft wing t see whether they are symmetrical.
10. Stick w d strips f landing gear with 502 glue, please make sure the sl t f r landing
gear sh uld be kept upward.
11. Stick the w d access ries f the landing gear t the fuselage with 502 glue.
12. Dr p the 502 glue int the juncti n f l wer surface f aircraft wing and the b dy f
aircraft.
13. Put 2 pieces f l ng w d strip int the 330*4 sl t.
14. Stick it with 502 glue.
15. Put the h riz ntal tail int the fuselage and stick them t make sure they are
symmetrical.
16. Assemble the main aircraft wing and h riz ntal tail c rrectly, and make sure A=B as
well C=D.
17. Stick ne plastic serv h rn t the vertical tail with 502 glue and make sure the
distance between serv h rn and the l wer part f the vertical tail sh uld be 92mm.
18. Cut a sl t in the edge f vertical tail with craft knife, insert half-size f the 4 pieces f
paper hinge int the stick, then stick them with 502 glue.
19. Cut a sl t in the fuselage after insert the paper hinge, stick them with 502 glue.
20. Stick the plastic serv h rn t the p siti n illustrated in the picture.
21. Cut a serv h le in the fuselage and make sure the serv h le is at a distance f 13cm
fr m tail angle.
22. C nnect serv c nnecting r d carb n r d t steel wire with h t shrink tube.
23. Make sure the angel between c nnecting r d and serv arm sh uld be vertical. After
adjust the length f c nnecting r d, dr p 502 glue int the seam f h t shrink tube t stick.
24. Stick the w d strips f m t r m unt with 502 glue.
25. Inset the head f fuselage then stick it with 502 glue. 26. Put landing gear steel wire
int the h t shrink tube after it fixed with wheel, then stick the tube with 502 glue.
27. Insert the landing gear int the fuselage, then insert the w d stave int the se<am
then stick with 502 glue.
28. Fix the m t r t Plyw d M t r M unt with self-Tapping Screws.
29. Refer t the p siti n f receiver
30. The centre f gravity sh uld be 120-130mm fr m the fr nt edge f aircraft wing.
31. We suggest that y u add 1- 2 degrees f right-thrust, which can be achieved by adding
ne washer r tw behind the t p and right side f the m t r (between the m t r and the
m t r m unt). When set pr perly, the trim f r the elevat r and the rudder sh uld be
neutral. Fine-tune the d wn-thrust and right-thrust until this trim is achieved. When d ing
flight test, we suggest y u sh uld keep the flight balance acc rding t the centre f gravity
we rec mmend. When d ing 3D flight test, y u can m ve slightly the centre f gravity
backward.
General flight: Ailer n: 20 degrees, Elevat r: 20 degrees, Rudder: 20 degrees.
3D flight: Ailer n : 45-55 degrees, Elevat r: 45-60 degrees, Rudder: 45-60 degrees.
Seek Assistance: If y u are a beginner in the R/C field, we suggest y u turn t an
experienced pil t f r help with the first few flights.
E-Mail: inf @wxhymx.c m [email protected] m
RED EAGLE M DEL www.wxhymx.c m Made in China
Indice
Altri manuali Hobby King Giocattolo
Hobby King
Hobby King EXTRA260P Manuale utente
Hobby King
Hobby King RYAN-STA Manuale utente
Hobby King
Hobby King Angel 920 Manuale utente
Hobby King
Hobby King Aether 3700 EP Manuale utente
Hobby King
Hobby King Skipper 40228 Manuale utente
Hobby King
Hobby King H-KING Cri Cri Manuale utente
Hobby King
Hobby King HD Wing Camera Manuale utente
Hobby King
Hobby King Airoso F3A Manuale utente
Hobby King
Hobby King SU-35 FIGHTER Manuale utente
Hobby King
Hobby King Delta Rocket 100 Manuale utente
Hobby King
Hobby King J3 NAVY CUB Manuale utente
Hobby King
Hobby King Mellizo-50e Manuale utente
Hobby King
Hobby King Mariposa Trainer Manuale utente
Hobby King
Hobby King FALCON TRAINER Manuale utente
Hobby King
Hobby King YAK- EPP Manuale utente
Hobby King
Hobby King Katana EPP-30E Manuale utente
Hobby King
Hobby King PT-17 Manuale utente
Hobby King
Hobby King Raven 990 MINI DLG 2017 Manuale utente
Hobby King
Hobby King B-17G Manuale utente
Hobby King
Hobby King DH 82 Tiger Moth Manuale utente
