HoldPeak HP-760E Manuale utente
760E
OPERATION
MANUAL
1
1. ATIONSAFETY INFORM SAFETY SYMBOLS
Warning! Dangerous Voltage (Risk of electric shock).
Caution! Refer to the user’s manual before using this Meter.
Double Insulation (Protection Class Ⅲ).
Alternating Current (AC).
Direct Current (DC).
Either DC or AC.
Ground (maximum permitted voltage between terminal and
ground).
The symbol indicating separate collection for electrical and
electronic equipment.
The RESPONSIBLE BODY shall be made aware that, if the
instrument is used in a manner not specified by the
manufacturer, the protection provided by the instrument may
be impaired.
The finger or any part of your body shall not be beyond
the barrier of the test probe when measuring.
Individual protective equipment must be used if
HAZARDOUS LIVE parts in the installation where
measurement is to be carried out could be ACCESSIBLE.
The following safety information must be observed to insure
maximum personal safety during the operation at this meter.
Do not operate the meter if the body of meter or the test lead
look broken.
Check the main function dial and make sure it is at the correct
position before each measurement.
When making current measurements ensure that the circuit not
“live” before opening it in order to connect the test leads.
Do not perform resistance, capacitance, temperature, diode
2
and continuity test on a live power system.
Do not apply voltage between the test terminals and test terminal
to ground that exceed the maximum limit record in this manual.
Exercise extreme caution when measuring live system with
voltage greater than 60V DC or 30V AC.
Change the battery when the “ ” symbol appears to avoid
incorrect data.
Use the DMM indoor, altitude up to 2000m and temperature 5°C
to 40°C.
Maximum relative humidity 80% for temperatures up to 31°C,
decreasing linearly to 50% relative humidity at 40°C.
1.9 In locations subject to radio frequency interference, the
product may malfunction and it resets automatically when leaving
this environment.
Meter Description
■Terminals
Refer to table 1 for terminal function
Terminal
Function
COM
Common terminal for all measurement
V/Ω/HzT
Volts , Ohm , Diode , Freq. , Temp. and Cap. Measurement and
square wave output terminal
Clamp
μAmA
Clamp，Microampere, milliampere current measurement terminal
20A
Ampere current measurement terminal
Table 1. Terminals
3
Figure1.terminal
■Rotary switch
Position of
Rotary switch
Function
20A
DC&AC Ampere current
mA
DC&AC milliampere current
μA
DC&AC microampere current
600A
DC&AC Ampere current
hFE
Transistor hFE test
Hz
Duty cycle / Frequency
mV
DC&AC millivolts
V
DC&AC voltage
Capacitance
Ω
Resistance, Diode & continuity
℃/℉
Temperature
OFF
Power off
Table 2. Rotary switch functions
4
Figure2. Rotary switch
■Push button
Figure3. Push button
1.SELECT
●Press this button to select your measurement mode.
2.RANGE
5
● When the meter is powered on, the meter is in the auto range mode;
press this button to select a specific measurement range.
● Press this push button more than 2 seconds the meter returns to auto
range.
3.MAX/MIN
● Pressing this button the meter enters the dynamic record mode.
● In the dynamic record mode, pressing this button again cycles MAX,
MIN , AVG , MAX-MIN and Present Reading on.
4. HOLD
● Pressing this button, the meter enters the auto data hold mode and
“H” is displayed on the LCD.
● The data hold function allows the operator to hold a displayed value
on the LCD while the analog bar graph continues to display the updated
value.
● In the auto hold mode the meter can display a new value when a new
and stable value is on the input and the Beeper will sound.
● Pressing this button for more than 1 seconds, the meter exits the
HOLD mode and returns to the normal state.
● Pressing the button for more than 2 seconds turns the backlight
on,look the Selector Knob more clearly, pressing it again turns it off..
5
.REL△
● Pressing this button, the meter enters relative measuring mode,
“REL▲”is displayed on the LCD and the present reading becomes the
6
reference value and displayed on the secondary display. Relative
measurement has two modes. REL▲=measurement value-Reference
value, the other is REL%=(REL▲/Reference value)×100% (press
SELECT
to select REL△or REL% mode)..
● Set up reference value for your measurement.
select your measurement function and your
RANGE
.
Press
SET
once, then press
SELECT
twice to select the reference
value for a measurement.
● Pressing the
REL△
button for more than 2 seconds returns the
meter to normal state.
Pressing the button turns the backlight on, look the Selector Knob more
clearly, pressing it again turns it off.
6.
Hz/Duty
pressing the button display the Duty Cycle, pressing it again display
Frepuency.
2. SPECIFICATIONS
2.1 GENERAL SPECIFICATIONS
Display: LCD with a max. reading of 6000 & Analogue bar
graph.
Range control: Auto range & Manual range control.
Polarity: Automatic negative polarity indication.
Zero adjustment: Automatic.
Over range indication: The “OL” or “-OL” display.
7
Low battery indication: Display " " sign.
Data hold: Display “HOLD” sign.
Relative measurement: Display “△” sign.
Auto Power Off: Display “APO” sign. When measurement
exceeds 15 minutes without switching mode and pressing key, the
meter will switch to standby mode. Press any key or switch
selector switch to exit standby mode. When restart the system,
press and hold SELECT key to disable auto power off.
Mechanical blocking system for terminal sockets to prevent
mistake operation.
Bar graph display
Safety standards: EMC/LVD. CAT Ⅲ 1000V.
The meter is up to the standards of IEC1010 Double Insulation，
Pollution Degree 2, Overvoltage Category Ⅲ.
Operating environment:
Temperature 32 to104°F (0°C to 40°C),
Humidity ≤ 80% RH.
Storage environment:
Temperature -4 to140°F (-20°C to 60°C),
Humidity ≤ 90% RH.
Power supply: 9V battery
Dimension: 190mm×88.5mm×27.5mm
Weight: Approx.320g (including battery).
8
Express function：
New style patent of function direction light, easy use in dark place.
9
2.2 ELECTRICAL SPECIFICATIONS
Accuracies are ± (% of reading + number in last digit )at 23 ± 5°C ,
≤75% RH.
2.2.1 DC Voltage
Range
Accuracy
Resolution
60mV
± ( 0.8% of rdg+10digits )
0.01mV
600mV
± ( 0.5% of rdg+15 digits)
0.1mV
6V
1mV
60V
10mV
600V
100mV
1000V
± ( 0.8% of rdg+10 digits)
1V
Overload protection: 1000V DC or 750V AC rms
Impedance: ≥10MΩ
2.2.2 AC Voltage
Range
Accuracy
Resolution
60mV
± ( 2.0% of rdg+10 digits )
0.01mV
600mV
0.1mV
6V
± ( 1.5% of rdg+10 digits)
1mV
60V
10mV
600V
100mV
750V
± ( 2.0% of rdg+10 digits )
1V
Average sensing, calibrated to rms of sine wave
Frequency: 40～400Hz
Overload protection: 1000V DC or 750V AC rms
Impedance: ≥10MΩ
Indice
Altri manuali HoldPeak Multimetro
HoldPeak
HoldPeak 770G Manuale utente
HoldPeak
HoldPeak HP-36C Manuale utente
HoldPeak
HoldPeak 870E Manuale di installazione
HoldPeak
HoldPeak 6300 Manuale utente
HoldPeak
HoldPeak 6688D Manuale utente
HoldPeak
HoldPeak 90F Manuale utente
HoldPeak
HoldPeak 870N Manuale utente
HoldPeak
HoldPeak HP-37A Manuale utente
HoldPeak
HoldPeak 39B Manuale utente
HoldPeak
HoldPeak 39B Manuale utente
HoldPeak
HoldPeak 770A Manuale utente
HoldPeak
HoldPeak 870N Manuale utente
HoldPeak
HoldPeak 860D Manuale utente
HoldPeak
HoldPeak 770HD Manuale utente
HoldPeak
HoldPeak HP-770H Manuale utente
HoldPeak
HoldPeak HP-90E Manuale utente
HoldPeak
HoldPeak 760J Manuale di installazione
HoldPeak
HoldPeak HP-570C-APP Manuale utente
HoldPeak
HoldPeak HP-770H Manuale utente
HoldPeak
HoldPeak HP-37B Manuale utente
Manuali Multimetro popolari di altre marche
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuale utente
PeakTech
PeakTech 4000 Manuale per l'uso e la cura
YOKOGAWA
YOKOGAWA 90050B Manuale utente
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuale utente
Fluke
Fluke 8846A Manuale operativo e di manutenzione
Tempo Communications
Tempo Communications MM200 Manuale utente
