Hollyland Solidcom C1 Pro Manuale utente
Hollyland Solidcom C1 Pro Hub
User Manual
V1.0.0
Inteaces
1 2
NP-F Batte Slot
USB Inteace
Volume Knob
Display
0B10 Headset Inteace
B Button
OFF: The wired headset user is not in group B. In this case, the user cannot hear or talk with the
other headset users in group B.
ON in orange: The wired headset user is in group B. In this case, the user can hear and talk with
the other headset users in group B.
A Button
ANNOUNCE Button
Press and hold the button to mute all remote headsets in the system. In this case, the indicator
turns ON in orange.
PGM Audio Input Inteace
DC Power Inteace
Power Switch
2-Wire Audio Input & Output Inteace
UAC Inteace
RJ45 Inteace
V-Mount/G-Mount
Batte Plate
4-Wire Audio Input &
Output Inteace
(RJ45 Socket)
RF Antenna Inteace
OFF: The wired headset user is not in group A. In this case, the user cannot hear or talk
with the other headset users in group A.
ON in orange: The wired headset user is in group A. In this case, the user can hear and talk
with the other headset users in group A.
UP Arrow Button
DOWN Arrow Button
LEFT Arrow Button
RIGHT Arrow Button
Menu/Conrmation Button
Press and hold the button to enter
the menu inteace/Press the button
for conrmation.
3 4
Standard Line Sequence
0B10 Wired Headset Inteace 2-Wire Audio Input & Output Inteace
PGM Audio Input Inteace
RJ451/RJ452 Inteace
PIN1: SPK+
PIN2: SPK-
PIN3: ENC
PIN4: RGB-B
PIN8: MIC1 N-
PIN7: MIC1 P+
PIN6: MUTE
PIN5: RGB-A
PIN9: MIC2+
PIN10: GND
4-Wire Audio Input & Output Inteace
PIN1–PIN8
PIN1 GND
PIN2 GND
PIN3 AUDIO IN+
PIN4 AUDIO OUT+
PIN5 AUDIO OUT-
PIN6 AUDIO IN-
PIN7 GND
PIN8 GND
Standard Line Sequence
PIN1 Transceive Data+
PIN2 Transceive Data-
PIN3 Receive Data+
PIN4 Not connected
PIN5 Not connected
PIN6 Receive Data-
PIN7 Not connected
PIN8 Not connected
PIN1 GND
PIN2 GND
PIN3 AUDIO OUT+
PIN4 AUDIO IN+
PIN5 AUDIO IN-
PIN6 AUDIO OUT-
PIN7 GND
PIN8 GND
Cross Line Sequence
PIN1: GND
PIN3: AUDIO
PIN2: POWER
PIN1: GND
PIN3: AUDIO IN+
PIN2: AUDIO IN-
PIN1–PIN8
Hub Display Description
Master
① Hub Mode (Master/Remote)
② Hub Batte Level
③ Wired Headset Signal Strength
④ Wired Headset Batte Level (Red: Low Batte)
⑤ Wired Headset Number
⑥ Wired Headset Status
TALK: The wired headset user can hear and talk with the other headset
users.
MUTE: The wired headset user is muted and can only hear the other head-
set users.
LOST: The wired headset is disconnected from the hub.
LINK: The wired headset is reconnecting to the hub.
⑦ Network Connection Status
⑧ Wi-Fi Status
5
Operation Guide
6
Hub Menu Description
Press and hold the Menu/Conrmation button for about 3 seconds to enter
the menu inteace.
1. Select Network to enter the network conguration inteace.
1.1 Select Wi Setting to turn Wi-Fi ON or OFF. After it is turned ON, the IP
address, SSID, and password are displayed.
Operation Guide
Menu
Network M & R
Info
Language2 Wire4 Wire
PGMGroup
PGM
IP Address: 192.168. 217.100
SSID: HLD_12345678
Password: 12345678
WIFI Setting
ON
OFF
1.2 Select Wired Network Setting to turn DHCP ON or OFF. If it is turned OFF, you
can also modify the IP address, subnet mask, and gateway as well as view the
user name and password for logging in to the web.
2. Select M & R to set the hub as the master device or remote device.
2.1 Select Master Device to set the hub as the master device.
Operation Guide
admin
12345678
User Name:
Password:
192.168.218.10
IP Address:
255.255.255.0
Subnet Mask:
192.168.218.1
Modify
Wired Network Setting
ON
OFF
Gateway:
Modify
Modify
Master And Remote
Remote Device
Master Device
7
2.2 Select Remote Device and then select Scan to scan the IP addresses of master
devices on the network. Select the IP address of the corresponding master
device in the displayed list and conrm it. Then, the hub is successfully set as the
remote device.
• When a single hub is used, the hub needs to be set as the master device.
• When more than two hubs are used in a cascaded connection, one hub
needs to be set as the master device and the other hubs as the remote
devices.
3. Select Group to peorm group settings and view group status.
3.1 There are three options: A group (All devices are in group A), AB group (All
devices are in groups A and B), and Customize (The group settings can be
customized on the web. All devices are in group A by default).
Operation Guide
Master 1 IP: 192.168.218.011
Master 3 IP: 192.168.218.013
Master 4 IP: 192.168.218.014
Master 5 IP: 192.168.218.015
Master 2 IP: 192.168.218.012
Master-Remote Device
Group Presets
A group
AB group
Customize
8
3.2 Select Group Review to view group settings.
4. Select PGM to set the PGM audio gain according to the input volume.
5. Select 4 Wire to peorm 4-wire audio settings.
5.1 Select Input Gain to set the input gain according to the input volume.
Operation Guide
1
8765
432
-12dB
-6dB
0dB
6dB
Gain Setting
-18dB
-18dB
-12dB
-6dB
0dB
6dB
Input Gain
9
5.2 Select Output Gain to set the output gain according to the input volume.
5.3 Select Line Sequence Switching to switch between Standard and Cross modes.
Operation Guide
Cross
3 4
OUT+ IN+
5 6
IN- OUT-
3 4
IN+ OUT+
5 6
OUT- IN-
Line sequence switching
Standard
-18dB
-12dB
-6dB
0dB
6dB
Output Gain
10
6. Select 2 Wire to peorm 2-wire audio settings.
6.1 Connect the hub to a 2-wire device and set the corresponding cable compen-
sation and terminal resistance on the hub. Power on the 2-wire device and turn
OFF or disconnect its microphone to make sure that there is no other audio
transmission on the 2-wire link. Otherwise, the accuracy of auto-null settings
may be aected. After Auto Null is selected, auto-null settings for the 2-wire
device will be peormed automatically on the hub.
6.2 Select Cable Compen to check the 2-wire cable length and select the corre-
sponding compensation option according to the cable length.
6.3 Select Terminal Res to check whether the 2-wire device connected via the 2-wire
inteace has terminal resistance. If it has, select OFF. Otherwise, select ON.
Operation Guide
50m
100m
150m
200m
Cable Compen
ON
OFF
Terminal Res
11
Altri manuali per Solidcom C1 Pro
5
Indice
