Holtek E-Link Manuale utente

Holtek Flash MCU Quick Start Guide

Revision: V1.00 Date: August 04, 2017August 04, 2017

Holtek Flash MCU Quick Start Guide

Rev. 0.00 2 August 04, 2017

Table of Contents

1. Tool Introduction.............................................................................................. 3

2. Tool Description............................................................................................... 4

2.1 Software .................................................................................................................................4

2.2 Hardware................................................................................................................................5

Rev. 1.00 3 August 04, 2017

1. Tool Introduction

Holtek Flash MCU Quick Start Guide

Rev. 1.00 4 August 04, 2017 Rev. 1.00 5 August 04, 2017

Holtek Flash MCU Quick Start Guide

2. Tool Description

2.1 Software

HT-IDE3000

The HT-IDE3000 is a simulation software specially developed for HOLTEK 8-bit MCUs. When

used together with OCDS EV chip, it will implement a series of operations such as single step,

full speed, breakpoint setting, RAM monitor, etc. Refer to the HT-IDE3000 User’s Guide for more

information.

http://www.holtek.com.tw/documents/10179/106680/HT-IDE3000UsersGuide%281252%29.pdf?0113

HOPE3000

The HOPE3000 is a programming software specially designed for HOLTEK 8-bit MCUs. The

software includes erase, blank check, program, verify, etc. Refer to the e-Writer Series Writer User’s

Guide for more information.

http://www.holtek.com.tw/documents/10179/106680/e-Writer+Series+Writer+User%27s+Guide+%28English%29.pdf

HOPE3000 For e-Link

The HOPE3000 For e-Link is a programming software specially designed for HOLTEK 8-bit

MCUs. The software includes erase, blank check, program, verify, etc. Refer to the Holtek e-Link

ICP User’s Guide for more information.

http://www.holtek.com.tw/documents/10179/106680/e-Link+ICP+User%27s+Guide_ENv100--20150513.pdf

Rev. 1.00 4 August 04, 2017 Rev. 1.00 5 August 04, 2017

Holtek Flash MCU Quick Start Guide

2.2 Hardware

e-Link OCDS Emulation

The e-Link with HT-IDE3000 software can implement OCDS emulations. Only 4 pins are needed

to connect with the EV chip (IC with OCDS interface), which are VDD, GND, OCDSCK and

OCDSDA. The pin assignement is shown in the gure 1. If the AVDD and AVSS pins are existed

in the MCU, the AVDD pin must be connected together with VDD or other power supply, and the

AVSS pin must be connected together with VSS.

Fig.1 e-Link OCDS PIN

Fig.2 e-Link OCDS Emulation

Rev. 1.00 6 August 04, 2017 Rev. 1.00 7 August 04, 2017

Holtek Flash MCU Quick Start Guide

e-Link ICP Programming

The e-Link together with the HOPE3000 for e-Link software can implement programming MCUs,

which is suitable for engineering samples programming. Only 4 pins are needed to connect with the

MCU, which are VDD, GND, ICPCK and ICPDA. The pin assignement is shown in the gure 3. If

the AVDD and AVSS pins are existed in the MCU, the AVDD pin must be connected together with

VDD or other power supply, and the AVSS pin must be connected together with VSS.

Fig.3 e-Link ICP PIN

Fig.4 e-Link ICP Programming Connection

Rev. 1.00 6 August 04, 2017 Rev. 1.00 7 August 04, 2017

Holtek Flash MCU Quick Start Guide

e-WriterPro Progarmming

The e-WriterPro together with the HOPE3000 software can support On-Line Programming, Off-

Line Programming and other kinds of programming methods, which is suitable for engineering

sample programming and mass productions. Select proper download mode according to the actual

MCU package type and programming environment requirements, as shown in the following gure.

Fig.5 64-LQFP Programming Method (Using an e-Socket)

Rev. 1.00 8 August 04, 2017 Rev. 1.00 9 August 04, 2017

Holtek Flash MCU Quick Start Guide

Fig.6 ICP (e-CON12C) Programming Connection

Rev. 1.00 8 August 04, 2017 Rev. 1.00 9 August 04, 2017

Holtek Flash MCU Quick Start Guide

The information appearing in this Data Sheet is believed to be accurate at the time

of publication. However, Holtek assumes no responsibility arising from the use of

the specications described. The applications mentioned herein are used solely

for the purpose of illustration and Holtek makes no warranty or representation that

such applications will be suitable without further modification, nor recommends

the use of its products for application that may present a risk to human life due to

malfunction or otherwise. Holtek's products are not authorized for use as critical

components in life support devices or systems. Holtek reserves the right to alter

its products without prior notication. For the most up-to-date information, please

visit our web site at http://www.holtek.com/en/.

Altri manuali per e-Link

Altri manuali Holtek Ricevitore

Holtek

Holtek BC2401 Manuale di istruzioni

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente

Holtek e-Link Manuale utente

Manuali Ricevitore popolari di altre marche