Honeywell Notifier ID50 Foglio di istruzioni

ID50/60installation,

commissioning &

configuration

manual

997-263-000-11, Issue 11 January 2010

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

i 997-263-000-11, Issue 11

January 2010

Contents

1 Introduction 1

1.1 Manual Purpose 1

1.2 System Design and Planning 1

1.3 General 2

1.3.1 Date-dependent Functions 2

1.4 CE Marking 2

1.5 EN54 Functions 3

1.6 Ancillary Functions 4

1.7 Related Documents 5

1.8 Warnings and Cautions 5

1.9 Tips 5

1.10 Glossary of Icons 6

2 Installation Guide 7

2.1 How to Use this Section 7

2.2 Pre-Installation Check List 7

2.1.1 Some Panel DO’s and DON’T’s 7

2.3 Transient Protection 8

2.4 Product Inspection 9

2.4.1 Checking Your Panel for Damage 9

2.4.2 What to do if Panel is Damaged

or Suspect 10

2.5 Dismantling the Panel 11

2.5.1 Removing the Cover 11

2.5.2 Removing the Panel Electronics 12

2.5.3 Back Box Fixing 13

2.5.4 Semi-Flush Mounting Bezel (Optional) 14

2.6 Assembling the Panel 15

2.7 RS485 Communications Link 16

2.7.1 Fitting the RS485 Interface Module PCB17

2.8 RS232 Interface Connections 18

3 Cabling 19

3.1 Cabling Instructions 19

3.1.1 Cable Terminations 20

3.2 Cabling Installation Notes 21

3.2.1 Introduction 21

3.2.2 Quality of Cable and of Cable Installation 21

3.3 EMC Considerations 22

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

ii997-263-000-11, Issue 11

January 2010

3.3.1 Screen Termination 22

3.3.2 Ferrite Sleeves (Optional) 22

3.4 MICC Cables 22

4 Commissioning 23

4.1 Introduction 23

4.2 Preliminary Checks 23

4.3 Internal Checks 24

4.3.1 Jumper Link Options 24

4.4 External Wiring Checks 25

4.4.1 Loop Wiring 26

4.4.2 RS485 Communications Link 27

4.4.3 DC Auxiliary Output 27

4.4.4 Sounder Circuit Outputs 28

4.4.5 CFG Outputs C and D 30

4.4.6 -VE Outputs 31

4.4.7 Digital / ÜE Inputs 31

4.4.8 Switch Connections 31

4.5 Powering the Panel 32

4.5.1 Start-up Language Selection 32

4.5.2 Batteries 33

4.6 Configuration and Handover 34

4.7 Commissioning Tests 35

4.7.1 Test LEDs 35

4.7.2 Test LCD 35

4.7.3 Test Zones 35

4.7.4 Test Auto High Test 35

4.7.5 Test Outputs 35

4.7.6 Test Buzzer 35

4.7.7 Test Keyboard 35

4.8 Sensors and Modules 36

4.8.1 EN54 Requirements 36

4.8.2 Loop Wiring Testing 36

5 Configuration 37

5.1 Introduction 37

5.2 Navigation and Number Entry 37

5.3 Level 2 Configuration Options 37

5.4 Level 3 Configuration Options 38

5.5 Setup Options 39

5.5.1 Panel Options 39

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

iii 997-263-000-11, Issue 11

January 2010

5.5.2 Site Details 45

5.5.3 Device Options 46

5.5.4 Peripheral Options 53

5.5.5 Day/Night Settings 61

5.6 Circuit Options 67

5.6.1 Signalling Line Circuit (SLC) - Devices 67

5.6.2 Signalling Line Circuit (SLC) - Learn 77

5.6.3 On-Board Circuits 79

5.7 Control-By-Event Output Rules 81

5.7.1 Output Type 84

5.7.2 Filter-by-type 85

5.7.3 Evacuation 86

5.7.4 Silence 86

5.7.5 Interrupt Delay 87

5.7.6 Class Change 87

5.7.7 Two Zone 88

5.7.8 Zones 89

5.7.9 Device Inputs 90

5.7.10 Soak Timer 91

5.8 Zone Texts 91

5.9 Access Options 92

5.10 System Options 93

5.10.1 Crystal Frequency 94

5.10.2 Wipe Memory 95

5.11 Normal 95

Appendix 1 - Specification A1-1 to A1-6

Appendix 2 - ID60 Single Loop Panel

Differences A2-1 to A2-5

Appendix 3 - Fault Messages & Meanings A3-1 to A3-4

Appendix 4 - EN54-2 Options with

Requirements A4-1 to A4-4

Appendix 5 - Configuration of a Fault Routing

Output Using a Zone Monitor A5-1

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

1997-263-000-11, Issue 11

January 2010

1 Introduction

1.1 Manual Purpose

The purpose of this manual is to provide the user with all

recommended procedures and full technical details for

the successful installation, commissioning and

programming of a NOTIFIER ID50 Series Panel.

The descriptions and procedures also apply to the

NOTIFIER ID60 panel. Differences between the ID50 and

ID60 panels are given in Appendix 2.

Procedures described in this manual include appropriate

warnings and cautions to guide the user towards adopting

safe and methodical work practices during the installation,

commissioning and programming phases.

The ID50 Series panels support OPAL protocol devices.

These devices support both OPAL and CLIP loop polling

protocols so they can be added to an existing CLIP

protocol loop. However, when OPAL protocol is enabled

on a loop a maximum of 10 CLIP device addresses can

be supported as part of the total of 99 sensors and 99

modules.

Important Note

This manual must be read, and its content clearly

understood, before proceeding with any work relating to

the ID50 Series Panel. Damage to the control panel may

result from NOT following the recommended procedures

described in this manual.

This manual provides all necessary instructions for the

ID50 Series Panel and applies only to fire panels fitted

with compatible software.

CAUTION: In particular, care must be taken when

powering up/down any repeaters.

If there are any areas of doubt, consult your supplier

before continuing with the system installation,

commissioning and programming.

1.2 System Design and Planning

It is assumed that the system, of which the ID50 Series

Panel equipment is a part, has been designed by a

competent fire alarm system designer in accordance with

the requirements of EN54 Part 14 and any other local

codes of practice that are applicable.

The design drawings should clearly show the positions

of all the ID50 Series Panel control equipment and field

devices.

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

2997-263-000-11, Issue 11

January 2010

1.3 General

The ID50 Series Panel is designed for use with

NOTIFIER’s range of addressable analogue sensors,

control and monitoring modules and addressable call

points. Aunique signalling protocol is used, having digital

address and control signals and analogue pulse width

monitoring for the reply data from devices.

The serial communications interface operates under

RS485 protocol and enables communications between

the fire panel and repeaters.

While every effort is made to ensure the accuracy of the

content of this manual, the manufacturer reserves the

right to change the information without notice.

Installation

The ID50 Series Panel is easy to install providing the

recommended procedures described in this manual are

followed. To avoid inadvertent contamination of the PCB

Assembly, the manufacturer recommends it be installed

in the back box only after all other trades have completed

their tasks.

Commissioning

To commission the ID50 Series Panel, follow the

recommended procedures described in this manual. The

manufacturer recommends that during commissioning

and maintenance, ALL RS485 signal cables are

disconnected at the Panel end, BEFORE powering down

the system and are connected AFTER powering up the

system.

Configuration

To configure the panel and system, carefully read and

follow the procedures given in this manual. These

procedures describe the menus that are displayed on

the Liquid Crystal Display (LCD) Unit.

Refer to the ID50 Series Operating manual (ref: 997-

264-000-X) for a description of compatible addressable

Signalling Loop Circuit (SLC) analogue devices.

1.3.1 Date-dependent Functions

The calendar end date for this product is 31/12/2063

(two thousand and sixty-three) and it will perform correctly

up to this date.

The calendar function has not been tested beyond

this date.

1.4 CE Marking

This panel is CE Marked to show that it conforms to the

requirements of the following European Community

Directives:

Only fit the electronics

module after all the other

trades have completed

their tasks!

Only suitably-qualified

engineers must install,

commission and

configure this product.

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

3997-263-000-11, Issue 11

January 2010

The EMC Directive 2004/108/EEC, by the application of

the following EMC Standards:

EN 61000-6-3: Electromagnetic Compatibility (EMC)

Generic emission standard for Residential,

Commercial and Light industrial environments

EN 50130-4: EMC Product family standard: Immunity

requirements for components of fire, intruder and

social alarm systems.

Low Voltage Directive 2006/95/EEC, by the application

of the safety standard:.

EN 60950-1: Safety of information technology

equipment.

The Construction Products Directive 89/106/EEC, by the

application of the following standards:

EN 54-2:1998, (Amd. 1 & 2): Fire detection and fire

alarm systems - Control and indicating equipment.

EN 54-4: 1998 (Amd. 1 & 2): Fire detection and fire

alarm systems - Power supply equipment.

1.5 EN54 Functions

This fire control panel is designed to comply with the

requirements of EN 54 Part 2/4. In addition to the basic

requirements of EN 54-2, the panel may be configured to

conform with the following optional functions - the applicable

clauses of EN 54-2 are referenced as follows:

Options Clause

Indications:

Fault signal from fire protection equipment 7.10.4

Recording of the number of entries

into fire alarm condition 7.13

Fault signals from points 8.3

Controls:

Delay to Outputs 7.11.1

Manual or automatic switching of delays to outputs 7.11.2

Dependency on more than one alarm signal, Type B 7.12.2

Disablement of each address point 9.5

Test condition 10

Outputs:

Fire alarm device(s) 7.8

Fire alarm routing equipment 7.9.1

Fire alarm routing equipment with alarm confimation 7.9.2

Automatic fire protection equipment: Type A 7.10.1

Automatic fire protection equipment: Type C 7.10.3

Fault warning routing equipment 8.9

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

4997-263-000-11, Issue 11

January 2010

1.6 Ancillary Functions

The following is a list of ancillary functions that are

provided by the ID50 Series panel in addition to the those

required by EN54-2/4. These functions are described in

the section of this manual as referenced (except those

marked thus ‘*’ which are described in 997-264-000-X,

ID50 Series Panel - Operating Manual):

Ancillary Manual

Functions Section Refs.

Site Specific Setup Options 5.5

Access Options 5.9

Voltage Indications *4.12

Control-by-Event 5.7

Output modes 5.7.1

Input type pattern 5.7.9

Disable/enablement *4.9

Repeater interface 2.7

Self-learn configuration - manual 5.6.1

Self-learn configuration - auto 5.6.2

Module supervision options 5.6.1

Module silence options 5.7.4

Text editing 5.8

Sensor LED blinking on/off 5.5.3.4

Bell pulsing ratio 5.5.3.5

Display of alarm count *4.11.6

Extend delay timer 5.5.5.3

Sounder Volt-free contact options 4.4.5

Relay drive output option 4.4.6

Extinguishing system features 5.5.3.7, 5.5.3.8, 5.5.3.9,

5.7.1, 5.7.2, 5.7.10

CAUTION:

This product is not compliant

with EN 12094-1.

12094-1

Fire extinguishing installations in

Europe are required to be certified as

compliant to this standard.

The following features are provided by the Power Supply

Unit (PSU) of the ID50 Series Panel to comply with EN 54-4.

Features of the ID50 EN54-4

Power Supply Unit (PSU) Clause

Derive power supply from main power source 5.1

Derive power supply from and monitor a

standby battery source 5.2

Charge and monitor the standby

battery source 5.3

Detect and signal PSU faults 5.4

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

5997-263-000-11, Issue 11

January 2010

1.7 Related Documents

This manual only describes the installation,

commissioning and configuration of the ID50 Series

Panel. All operating functions are covered by the:

ID50 Series Panel Operating Manual (ref:

997-264-000-X)

The Panel can support repeaters via the RS485

communications link. This manual does not provide

details about the repeaters or Compact Mimics; these

are described in:

IDR-2A, -2P & -6A Repeaters User Manual

(ref: 997-411-000-X).

IDR Mimic Installation and Commissioning Manual

(ref: 997-412-000-X).

Compact Mimic Installation Instructions (ref. 997-497-

000-X).

Note: The ‘000’ part of the manual reference is the UK

country code for the manual.

The ID50 Panel can also support the VIEWTM sensor. This

manual does not attempt to cover all the VIEWTM sensor

programming and calibration issues as these are

described in some detail in the following, which is available

from NOTIFIER’s Technical Support Department:

VIEWTM Application Guide (ref: 997-198).

1.8 Warnings and Cautions

Where appropriate, the manual includes advisory

warnings and cautions to remind you to consider safety

at all times, especially when following the procedures

described herein.

You are alerted to any areas where high voltage [i.e. non-

Safety Extra-Low Voltage (SELV)] is present, or where

there may be a risk of damage to static-sensitive devices

if the recommended procedures described in this manual

are not followed.

An example of a high voltage warning and an anti-static

caution is provided to the left of this paragraph.

The ID50 Series Panel incorporates some features

which, if used inappropriately, may contravene the

requirements of EN 54. Where there is a possibility of

such an occurrence, a suitable warning is given with brief

details of the EN 54 requirement. A typical EN 54 non-

compliance warning is illustrated at left.

1.9 Tips

‘Handy tips’ are included, where appropriate, to assist

you in following quick and safe procedures for fire

detection system installation and integration.

Look for the ‘TIP!’ icon and supporting text, typically

illustrated at left.

Magnetise the tip of your

screwdriver to help when

offering small screws to

holes in confined spaces.

WARNING: High Voltage!

Take suitable precautions to

avoid electric shock

EN54-2:-8.8

One hardware-

configurable output

must be configured

as a fault relay

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

6997-263-000-11, Issue 11

January 2010

1.10 Glossary of Icons

Throughout this manual, and the other related ID50

Series Panel manuals, a number of icons are used either

as part of the illustrated process descriptions, or in the

main text to help clarify, or simplify, particular

configuration procedures.

The following icons are used to advise or indicate:

a. DO follow the recommended procedure or method.

b. DO NOT use this procedure or method.

c. Inspection of an item or sub-assembly is required at

this point.

d. Following a defined process meets/ does not meet

the required approval/inspection criteria or standards.

e. Additional items to be considered.

f. This icon placed next to a pushbutton requires you to

press it while configuring the panel. Where two or

more icons are used, a number may be placed on or

near each hand to indicate the order of selection: 1

coming before 2.

g. Activity process step - flow arrow for single action or

iterative actions.

h. Leader arrow - used with activity processes.

i. Internal buzzer operating/not-operating or silenced.

j. Sounder operating/not-operating or silenced.

k. Power connected and switched ON/disconnected and

switched OFF.

l. Manual Call Point (MCP)/Sensor.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Honeywell Pannello di controllo

Honeywell

Honeywell HCM 200 Manuale utente

Honeywell

Honeywell Notifier AFP-3030 Manuale utente

Honeywell

Honeywell Silent Knight IFP-2000 Module 3 Manuale utente

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manuale utente

Honeywell

Honeywell NOTIFIER INSPIRE E10 Manuale di formazione

Honeywell

Honeywell NOTIFIER AM-8200 Manuale del proprietario

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manuale utente

Honeywell

Honeywell MM3-MASTERTROL MM-3 Manuale tecnico

Honeywell

Honeywell Notifier NFS2-640/E Manuale del proprietario

Honeywell

Honeywell LT-32 Manuale utente

Honeywell

Honeywell TrolATemp TZ-3 TotalZone Manuale operativo

Honeywell

Honeywell Galaxy Dimension series Guida rapida alla configurazione

Honeywell

Honeywell MINI-ZONE 69-1361 Guida rapida

Honeywell

Honeywell Galaxy Flex Guida utente

Honeywell

Honeywell Vigilon Plus Manuale utente

Honeywell

Honeywell Notifier NFS-320 Manuale utente

Honeywell

Honeywell Excel 5000 System Series Manuale utente

Honeywell

Honeywell Notifier ST.PL4+ Manuale utente

Honeywell

Honeywell Vigilon 4 loop Manuale di installazione e funzionamento

Honeywell

Honeywell W834A Manuale utente

Honeywell

Honeywell ADEMCO VISTA SERIES Guida all'installazione

Honeywell

Honeywell Notifier NFS-320 Manuale utente

Honeywell

Honeywell Accenta Manuale utente

Honeywell

Honeywell HPZC10 Series Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche