Honeywell Domonial CMI Series Guida utente

02/2011

Domonial CMI/CME

Installer’s manual 3

Manuel d’installateur 27

Page 2 of 52

02/2011

Page 3 of 52

02/2011

Contents

Introduction............................................................................................. 5

Installation procedure.............................................................................. 7

Plan the installation ................................................................................. 8

Mount the panel .................................................................................... 10

Wire the panel ....................................................................................... 11

Mount, register and programme devices ............................................... 13

Set the date and time............................................................................. 14

Save the configuration ........................................................................... 14

Test the installation ............................................................................... 15

Exit programming mode......................................................................... 16

Fit the panel cover ................................................................................. 16

Test after arming the system ................................................................. 18

Specification .......................................................................................... 19

List of codes ........................................................................................... 21

Page 4 of 52

02/2011

Page 5 of 52

02/2011

Introduction

Domonial is a wireless control panel with a built-in siren, digital communicator and audio

verification system. The radio link between the various components of the system allows easy

installation with only a small amount of cabling (mains, and when specified, PSTN, X10 or a wired

intercom terminal). This version can be used with the HF and the M wireless device ranges, for

example DO800M.

After recording a wireless Audio device, all HF wireless device can not work your installation.

Domonial can be programmed using the following tools:

DOMOPC programming tool. Refer to the DOMOPC online help guide for full details.

A TCU keypad

This guide describes how to program the panel using a TCU keypad. A complete list of

programming codes is provided at the end of this manual.

Panel Label

Commercial reference

Product file reference

Serial number Note: The format of

Date of manufacture date is yymmdd

The software version number is marked on a label on the box containing the panel (e.g. SW: L06) and

on a small label on the PCB.

The LED Indicators

The panel comes in two designs, depending on the version. Both designs have LED indicator lights

showing the status of the system.

LED latout for the classic version

State/LED

Mains Supply

Arm/Disarm

Perimeter

Fault

Intruder Alarm

Memory

Technical

Alarm Memory

Colour

Green

Yellow

Red

LED latout for the EN version

State/LED

Mains Supply

Fault Area

System Fault

Tamper Fault

Intruder Fault

Colour

Green

Yellow

Red

CMI8UK-STD-7

97AGC0B

75000C6C8

100320

Page 6 of 52

02/2011

System operation

Once installed the Domonial alarm allows the surveillance of three different areas per site:

Area A = the perimeter or ground floor

Area B = the rest of the house

An optional Area C. The configuration of Area C depends upon the general

parameters “Annex arming linked to Total” and “Annex disarming linked

to Total”

Total set (all devices in the house –equivalent to Away in the UK)

Part set (a subset of the total set, usually installed as perimeter devices –

equivalent to Home in the UK)

Annex set (an additional set of devices, for example a second perimeter or

a garage –not generally used in the UK)

Arming and disarming

arming and disarming can be performed using:

Keypads and keyfobs, which can be associated with total or part sets, the annex set, or all

sets.

DTMF codes over the phone.

programming tools. This function is available depending on product version and country

regulations

Users

Keyfobs, keypads and codes, with which to access the alarm system, can be assigned to

a maximum of 10 users (including a master user). Each user can have a code and/or

a TAG for each keypad.

System operation by users can be detected, stored and reported to the monitoring station. In

addition, Domonial can be programmed to take a set of pictures when the system is armed or

disarmed that are sent to the monitoring station. Dedicated profiles for limited time access

and clocking are also available on some versions of the product.

Alarm detection

The access route devices can be set up as follows:

Immediate: direct trigger, a device is outside the access route

Delayed: with an entry/exit delay programmable from 0 to 90 seconds

(for total, part or annex areas)

Mixed: direct trigger or delayed if a delayed device was activated first.

Technical devices, such as a flood/temperature sensor, are permanently armed and trigger

independently of arming status.

Page 7 of 52

02/2011

Alarm signalling

The following sounder operating modes can be programmed:

Standard siren

Siren activated after intrusion or after intrusion and PSTN failure

Siren activated on tamper detection only when system is armed or independent

of arming status

Siren activated on fire detection

Intruder siren duration can be programmed to a maximum of 4 minutes.

Activation of the sounder can also be postponed until after the alarm signal has been transmitted.

Fire siren duration is fixed to 5 minutes and can be delayed for up to 5 minutes.

Alarm transmission

Domonial is equipped with a digital transmitter for sending information via PSTN, optional

GSM/GPRS card, or optional Ethernet card to the following:

A telephone (PSTN, GSM voice)

An Alarm Receiving Centre using the following protocols: Secom3, Surtec, Cesa, Contact ID

Note: Data networks, such as GSM data or GPRS, use the SECOM3 protocol.

Installation procedure

The rest of this manual is designed to be followed in sequence and describes the following

main tasks:

Equipment siting (planning and installation)

Registration of wireless devices

Basic programming

Device and alarm testing

Contents of the box

Check that your Domonial box contains the following:

Domonial alarm panel, plus the User Manual

1 Stocko, four-pin connector inside the panel for the telephone connection

Breakout tabs for covering unused wire passages

A Velcro strap for securing the battery

A 4 V 3.5 Ah back-up battery is required, and is sold separately by Honeywell: part numbers

ELECKSON BPEL040035 or SONNENSCHEIN A504/3.5S.

Page 8 of 52

02/2011

Plan the installation

To ensure the installation process is successful we recommend that you mark the position

of the system components on a drawing of the building.

A layout drawing is shown on the following page to help you plan the wiring into and out

of the panel.

Select positions for the panel and peripheral devices to maximise GSM signal level (if used),

audio coverage (if used), and wireless radio signal levels.

Note: Radio transmission is attenuated when sent through wood, Artex, brick, concrete, and steel

reinforcements. It is reflected by metal surfaces such as mirrors, steel sheeting, aluminium steam-

arrestor, and fine-mesh wire-netting.

Avoid these locations:

Metal objects, for example water tanks

230 VAC cables or consumer units

Close proximity to loud speakers

When used, the telephone line to the control panel must be as discrete as possible, and guarded

by a detector.

To ensure that alarm transmission takes priority over other telephone communications, always

position the panel after the exchange line and before all telephone extensions in the home.

If the site is equipped with an ADSL line, use a central ADSL filter after the exchange line

to separate telephone extensions and ADSL extensions.

For mains connection, the panel can be connected either via a socket outlet or directly to

a fused outlet.

Page 9 of 52

02/2011

Panel internal layout and connections

1 mounting holes

2 mains connector (J1)

3 X10 connector (J9)

4 output voltage (J8)

5 PSTN connector (J2)

6 optional plug-in module, if fitted

(GSM/GPRS card shown)

7 SIM holder (GSM/GPRS module only)

8 tamper switch

9 status LEDs

10 RJ45 connector

11 microphone

12 external audio enable (J11)

13 call button

14 external antenna power (J14)

15 external antenna connector (J15)

16 external audio power and external

tamper connector (J6)

17 external audio connector (J7)

18 internal antenna

19 built-in speaker

20 battery compartment

Page 10 of 52

02/2011

Mount the panel

Prior to starting the installation process call your alarm receiving centre (ARC) and ask them to

ignore any alarms during the installation and setup process.

WARNING: MOUNT THE PANEL SO THE BATTERY TERMINALS ARE AT THE

TOP. ANY OTHER ORIENTATION MAY RESULT IN LEAKS FROM THE BATTERY.

1. Remove the cover from control panel.

2. Hold the panel in its selected mounting position and mark the mounting hole locations, using

the panel as a template.

Note: Ensure the wall is flat enough to compress the tamper switch spring. Use fixings

adequate to support the weight of the panel and battery.

Caution: Do not drill holes with the panel in place.

3. Remove the panel from the wall and drill the mounting holes.

4. Insert the battery in the panel, and then

secure it with the Velcro strap as shown.

Caution: Do not connect the battery

until later.

5. If it is required, install a GSM/GPRS module

(shown), or Ethernet module, in the dashed

area on the drawing.

6. If using GSM communications, fit a SIM card

as shown.

7. Feed the mains and phone wiring through the base of panel, and screw the panel to the wall.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Honeywell Pannello di controllo

Honeywell

Honeywell Notifier RP-2001 Manuale utente

Honeywell

Honeywell ENVIRAZONE PANEL W8835 Manuale operativo

Honeywell

Honeywell TrueZONE HZ432K/U Manuale utente

Honeywell

Honeywell Notifier SFP-2402 Manuale utente

Honeywell

Honeywell DeltaNet FS90 Manuale utente

Honeywell

Honeywell IFP-2100ECS Specifiche tecniche

Honeywell

Honeywell 013080 Manuale di istruzioni

Honeywell

Honeywell HCM 200 Manuale utente

Honeywell

Honeywell Farenhyt Series Manuale tecnico

Honeywell

Honeywell TrueZONE HZ432 Manuale utente

Honeywell

Honeywell MS-9200UDLSE Manuale utente

Honeywell

Honeywell SILENT KNIGHT 6700 Manuale utente

Honeywell

Honeywell W8835A Manuale utente

Honeywell

Honeywell 5110XM Manuale utente

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manuale utente

Honeywell

Honeywell Securit 800L Manuale utente

Honeywell

Honeywell Fire-lite ECC-LOC Manuale utente

Honeywell

Honeywell NOTIFIER RP-2002C Manuale utente

Honeywell

Honeywell Notifier ST.PL4+ Manuale utente

Honeywell

Honeywell AQ25A Series Manuale utente

Honeywell

Honeywell Notifier NFS-320 Manuale utente

Honeywell

Honeywell Gamewell-FCI GWF-7075 Manuale utente

Honeywell

Honeywell AQ250 Series Manuale operativo

Honeywell

Honeywell W-MMF Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche