Honeywell 10260S series Guida

62-86-33-26 Page 1 of 5

10260S Series Actuators

Auto-Manual Switch Replacement Instruction

Document Number

Form: 62-86-33-26

Effective: 06/01

Supersedes: none

Overview

These instructions apply to the following kit: 51500581-501 Auto-Manual Switch Kit and its application to

the 10260S Series Actuators.

Summary

The AUTO-MANUAL switch of the 10260S Actuator is used as a manual override to drive the actuator

motor to position during set up. The Auto-Manual switch kit contains the components needed to add the

switch function to your actuator, or replace a defective switch. Follow the procedure in Table 1 to install the

Auto-Manual switch.

Tools Needed

To perform the replacement procedure, you will need the following tools:

•Medium Flat-blade screwdriver

•Medium Phillips screwdriver

•Small jeweler’s screwdriver set

•Small adjustable wrench

•Needle-nosed pliers

•Heat gun

Procedure

WARNING

Disconnect power before accessing components inside the actuator.

ATTENTION

When working with Printed Wiring Assemblies (PWAs) always protect against electrostatic discharge by

wearing a grounded wrist strap.

Auto-Manual Switch Instruction, continued

Page 2 of 5 62-86-33-26

AUTO-MANUAL

Switch

Terminal Panel

Figure 1 AUTO-MANUAL Switch Location

Table 1 AUTO-MANUAL Switch Installation Procedure

Step Action

1 Remove AC power to the actuator.

2 Remove four screws and the terminal panel cover from the actuator. See Figure 1

3 Remove two screws and pull out the terminal panel from the actuator case.

NOTE: It may be necessary to loosen the external cable entrance on the side of the actuator case to

gain greater access to the AUTO-MANUAL switch location behind the terminal panel.

Procedure continued on next page

⇒

Auto-Manual Switch Instruction, continued

62-86-33-26 Page 3 of 5

Step Action

4 If replacing the switch, disconnect switch wires and remove switch:

•Carefully disconnect auto-manual switch wires at the rear of the terminal panel from the following

lugs: TB1-1, TB1-8,

TB1-9, TB2-12,

TB2-13, TB2-10, TB2-11.

(Looking at the rear of the terminal panel - TB1 is the top terminal board. TB1-1 is the rightmost

terminal on the top terminal board.)

•Disconnect auto-manual switch wires from the connector at P6-1 and P6-2 on the main PWA.

•Remove switch knob by loosening the set screw and then sliding it off the shaft.

•Remove nut securing switch to side of case.

•Pull switch out of case.

5 Slide heat shrink tubing over the body of the new switch so it covers the soldered wire terminals. With

a heat gun, apply hot air to the shrink tubing to seal the wire terminals of the switch.

6 Install new switch:

•Remove plug from access hole in actuator case, (if present) where switch shaft will be installed.

See Figure below.

•.Attach switch label to side of case.

•Remove nut from threads on switch. Insert switch shaft through case access hole. Carefully

rotate switch until is seats in case. Make sure the stub engages the small hole.

•Screw the nut onto the switch shaft and tighten it securely.

•Attach knob to shaft with set screw on flat side of shaft.

AUTO-MANUAL

Switch

Nut

Knob

Label

7 Identify the correct terminal lugs on the back of the terminal panel for connecting the switch wires.

Procedure continued on next page

⇒

Auto-Manual Switch Instruction, continued

Page 4 of 5 62-86-33-26

Step Action

8 Connect switch wires:

•If adding (not replacing) the switch, remove blue and orange wires from TB1-8 and TB1-9.

Connect blue wire to TB2-13 and orange wire to TB2-12.

•If adding or replacing the switch, one at a time connect auto-manual switch wires as follows:

AUTO-MANUAL

Switch Wires

TO: Terminal Panel Lugs

Black

White

Brown

Green

Violet

Orange

Red

TB1-1

TB1-8

TB1-9

TB2-12

TB2-13

TB2-10

TB2-11

Red (24 AWG) Æ

White (24 AWG) Æ

TO: Main PWA Connector

P6-1

P6-2

NOTE: Some terminal lugs have dual (piggyback) wires attached; make sure the wires are attached to

the correct terminals. Make sure piggyback wires on outermost terminals are facing the inner

terminals, not facing away from the terminals. For example, TB1-1 should have its piggyback terminal

positioned between TB1-1 and TB1-2.

9 Reinsert the terminal panel back into the actuator case being careful not to pinch any wires. Secure

terminal panel with two screws.

10 Install a new gasket and replace the terminal panel cover. Secure with four screws.

11 Reapply AC power to the actuator.

12 Verify actuator configuration and check AUTO-MANUAL switch for correct function.

13 Return actuator to service.

Auto-Manual Switch Instruction, continued

Sensing and Control

Honeywell

11 West Spring Street

Freeport, IL 61032

62-86-33-26 06/01 Printed in USA www.honeywell.com/sensing

Warranty/Remedy

Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship.

Contact your local sales office for warranty information. If warranted goods are returned to Honeywell

during the period of coverage, Honeywell will repair or replace without charge those items it finds defective.

The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied,

including those of merchantability and fitness for a particular purpose. Specifications may change

without notice. The information we supply is believed to be accurate and reliable as of this printing.

However, we assume no responsibility for its use.

While we provide application assistance personally, through our literature and the Honeywell web site, it is

up to the customer to determine the suitability of the product in the application.

Indice

Altri manuali Honeywell Controllori

Honeywell

Honeywell HR 10 F Manuale utente

Honeywell

Honeywell V7335A 2000 Series Manuale utente

Honeywell

Honeywell HJK7000 UltraKey Plus Manuale di istruzioni

Honeywell

Honeywell ML6421 Manuale operativo

Honeywell

Honeywell CN34 Series Manuale operativo

Honeywell

Honeywell HC900 Guida utente

Honeywell

Honeywell LKS 310 Manuale

Honeywell

Honeywell HR 40 Manuale utente

Honeywell

Honeywell SP10K Manuale utente

Honeywell

Honeywell V8200 Manuale utente

Honeywell

Honeywell CIPer 50 Manuale di installazione e funzionamento

Honeywell

Honeywell Spyder 5 Manuale utente

Honeywell

Honeywell HVC0001 Manuale utente

Honeywell

Honeywell D6 PRO Manuale utente

Honeywell

Honeywell ControLinks R7999A Manuale utente

Honeywell

Honeywell DBC2000E10 Series Manuale utente

Honeywell

Honeywell DC1000 SERIES Manuale utente

Honeywell

Honeywell R7515C MacroCel Manuale utente

Honeywell

Honeywell Elster Jeavons J125 Manuale utente

Honeywell

Honeywell Lyric LCP300-LC Scheda informativa del prodotto

Honeywell

Honeywell UDC2800 Manuale utente

Honeywell

Honeywell AUTOMATIC CONTROL Manuale di installazione e funzionamento

Honeywell

Honeywell T7560B Manuale utente

Honeywell

Honeywell LYNX Touch Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente