Honeywell Rae SensorRAE 4R+ Manuale utente

The SensorRAE 4R+ is a storage case for non-EC (electrochemical) sensors and a warm-up station for EC sensors that

keeps them in a ready-for-use state. The water-resistant (IP-67) case accommodates six sensors and when used to warm

up sensors, its four AAA batteries typically last for six months.

Inserting/Replacing Batteries

CAUTION! Never change batteries or sensors in an area known to be hazardous.

The SensorRAE 4R+ uses fourAAAalkaline batteries (Duracell MN2400) to warm up sensors requiring it. If you are

using the SensorRAE 4R+ to carry sensors that do not require warming up, then there is no need for batteries.

The batteries are installed on the bottom of the interior unit. Grip the small tab at one end of the unit and then pull up to

lift the unit out of the SensorRAE 4R+’s compartment.

If batteries are already installed and require replacement, remove them. Then install new ones, being careful to match

the batteries’ direction to the polarities indicated by “+” in the battery holders.

Testing The Batteries

Press the button on the right side of the panel. The 5-segment LED ladder indicates the batteries’strength.

When the batteries are almost depleted, the bottom red LED flashes once per second. Any sensors undergoing

conditioning are still powered on. (Press the button to check the sensor state.)

When the batteries are completely depleted, all five red LEDs flash once per second, in sequence from top to bottom.

Any sensors undergoing warm-up are powered off. Therefore, those sensors will require warm-up time after the

batteries are changed.

Red LEDs on

Remaining capacity

80% to 100%

60% to 80%

40% to 60%

20% to 40%

0% to 20%

SensorRAE 4R+

User’s Guide

Press

Inserting Sensors

Important! Always make sure your hands are clean and dry before handling sensors.

Place a sensor into a socket, aligning it with the matching keyways and the multi-pin connector at the bottom. Once a

sensor is plugged in, its corresponding green LED flashes once and if it requires warm-up, then warm-up begins. Below

are approximate times for sensor warm-up.

Non-EC sensor: 0 hours (no warm-up required)

Non-biased EC sensor:6 hours

Biased EC sensor:24 hours

If the green LED does not blink, the sensor is not inserted properly.

Note: If the sensor is properly seated and you remove it at any time during its warm-up, it must be returned to its socket

within 20 seconds, or the SensorRAE 4R+ will restart the warm-up cycle from the beginning.

Removing Sensors

Always lift sensors out with your fingers, gripping around the sides.

Checking Sensor Status

You can check the status of a sensor being warmed up by pressing the power button. If the green LED next to the

sensor glows, it is fully conditioned and ready for use.

RAE Systems by Honeywell

World Headquarters

3775 N. First St.

San Jose, CA 95134-1708 USA

Phone: 408.952.8200

Fax: 408.952.8480

E-mail: customerserv@raesystems.com

Web Site: www.raesystems.com

Rev. A

February 2012

P/N T03-4001-000

Multi-pin Connector

Bottom

View

Top

View

Alignment keys

Sensor inserted

Alignment keyways (6x)

LED blinks once to

indicate

sensor has

been inserted correctly

Indice

Altri manuali Honeywell Hardware di rete

Honeywell

Honeywell MAXPRO 2.5 Manuale utente

Honeywell

Honeywell MAXPRO NVR SE Manuale utente

Honeywell

Honeywell MAXPRO NVR SE Manuale utente

Honeywell

Honeywell HDCD8TP Manuale utente

Honeywell

Honeywell 057810 Manuale utente

Honeywell

Honeywell Internet Connection Module Manuale utente

Honeywell

Honeywell MAXPRO NVR XE Manuale utente

Honeywell

Honeywell HEN04111 Manuale utente

Honeywell

Honeywell 30 Series Manuale utente

Honeywell

Honeywell FUSION STREAMER Manuale utente

Honeywell

Honeywell MAXPRO NVR Hybrid SE Manuale utente

Honeywell

Honeywell TotalPlant LCN Guida utente

Honeywell

Honeywell Mesh Router Manuale utente

Honeywell

Honeywell Notifier NFN-GW-EM-3 Manuale utente

Honeywell

Honeywell Embedded NVR Manuale di istruzioni

Honeywell

Honeywell nfs2-3030 Manuale tecnico

Honeywell

Honeywell MAXPRO NVR 3.1 Manuale utente

Honeywell

Honeywell 2450Cm Series Manuale utente

Honeywell

Honeywell 35 Series Manuale utente

Honeywell

Honeywell hus-nvr-1032-e Manuale utente

Honeywell

Honeywell 4909 CPVC Manuale utente

Honeywell

Honeywell MAXPRO NVR SE Series Manuale utente

Honeywell

Honeywell 2450Cm Series Manuale utente

Honeywell

Honeywell LonWorks protocol Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente