Honeywell DF-RC Manuale utente
DF-RC
Honeywell
Manual
RF Remote Control Decorative Fire
2
Key Up
Key Down
Key Stop/Stand-by
Key Menu
Display
DISPLAY AND KEYS
3
Display
Manual operation.
Time schedule active.
Active time period.
Closed (left) or open fire place type (right).
Decorative fire is on.
Decorative fire can be ignited.
Fault of decorative fire can be reset.
Burner off/setting down (left), burner on/setting up (right).
Busy (for instance while decorative fire is been ignited).
Fault.
Main plug of the decorative fire is plugged in the other way round.
RF-communication.
Batteries are almost empty (symbol flashes).
Time representation (24-hours or 12-hours).
Days of the week. Square indicates actual day.
Temperature representation.
Temperature sensor(s) are defect.
Keys
Enhance setting or change selection.
Lower setting or change selection.
Choose menu and menu selection.
Stop setting menu or go to stand-by.
4
SET UP FOR OPERATION
The RF remote control makes it possible to operate your decorative fire
both manual as by means of a time schedule.*
The temperature and the flame height can be manually controlled. The
time schedule only controls the temperature.
The possible time schedules are*:
A time schedule with the same settings for each day.
A time schedule with separate settings for the week days (monday to
friday) and the weekend.
A time schedule with separate settings for each day.
For each day, two, four or six different time periods can be set.*
The time schedule can easily be set by setting the begin time and the
temperature set point of each period.
Flame Symbol
A flame symbol indicates that the burner of your decorative fire has been
switched on.
Batteries
Before you can take the RF remote control in operation, the two supplied
batteries (type AA) have to be placed. After the batteries have been
placed, the RF remote control is ready for manual operation with flame
height control. To save batterie life, some time after the last key pressure,
the display goes blanc*, unless the decorative fire is switched on.
* The availability of the option depends on the factory setting of the
decorative fire.
•
•
•
5
Binding RF Remote Control
The RF remote control can only communicate with a decorative fire after
the RF remote control has been bound with that decorative fire.
If both devices are switched on within 5 minutes after each other, the
binding goes automatically.
This display is shown if the RF remote control has
not been bound. The symbol flashes. Make
sure the decorative fire has not been switched on
for more than 5 minutes and start the binding as
follows:
Press keys and simultaneously.
The display below is shown.
This display is shown during binding. The symbol
flashes. When the binding is finished, the default
display is shown.
Note: In case of replacement of the decorative fire or the RF remote
control, the binding has to be initiated manual, see Binding RF
remote control, on page17.
Time and Day
The time schedule of the RF remote control can only be used if the
time has been set. The time and day can be set in the User Menu, see
Setting Time and Day on page 13. The time representation, 12-hours or
24-hours, can be set in the Installation Menu, see Choice 12- or 24-
Hours Representation on page 15.
6
OPERATION
The RF remote control is equipped with a display and four keys. Because
of this the decorative fire can be easily operated and settings easily be
adjusted.
There are two setting menus available:
User menu
Installation menu
Press key once to select the User menu, or keep key pressed for
ten seconds to select the Installation menu.
Manual Operation
Dependent on the choice made in the User menu, the temperature or the
flame height can be controlled manual.
Flame height control
The decorative fire must be manually switched on and off.
Igniting decorative fire
Press keys and simultaneously if the
adjacent display is shown.
•
•
7
This display is shown. The symbols and
are flashing to indicate the decorative fire is being
ignited.
After the decorative fire has been ignited, the
display below is shown.
The flame height can now be manually controlled.
Setting flame height
Press key or once. The display below is shown.
The value of the current flame height flashes.
Set the required flame height by pressing key
or . Dependent on the key pressed, the symbol
or is shortly visible on the display. The flame
height can be set between1 and 15.
Wait a few seconds or press key to leave the menu.
Note: The flame height can only be controlled if the decorative fire has
been switched on.
8
Switching off the decorative fire
Press key once to switch off the decorative fire.
This display is shown. The symbol flashes to
indicate the decorative fire is being switched off.
After the decorative fire has been switched off, the
default display is shown again.
Temperature control
The decorative fire is automatically switched on and off according to
the heat demand. Press key or once to adjust the required
temperature. The display below is shown.
The current temperature set point flashes. Set
the required set point by pressing key or .
Dependent on the key pressed, the symbol or
is shortly shown on the display. The temperature
can be set between 7,0 and 35,0 °C.
Wait a few seconds or press key to leave the menu.
9
Temporarily interrupting temperature control
When temperature control is used, the decorative fire can temporarily be
switched off.
Press key once to switch off the decorative fire.
This diplay is shown. The symbol flashes to
indicate the decorative fire is being switched off.
After the decorative fire has been switched off, the
display below is shown.
The symbol flashes to indicate the
decorative fire has to be ignited manually by
pressing the keys and simultaneously.
When the decorative fire is ignited again, the
temperature control becomes active.
Note: The temperature set point can not be changed during the
temporarily temperature control interruption.
10
Time Schedule
The temperature is controlled according to the time schedule, see Setting
Time Schedule on page 14. The decorative fire is fully automatically
ignited and switched off.
Temporarily changing the temperature set point
The temperature set point of a time schedule period can temporarily be
enhanced or lowered. Press key or once to set the temporarily set
point. The display below is shown.
The current temperature set point flashes. Set
the temporarily required temperature set point
by pressing key or . Dependent on the key
pressed, the symbol or is shortly shown on
the display.
Wait a few seconds or press key to leave the menu.
This display (example) is shown. The symbol
indicates that the temperature set point has been
adjusted manually.
The temporarily adjustment can be undone by setting the manually
adjusted set point back to the set point of the current time period. In
case of a transition to a new time period, the temporarily adjustment is
cancelled automatically.
Indice
Altri manuali Honeywell Telecomando
Honeywell
Honeywell EXCEL 5000 OPEN ZAPP Manuale utente
Honeywell
Honeywell TrueIAQ Manuale utente
Honeywell
Honeywell 5834-4 Istruzioni operative
Honeywell
Honeywell 40015 Manuale utente
Honeywell
Honeywell HCW 23 Manuale utente
Honeywell
Honeywell ADEMCO 5804BD Manuale utente
Honeywell
Honeywell Wireless Remote Control Manuale utente
Honeywell
Honeywell 5804BD Manuale utente
Honeywell
Honeywell NOTIFIER LCD6000A Manuale di istruzioni
Honeywell
Honeywell ADEMCO 5804BDV Manuale utente
Honeywell
Honeywell ADEMCO 5804BDV Manuale utente
Honeywell
Honeywell TCC800M Manuale utente
Honeywell
Honeywell HS3FOB1S Manuale utente
Honeywell
Honeywell 5805-6A Manuale utente
Honeywell
Honeywell Silent Knight 6860 Manuale tecnico
Honeywell
Honeywell Versa-Pro UDC3000 Manuale utente
Honeywell
Honeywell 42136 Manuale utente
Honeywell
Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Manuale utente
Honeywell
Honeywell ADEMCO 5804BDV Manuale utente
Honeywell
Honeywell REM5000R01 Manuale utente
