Honeywell HBW2PR2 Manuale utente
Document 800-22329 – Rev. A – 07/2016
HBW2PR2/HBW4PR2 WDR IR
Bullet IP Camera
Quick Installation Guide
Document 800-22329– Rev A – 07/2016
Thank you for purchasing an HBW2PR2/HBW4PR2
camera. Follow the instructions in this guide to install
and log in to your camera. For instructions on
configuring the camera, refer to the Performance Series
IP Cameras User Guide on the installation CD that came
with your camera.
If you require additional assistance, contact Tech
Support (contact info is listed on the back page).
Cautions and Warnings
WARNING To ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked “Limited Power Source” or “LPS”
on the unit, output rated to 12 VDC, minimum 0.33 A, TMA=60 deg C, or from Power
over Ethernet (PoE) provided by Listed Information Technology Equipment meeting
IEEE 802.3af PoE standard.
WARNING The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera at the same
time.
CAUTION Invisible LED radiation (850 nm). Avoid exposure to beam.
Regulatory Statements
Information to the User: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Note Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Important Safeguards
•Read and keep these instructions.
•Do not aim the camera toward a bright light source for extended periods to prevent
damage to the imager. Avoid operating the unit under or close to unstable light
sources (may cause flickering), or close to fluorescent lamps or objects reflecting
light.
•Do not touch the camera lens.
•Do not drop the camera or subject it to physical shock.
•Do not use a strong or abrasive detergent when cleaning the camera.
•Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments,
where the operating temperature is outside the recommended range of -4°F to
140°F (–20°C to 60°C).
Note Do not apply power to the camera before completing installation.
Note Ensure that the installation surface can support at least three times the weight of
the camera.
CAUTION
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
© 2016 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all
respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication
may be issued to incorporate such changes.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are
missing or damaged, contact your dealer immediately.
•Camera
•Installation CD
•Quick installation guide
•Allen key (L-wrench)
•Self-tapping screws (×4)
•Plastic wall anchors (×4)
•Mounting template
Required tools
•Phillips screwdriver
•Drill with appropriate bit for pre-drilling wall anchor holes
CAUTION Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain your warranty.
Preparing the Mounting Surface
1. Inspect the site where you want to install the camera. The mounting surface must be
flat and capable of supporting at least three times the weight of the camera.
2. Remove the backing from the mounting template sticker and affix the sticker to the
mounting surface.
Note If you are using the side exit for the cable, note the orientation of the cable
exit notch. In outdoor installations the notch should point downwards to prevent
water from entering the camera housing.
3. Drill three screw holes at the locations indicated on the mounting template sticker
and insert the three supplied plastic anchors in the holes.
4. If you want to store the cables inside the wall or ceiling, drill a hole at the cable exit
position on the mounting template and then pull the cables through the hole.
Mounting the Camera
1. If local storage is needed, insert a microSD card into the microSD card slot according
to the following steps:
a. Use a Phillips screwdriver (not supplied) and remove
the control panel cover on the outside of the camera.
b. Insert the microSD card into the microSD card slot as
shown in the picture to the right.
c. Replace the control panel cover.
2. Connect the camera with the Ethernet cable and the power cable.
a. Connect one end of the Ethernet cable to the RJ-45 port on the camera.
b. If the other end of the Ethernet cable is NOT connected to a PoE (Power-over-
Ethernet) switch or NVR, connect the power connector of the camera to a 12 VDC
power source.
3. Attach the camera assembly to the mounting surface using the supplied screws.
Aiming the Camera
1. Use the supplied Allen key to loosen the adjusting
screws on the bracket arm.
2. Set the camera to the desired position.
3. Tighten the adjustment screws.
Adjusting the Zoom and Focus
If the camera is connected to the PoE port of a Honeywell Embedded NVR, you can log on
to the camera directly from the NVR.
To log on to the camera from a PC:
1. Install the Honeywell Config Tool from the installation CD.
2. Use the Config Tool to discover the camera and open the camera’s webpage.
3. Log on to the camera as the admin user. The default user name is admin (case-
sensitive) and the default password is 1234.
Note Only Internet Explorer 11 and Firefox 46.0.1 (or later) browsers are supported.
4. Go to Setup CameraConditionsZoom and Focus. The following panel
appears:
•Click Zoom in + or Zoom out - to zoom in or out.
•Click Near - or Far + to focus near or far, or click Auto Focus to enable auto
focus.
Honeywell
www.honeywell.com/security
+1 800 323 4576
(North America only)
www.honeywell.com/security/uk
+1 44 (0) 1928 754 028
(Europe only)
www.asia.security.honeywell.com
+86 21 221 96888
(Asia Pacific only)
Document 800-22329 – Rev A – 07/2016
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Honeywell Telecamera di sicurezza
Honeywell
Honeywell HD4D3S Manuale utente
Honeywell
Honeywell HD3USX Manuale utente
Honeywell
Honeywell Performance H4D3PRV2 Manuale utente
Honeywell
Honeywell HD273H Manuale utente
Honeywell
Honeywell HD73 Series Manuale utente
Honeywell
Honeywell HC60W34R2 Manuale utente
Honeywell
Honeywell HD70PX Manuale utente
Honeywell
Honeywell HD4D3H Manuale utente
Honeywell
Honeywell HD4D3 Manuale utente
Honeywell
Honeywell HD3C Manuale utente
Honeywell
Honeywell VISTA VBC-800PI Manuale utente
Honeywell
Honeywell HDZ20HD Manuale utente
Honeywell
Honeywell HB73 Series Manuale utente
Honeywell
Honeywell HSD-361P Manuale utente
Honeywell
Honeywell HEGS5300 Manuale utente
Honeywell
Honeywell HDZ Series Manuale utente
Honeywell
Honeywell NEXPTZ4520HD-NET Manuale utente
Honeywell
Honeywell HCC334L Manuale utente
Honeywell
Honeywell HD31H(X) Manuale utente
Honeywell
Honeywell Orbiter Platinum Manuale utente
