Honeywell 5869 Manuale utente

The 5869 Hold-Up Switch/Transmitter is a finger-operated

RF transmitting device. It is typically mounted under a

counter or money draw for inconspicuous operation.

When the transmitter is activated, it emits an RF signal to

the receiver. The security system control panel sends a

burglary alarm to the central station when a RF signal is

received from an enrolled Hold-Up Switch/Transmitter.

Once activated, the 5869 Hold-Up Switch/Transmitter can

only be reset by the reset key. The 5869 also incorporates

tamper switches that are activated when the cover is

removed, or if the unit is forcibly removed from its

installation location.

• No wires to run

• Front and back tamper resistant

• Easily mounted

• Quick enrollment

• Includes battery

FEATURES

5869

HOLD-UP SWITCH/TRANSMITTER

Physical

• 1-15/16" W x 5-15/16" H x 1 3/16"D

(50mm x 150mm x 30mm)

Frequency

• 345 MHz

Battery

• 3V Lithium ADEMCO 466

or equivalent

Agency Listings

• UL listed for Household Burg UL

1023,Hold-up Burg UL 636 and

CUL 634

• For certified UL commercial

installations, use with 5881ENHC

tamper-protected wireless receiver

Compatibility

• Fully compatible with all

VISTA Control Panels

SPECIFICATIONS

HOLDUP

TRANSMITTER

DEVICE

MOUNTING

HOLE

COVER

SCREW

MOUNTING

HOLE

COVER

ATTACH

HOLE

TRIGGER

INSIDE VIEW

WITH

CIRCUIT BOARD

RESET

KEY

COVER TAMPER

RELEASE SWITCH

LITHIUM

BATTERY

MOUNTING

HOLE

MOUNTING

HOLE

5869-001-V0

COVER

SCREW

COVER

ATTACH

HOLE

BREAKAWAY

TAMPER

RELEASE TAB

SCREW

HOLE

Figure 1

ORDERING

5869 Hold-Up Switch/Transmitter

5869

HOLD-UP SWITCH/TRANSMITTER

Mount the 5869 under a counter or

money drawer for easy access by the

cashier. Refer to the steps and figures

that follow for typical mounting

instructions. Before mounting the 5869

permanently, perform Go/No Go tests

to verify adequate transmitter signal

strength at desired mounting location

(refer to the Security System Control

Panel Installation and Setup Guide).

1. Remove the two screws (Figure 1)

securing the cover to the 5869 case.

NOTE: The holes located in the opposite corner

to the screws that secure the cover to the case,

provide a means for securing the transmitter to

the counter or drawer.

2. Using the case as a drill

template, position the case

in the desired location.

3. Drill a 1/16"pilot hole at the

breakaway tamper release

hole and the two case mounting

holes (Figure 2).

4. Attach the case to the counter or

money drawer using one No. 6 x 3/4

screw (supplied) at the breakaway

tamper release.

5. Install the battery (see BATTERY

INSTALLATION/REPLACEMENT).

6. Secure the cover to the case with

the two screws removed in step 1.

7. Secure the assembled case to

the counter or drawer using the

two No. 6 x 2 mounting screws

supplied (Figure 2).

INSTALLATION

The 5869 Hold-Up Switch/Transmitter

should be programmed as a 24-hour

silent zone type. Refer to the Security

System Control Panel Installation and

Setup Guide for programming

instructions.

• During programming of the control

panel, the 5869 Hold-Up

Switch/Transmitter should be treated

as “RF” (i.e., supervised RF) Type

• The 5869 is one closed input loop

zone (loop 1)

Battery Installation/Replacement

1. Remove and retain screws securing

the 5869 cover.

2. Observing correct polarity, insert the

battery into the battery holder.

NOTE: Use care not to bend the antenna while

attempting to install battery.

3. Re-install screws to secure cover

and/or assembly. Refer to Figure 1.

PROGRAMMING

5869-002-V0

MOUNTING

HOLE

TRIGGER

HOLE

TRIGGER

BREAKAWAY

TAMPER

RELEASE

RESET

KEY

COVER

TAMPER

RELEASE

SWITCH

MOUNTING

HOLE

COVER

SCREW (2)

No. 6X1/2

COVER

LITHIUM

BATTERY

CIRCUIT

BOARD

COVER

ATTACH HOLE

COVER

ATTACH

HOLE

MOUNTING

SCREW (2)

No. 6X2

BREAKAWAY

TAMPER

RELEASE

SCREW HOLE

INDEX

TAB

COVER

SCREW

NOTE

CIRCUIT BOARD REMOVED

FOR CLARITY ONLY. DO NOT

REMOVE CIRCUIT BOARD

DURING INSTALLATION.

Figure 2

Altri manuali Honeywell Interruttore

Honeywell

Honeywell 272630D Manuale utente

Honeywell

Honeywell ZW4008 Manuale utente

Honeywell

Honeywell DG-T Series Manuale utente

Honeywell

Honeywell Micro Switch 91SE Series Manuale utente

Honeywell

Honeywell ZW4005 Manuale utente

Honeywell

Honeywell IDENT-KEY 3 Manuale utente

Honeywell

Honeywell C645A-E Manuale operativo

Honeywell

Honeywell C437D Manuale utente

Honeywell

Honeywell PLS750C Manuale utente

Honeywell

Honeywell HBT083P Manuale utente

Honeywell

Honeywell ZW4103 Manuale utente

Honeywell

Honeywell Fema DWAM Series Manuale utente

Honeywell

Honeywell krom schroder DL K Series Manuale utente

Honeywell

Honeywell IP-AK2 Manuale dell'operatore

Honeywell

Honeywell RTS-CSA Manuale utente

Honeywell

Honeywell CSP-C Manuale utente

Honeywell

Honeywell 10260A Series Manuale utente

Honeywell

Honeywell HDLS Series Manuale di servizio

Honeywell

Honeywell 10260 Series Manuale utente

Honeywell

Honeywell 39346 Manuale utente

Honeywell

Honeywell krom schroder 03250831 Manuale utente

Honeywell

Honeywell Galaxy 2 Series Manuale utente

Honeywell

Honeywell CS Series Manuale utente

Honeywell

Honeywell MICRO SWITCH BX2 Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente