HP 355 Manuale utente
HP 355/365 Cloud-Managed
Access Point Wall Mount Kit
Installation Guide
HP 355/365 AP Wall Mount Kit | Installation Guide 3
Package contents
lMounting bracket
l2 Ethernet cable adapters
lT8 Torx security screw
lPaper template for screw holes
This mounting kit supports multiple AP models. Your AP might look different
than the AP shown in this document.
Installation
Complete the following steps to install your access point using the HP 355/365 AP Wall
Mount Kit.
HP 355/365 Cloud-Managed Access Point Wall Mount Kit (JL019A)
Installation Guide
4 HP 355/365 AP Wall Mount Kit | Installation Guide
Ethernet cable routing options
There are three options for routing the Ethernet cable, depending on the placement of
your AP in relation to the source of the Ethernet cable.
Installing an Ethernet cable from below the AP
1. Route the Ethernet cable through the channel in the rear of the mounting bracket.
See Figure 1.
2. Loop the Ethernet cable over the top of the mounting bracket, and direct the cable
through the opening that leads to the AP Ethernet ports.
3. If required, route the power cable through the bottom right of the mounting bracket.
4. Install the mounting bracket as described in Installing the mounting bracket on page 7.
Figure 1: Installing an Ethernet cable from below the AP
Installing an Ethernet cable from behind the AP
1. Route the Ethernet cable through the large opening in the center of the mounting
bracket. See Figure 2.
2. If required, route the power cable through the bottom right of the mounting bracket.
3. Install the mounting bracket as described in Installing the mounting bracket on page 7.
HP 355/365 AP Wall Mount Kit | Installation Guide 5
6 HP 355/365 AP Wall Mount Kit | Installation Guide
Figure 2: Installing an Ethernet cable from behind the AP
Using the Ethernet cable adapter
1. Attach the Ethernet cable adapter(s) to the mounting bracket as shown in Figure 3.
The adapter is secured when it clicks into place.
2. If required, route the power cable through the bottom right of the mounting bracket.
3. Install the mounting bracket as described in Installing the mounting bracket on page 7.
Figure 3: Using the Ethernet cable adapter
Installing the mounting bracket
1. Hold the paper template included with this mount kit against the wall where you want
to install the mounting bracket, and mark the location of the screw holes.
2. Install wall anchors if necessary. Wall anchors are not included in this kit.
3. Align the screw holes in the mounting bracket with the previously installed anchors or
marked screw points. See Figure 4. Ensure that no Ethernet cables are obstructing
the screw holes.
HP 355/365 AP Wall Mount Kit | Installation Guide 7
8 HP 355/365 AP Wall Mount Kit | Installation Guide
Figure 4: Attaching the mounting bracket to a wall
4. Use screws to secure the mounting bracket. Screws are not included in this kit.
5. Attach any necessary cables to the AP.
6. If using the Ethernet cable adapter, connect the Ethernet cable through the opening
on the side of the mounting bracket.
To disconnect the Ethernet cable from the adapter after the installation is
complete, you must remove the AP from the bracket to access the RJ45
locking tab.
7. Push the metal slider located on the bottom of the mounting bracket up to allow the AP
to connect.
8. While still pushing the metal slider, align the mounting posts on the bracket with the
mounting holes on the AP. See Figure 5.
Figure 5: Attaching the AP to the mounting bracket
9. Install the T8 Torx security screw into the screw hole on the bottom of the mounting
bracket to complete the installation.
HP 355/365 AP Wall Mount Kit | Installation Guide 9
10 HP 355/365 AP Wall Mount Kit | Installation Guide
Figure 6: Completed installation
© Copyright 2014 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are
set forth in the express warranty statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions
contained herein.
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali HP Rack e supporto
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manuale utente
HP
HP Rack System/E Manuale utente
HP
HP LaserJet Enterprise 600 Manuale utente
HP
HP System/E41 Manuale utente
HP
HP 6400/8400 Manuale utente
HP
HP DESKJET 350 Manuale utente
HP
HP Model 745 - VME Workstation Manuale utente
HP
HP D7171A - NetServer - LPr Manuale utente
HP
HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Manuale utente
HP
HP HP 10000 G2 Series Manuale utente
HP
HP Proliant DL580 Manuale utente
HP
HP A4838A Manuale utente
HP
HP Tc4100 - Server - 256 MB RAM Manuale utente
HP
HP 11000 G2 series Manuale utente
HP
HP ProCurve 6600-48G-4XG Manuale utente
HP
HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Manuale utente
HP
HP AT-BT10 Manuale utente
HP
HP Quick Release EM870AA Istruzioni utente
HP
HP StorageWorks SSL1016 Manuale utente
HP
HP D7171A - NetServer - LPr Manuale utente
