HP StorageWorks EML E Series Manuale utente

Removal

StorageWorks

EML E-Series

Drive Module

Installation

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure that you

are properly grounded when touching

static sensitive components.

Note: This part is not hot-pluggable. It is

necessary to power down the library to

replace this part.

Note: An animation of the removal process

can be found on the documentation CD

shipped with the tape library.

Open the back

doors of the library.

Removal

StorageWorks

EML E-Series

Dre

Caution: Parts can bedamagedby

electrostatic discharge. Keep parts in their

containers until needed. Ensure that you

are properly grounded whentouching

static sensitive components.

Note: Thispart is hot-pluggable. It isnot

necessary to power downthelibrary to add

this part, however, the librarydoes have to be

power-cycled when adding or rep lacing a drive.

Note: Anew drive willnot be recognized

bythe library until aftera reboot.

Open theback door

of thelibrary.

StorageWorks

ESL

E-series

Interface

Manager

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartisnothot-pluggable.

Itisnecessarytopowerdownthelibrary

toreplacethispart.

10026

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

Powerdownthelibrary.

a.Placethelibraryoff-linebypressingthe

Standbybuttononthelibrary'sfrontpanel.

Thelibraryroboticscompletesanycurrent

commandsandthenstops.

b.Verifythatthefrontpaneldisplayindicates

“SystemOff-line”.

c.Verifythatthepickerisempty.Ifthereisa

tapecartridgeinthepicker,performaMove

commandtoplacethecartridgeinan

availableslot.[Contentneeded.]

d.Pressandholdthepowerbuttonlocatedon

thefrontofthelibrarybehindthelaptoptray

untilthefrontpanelgoesblank.

Flipthetwobreakerswitchesoffatthepower

distributionunit.

Inspect the contents of the kit. You may need a

flat-blade screwdriver to remove and replace this

tape drive.

If you are removing anexisting tape drive,

make sure tounloadanytape cartridges in

thedrive to beremoved using your application

software or thelibrary GUI touch screen. Use

your backup software to cease library activity.

Identifythe tape drive to bereplaced. The Fault

LED light may be lit, signifying a hot swap can

occur.

Inspect the contents of the kit. You may need a

flat-blade screwdriver to remove and replace this

tape drive.

If you are removing an existing tape drive,

make sure to unload any tape cartridges in

the drive to be removed using your application

software or the library GUI touch screen. Use

your backup software to cease library activity.

Identify the tape drive to be replaced. The Fault

LED light may be lit, signifying a hot swap can

occur.

Installation

Disconnect the FC cable from the drive to

be replaced by pressing down on the cable

connector tab and pulling the connector away

from the drive.

Caution: To avoid damaging FC cables,

do not pinch or sharply bend the cables

tighter than a 5 centimeter (2-inch) diameter.

Connect an FC cable to the FC connector on the

new drive. The FC cable should click into place.

Caution: To avoid damaging FC cables,

do not pinch or sharply bend the cables

tighter than a 5 centimeter (2-inch) diameter.

Connect the other end of the FC cable to its

corresponding port on the interface controller

card. Attach a label to each end of the cable to

mark the port designations. Complete this cabling

process for all drives.

If necessary, use a flat-blade screwdriver to loosen

the captive screw at the right side of the drive

module. Grasp the drive and pull the drive from

the drive bay.

To install a new drive, locate a vacant drive bay.

Remove the face plate covering the drive bay by

removing the screw holding it in place.

Remove the end cap from the FC connector on

each new tape drive to be installed. Insert the new

drive module into the vacant drive bay and tighten

the captive screw to secure the drive to the chassis.

Note: Replacing an existing tape drive

does not require power-cycling the library,

however, adding a new tape drive does

require power-cycling the library.

Verify that the FC port LED on the interface

controller card is solid green.

If necessary, upgrade the drive firmware using

the Interface Manager's Command Line Interface.

See the HP StorageWorks Interface Manager

and Command View TL User's Guide for detailed

procedures on upgrading drive firmware.

Note: A new drive will not be

recognized by the library until after a

reboot.

Getting help

• HP product information:

http://www.hp.com/products/tapestorage

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Close the back

doors of the library.

First Edition (April 2005)

Part Number: AD560-96013

*AD560-96013*

AD560-96013

Altri manuali HP Magazzinaggio

HP StorageWorks DLT80 Manuale utente

HP StorageWorks 8B - FC Entry Switch Manuale utente

HP P9000 Manuale utente

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Guida

HP C2246 Manuale del prodotto

HP LaserJet P2050 Series Manuale utente

HP Xw6600 - Workstation - 2 GB RAM Manuale utente

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP StorageWorks 9000 Virtual Libr Manuale utente

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale utente

HP StorageWorks XP1024 Guida rapida

HP StorageWorks 8000 - NAS Manuale utente

HP StorageWorks XP1024 Guida rapida

HP StorageWorks MSA 2/8 - SAN Switch Manuale utente

HP HDD Manuale utente

HP StorageWorks 8000 - NAS Manuale utente

HP StorageWorks Modular Smart Array 1500 cs Manuale utente

HP Storevirtual 4000 Manuale di istruzioni

HP StoreOnce D2D Backup System Gen2E Manuale

HP 3PAR StoreServ 7000 Manuale tecnico

HP 5243 Manuale utente

HP StorageWorks 7110 - Virtual Array Manuale utente

HP N1528A Manuale utente

HP StoreOnce 4900 Backup Manuale di istruzioni

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente

CFI

CFI TERA STOR SATA RAID IV Manuale utente