HP StorageWorks ESL E Series Manuale per l'uso e la cura

StorageWorks

ESL E-Series

Ultrium FC Drive

Replacement

StorageWork s

Caution:Parts canbedamagedby

electrostaticdischarge. Keepparts in their

containers until needed. Ensureyouare

properlygroundedwhentouchingstatic-

sensitive components.

Note:This part is hot-pluggable. It is not

necessaryto power downthelibraryto

replace this part.

Tapedrivesclusters are

numberedstartingat

thetopof the

cabinet as follows:

0,1, 2, 3, 4, 5.

In eachcluster the

drives areidentified

as follows: top

right is A, topleft

is B, bottom right

is C, bottom left is

D. Adrawing

showingthis is on

theinsideof theback

door.

Opentheback door of thelibrary.

Inspect thecontents of thekit.

StorageWorks

ESL

E-series

TapeDrive

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartishot-pluggable.Itisnot

necessarytopowerdownthelibraryto

replacethispart.

Identifythetapedrivetobereplaced.TheLEDof

thedrivewillberedoroff.

Tapedrivesclustersare

numberedstartingat

thetopofthe

cabinetasfollows:

0,1,2,3,4,5.

Ineachclusterthe

drivesareidentified

asfollows:top

rightisA,topleft

isB,bottomright

isC,bottomleftis

D.Adrawing

showingthisison

theinsideoftheback

door.

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

From the Operator Control Panel (OCP), power off

the drive to be replaced.

From Menu, select the Ops button.

Use the Up and Downbuttons to select the

drive, then press the Selectbutton.

Use the Up and Downbuttons to change the

drive to off-line, then press the Selectbutton.

Select the Backbutton to return to Menu.

Verify that the correct drive is powered down.

ESL E-Series

Ultrium 460

NFC Drive

Replacement

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure you are

properly grounded when touching static-

sensitive components.

Note: This part is hot-swappable. It is not

necessary to power down the library to

replace this part.

Drive clusters are

numbered from 0 to 5

starting at the top

of the cabinet. In

each drive cluster

the drives are

identified as

follows: top right

is A, top left is B,

bottom right is C,

bottom left is D.

A drawing of

the drive cluster is

located on the

inside of the back door.

Open the back door of the library.

Inspect the contents of the kit.

From the Home screen, select the Ops button.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to off, then press the Select button.

d. Select Yes to confirm.

e. Select the Back button to return to Menu.

f. Verify that the correct drive is powered down.

Printed in the US

Second Edition (March 2005)

Part Number: 358832-002

*358832-002*

358832-002

Getting help

• HP product information:

http://www.hp.com/products/esle

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Firmware Upgrade

If necessary, upgrade the drive firmware

using the Interface Manager's command-line

interface. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures on

upgrading drive firmware.

Close the back door of the library.

Drive Replacement

Drive Removal

Remove the FC cable from the cable clip.

1) Insert the new drive into the

vacant drive bay. 2) Tighten the captive

screw to secure the drive to the cluster.

Using a

slotted screwdriver,

1) loosen the captive screw at

the upper left corner of the drive module.

2) Move the FC cable to the side and out of the

way. Grasp the drive handle and pull the drive

from its bay.

Verify that the FC port LED on the FC interface

controller card is green.

The LED for the replaced

drive and its associated

cluster controller card LED

should be green.

14 15

Make sure that Command View TL recognizes

the replaced drive using the Command View TL

console. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures.

CAUTION: To avoid damaging FC cables,

do not sharply bend or pinch them. Allow a

radial bend when reattaching the FC cables.

Note: If needed, the tie wrap provided

with this kit can be used to help keep

the FC cables clear of the drive cluster

below by attaching the cables to the

drive handle.

Power on the drive by completing the following

steps from the OCP for the new drive.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to on-line, then press the Select button.

d. Select the Back button to return to Menu.

Use the Command View TL user interface to

reboot the interface controller card. Refer to

the HP StorageWorks Interface Manager and

Command View TL User Guide for detailed

procedures.

Connect the FC cable to the new drive. The FC

cable connector clicks into place. Insert the cable

into the cable clip on the drive.

Identify the drive to be replaced.

The LED of the drive to be replaced will be off.

CAUTION: To avoid damaging the drive,

do not remove it if the LED is still lit.

See step 2 to power off the drive.

Disconnect the Fibre Channel (FC) cable from the

drive to be replaced by 1) pressing down on the

cable connector tab and 2) pulling the connector

away from the drive.

CAUTION: To avoid damaging FC

cables, do not sharply bend or pinch them.

Drive Replacement

Drive Removal

Remove the FC cable from the cable clip.

1) Insert the new drive into the

vacant drive bay. 2) Tighten the captive

screw to secure the drive to the cluster.

Using a

slotted screwdriver,

1) loosen the captive screw at

the upper left corner of the drive module.

2) Move the FC cable to the side and out of the

way. Grasp the drive handle and pull the drive

from its bay.

Verify that the FC port LED on the FC interface

controller card is green.

The LED for the replaced

drive and its associated

cluster controller card LED

should be green.

14 15

Make sure that Command View TL recognizes

the replaced drive using the Command View TL

console. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures.

CAUTION: To avoid damaging FC cables,

do not sharply bend or pinch them. Allow a

radial bend when reattaching the FC cables.

Note: If needed, the tie wrap provided

with this kit can be used to help keep

the FC cables clear of the drive cluster

below by attaching the cables to the

drive handle.

Power on the drive by completing the following

steps from the OCP for the new drive.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to on-line, then press the Select button.

d. Select the Back button to return to Menu.

Use the Command View TL user interface to

reboot the interface controller card. Refer to

the HP StorageWorks Interface Manager and

Command View TL User Guide for detailed

procedures.

Connect the FC cable to the new drive. The FC

cable connector clicks into place. Insert the cable

into the cable clip on the drive.

Identify the drive to be replaced.

The LED of the drive to be replaced will be off.

CAUTION: To avoid damaging the drive,

do not remove it if the LED is still lit.

See step 2 to power off the drive.

Disconnect the Fibre Channel (FC) cable from the

drive to be replaced by 1) pressing down on the

cable connector tab and 2) pulling the connector

away from the drive.

CAUTION: To avoid damaging FC

cables, do not sharply bend or pinch them.

StorageWorks

ESL E-Series

Ultrium FC Drive

Replacement

StorageWork s

Caution:Parts canbedamagedby

electrostaticdischarge. Keepparts in their

containers until needed. Ensureyouare

properlygroundedwhentouchingstatic-

sensitive components.

Note:This part is hot-pluggable. It is not

necessaryto power downthelibraryto

replace this part.

Tapedrivesclusters are

numberedstartingat

thetopof the

cabinet as follows:

0,1, 2, 3, 4, 5.

In eachcluster the

drives areidentified

as follows: top

right is A, topleft

is B, bottom right

is C, bottom left is

D. Adrawing

showingthis is on

theinsideof theback

door.

Opentheback door of thelibrary.

Inspect thecontents of thekit.

StorageWorks

ESL

E-series

TapeDrive

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartishot-pluggable.Itisnot

necessarytopowerdownthelibraryto

replacethispart.

Identifythetapedrivetobereplaced.TheLEDof

thedrivewillberedoroff.

Tapedrivesclustersare

numberedstartingat

thetopofthe

cabinetasfollows:

0,1,2,3,4,5.

Ineachclusterthe

drivesareidentified

asfollows:top

rightisA,topleft

isB,bottomright

isC,bottomleftis

D.Adrawing

showingthisison

theinsideoftheback

door.

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

From the Operator Control Panel (OCP), power off

the drive to be replaced.

From Menu, select the Ops button.

Use the Up and Downbuttons to select the

drive, then press the Selectbutton.

Use the Up and Downbuttons to change the

drive to off-line, then press the Selectbutton.

Select the Backbutton to return to Menu.

Verify that the correct drive is powered down.

ESL E-Series

Ultrium 460

NFC Drive

Replacement

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure you are

properly grounded when touching static-

sensitive components.

Note: This part is hot-swappable. It is not

necessary to power down the library to

replace this part.

Drive clusters are

numbered from 0 to 5

starting at the top

of the cabinet. In

each drive cluster

the drives are

identified as

follows: top right

is A, top left is B,

bottom right is C,

bottom left is D.

A drawing of

the drive cluster is

located on the

inside of the back door.

Open the back door of the library.

Inspect the contents of the kit.

From the Home screen, select the Ops button.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to off, then press the Select button.

d. Select Yes to confirm.

e. Select the Back button to return to Menu.

f. Verify that the correct drive is powered down.

Printed in the US

Second Edition (March 2005)

Part Number: 358832-002

*358832-002*

358832-002

Getting help

• HP product information:

http://www.hp.com/products/esle

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Firmware Upgrade

If necessary, upgrade the drive firmware

using the Interface Manager's command-line

interface. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures on

upgrading drive firmware.

Close the back door of the library.

Altri manuali per StorageWorks ESL E Series

Altri manuali HP Magazzinaggio

HP 20/700 Manuale utente

HP Storevirtual 4000 Guida di riferimento rapido

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP StorageWorks XP12000 Manuale utente

HP StoreOnce B6000 Manuale utente

HP 705 Guida rapida

HP 9153A Manuale utente

HP d212 Manuale utente

HP Surestore Disk Array 12h - And FC60 Istruzioni per il montaggio

HP StorageWorks MSL6000 series Manuale utente

HP EVA P6000 Manuale utente

HP STORAGEWORKS XP24000 Manuale utente

HP SuperStore E SC10 Manuale

HP Colorado Trakker 250 Manuale di istruzioni

HP LTO-3 960 Istruzioni utente

HP StorageWorks Modular Smart Array 500 System Manuale

HP StorageWorks RDX160 Istruzioni utente

HP P-FD8GBX2-V125W-FS - v125w 8 GB USB 2.0 Flash... Manuale di riferimento

HP Surestore E Tape Library Model 2/20 Manuale utente

HP StorageWorks 4400 Manuale utente

HP C7401A - SureStore Ultrium 230 Tape Drive Manuale utente

HP Storevirtual 4000 Guida di riferimento rapido

HP Surestore Tape Library Model 2/15 Manuale utente

HP BL536A Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente

CFI

CFI TERA STOR SATA RAID IV Manuale utente