HP ProCurve 1600M Manuale utente

fantray_1up.fm Page 1 Tuesday, January 21, 2003 6:45 PM

Notes

fantray_1up.fm Page 2 Tuesday, January 21, 2003 6:45 PM

HP ProCurve Switch 4000M/8000M

Replacement Fan Tray

The HP ProCurve 4000M and 8000M switches have a replaceable fan tray. The instruc-

tions in this booklet will guide you through the process of replacing the fan tray in

your switch.

Before proceeding, make sure you read the Fan Tray Installation Precautions below.

Included Parts. The following parts should be included in your fan tray replacement

kit:

●the Replacement Fan Tray assembly (5092-0373)

●HP ProCurve Switch 4000M/8000M Replacement Fan Tray Installation

Guide (5990-3078), this guide

Tools Needed. To complete these procedures you need only a Torx T-10 screwdriver

or a flat bladed screwdriver.

Fan Tray Installation Precautions

Follow these precautions when installing your HP Switch 4000M/8000M Replace-

ment Fan Tray:

Warnings

●Make sure that all AC power is disconnected from the switch

before starting the procedures described in this guide. Do not

reconnect the power until the switch is completely reassembled

and cover plates are replaced on any open module slots or power

supply bays.

●If your switch is rack mounted, make sure that the rack is not going

to tip over as you complete these procedures. If the switch is

difficult to reach, remove it from the rack or other mounting

location before proceeding.

Cautions

●When handling the switch modules, the fan tray, and the fan tray connec-

tor, do not touch the components or edge connectors on any printed

circuit boards, or the pins on any connectors. Otherwise, damage due to

static discharge could occur.

●Refer to the installation guides that came with your switch and switch

power supply for precautions on proper handling and installation of the

switch and power supplies. For copies of the installation guides, visit the

HP Procurve web site at http://www.hp.com/go/hpprocurve.

fantray_1up.fm Page 3 Tuesday, January 21, 2003 6:45 PM

Installing the Replacement Fan Tray

Overview

The installation steps are:

1. Disconnect all AC power from the switch and remove any power supplies and

cover plates.

2. On the front of the switch, mark or otherwise note the location of the network

cables attached to the network modules in switch slots A and B so that you can

reconnect the cables to the correct ports at the end of this procedure. Then,

disconnect all network cables from modules that are installed in slots A and B

on the front of the switch.

Alternatively, if you have sufficient slack in the cables, you can leave the network

cables connected to the modules as you complete the next step.

3. Remove the Management module and any modules that you have installed in

slots A and B. (Remember which module is located in which slot).

4. Remove the old fan tray assembly.

5. Install the Replacement Fan Tray.

6. Reinstall the Management module into its slot and the network modules into

their previous positions in slots A and B. (Make sure you do not overtighten the

screws on the modules.)

7. If you disconnected the network cables in step 2, reconnect the cables to the

correct ports on the network modules.

8. On the back of the switch, reinstall the power supply or supplies and cover plates.

9. Reconnect the AC power to the power supplies.

10. Verify that the switch is operating correctly by observing the LEDs on the front

of the switch.

fantray_1up.fm Page 4 Tuesday, January 21, 2003 6:45 PM

Fan Tray Installation Steps

Follow these steps to install the replacement fan tray into the back of the Switch 4000M

or 8000M:

1. Disconnect AC power and remove power supplies and back cover plates.

2. Mark and disconnect the network cables on modules in slots A and B.

On the front of the switch, mark or otherwise note the location of the network

cables attached to the network modules in switch slots A and B so that you can

reconnect the cables to the correct ports at the end of this procedure. Then,

disconnect all network cables from modules that are installed in slots A and B

on the front of the switch.

Alternatively, if you have sufficient slack in the cables, you can leave the network

cables connected to the modules as you complete the next step.

3. Remove the Management module and any modules that you have

installed in slots A and B.

On the back of the switch, dis-

connect all AC power. Then,

loosen the 4 screws holding in

each power supply or cover

plate, and remove the power

supplies and cover plates

Loosen the two screws holding

in each module, and use the

screws to slide the modules

out. Remember which module

is located in which slot.

Caution: When handling the mod-

ules, do not touch the components

on the module boards or the edge

connectors. Otherwise, damage

due to static discharge could

occur.

fantray_1up.fm Page 5 Tuesday, January 21, 2003 6:45 PM

4. Remove the old fan tray assembly. Follow these steps:

a. Through the opening in

the front of the switch,

where the modules used

to be, reach in and discon-

nect the fan tray cable

from the switch back-

plane.

Caution: Avoid damage to

the pins on the backplane

connector by pulling the

cableconnectorstraightout.

Do not pull on the cable

itself.

b. Through the opening in the back of the switch, loosen the two screws holding

up the fan tray.

c. Pivot the fan tray away from the switch chassis and then pull it out from the

switch. (Make sure the fan tray cable is not hindered anywhere.)

Disconnect the old fan

tray cable from the

switch backplane.

Loosen the two screws.

fantray_1up.fm Page 6 Tuesday, January 21, 2003 6:45 PM

5. Install the Replacement Fan Tray. Follow these steps:

a. Insert the new fan tray into the back of the switch so that it matches the position

of the old tray. (The tabs that stick out from the sides of the switch chassis fit

into the slots in the corners of the fan tray, as shown in the illustration.)

b. Make sure the fan tray cable connector is on the front side of the switch

backplane, and then pivot the fan tray upward.

Tabs on the switch fit into

the slots in each corner

of the fan tray.

fantray_1up.fm Page 7 Tuesday, January 21, 2003 6:45 PM

b. Install and tighten the two screws that hold the fan tray in place. (Make sure

you do not overtighten the screws.).

Caution: Make sure you do not leave any loose screws or other

foreign material inside the chassis.

c. From the front of the switch, reach into the opening made by the removed

modules and connect the fan tray cable to the white 9-pin connector on the

switch mother board by pressing it straight onto the connector, all the way in

until it stops.

The cable connector aligns with the top and left side of the large management

module edge connector, as shown in the illustration.

Tighten the two screws

just until they are snug.

Align the fan tray cable connector

with the corner of the large connector

on the switch board. Then press the

cable connector straight onto the

white 9-pin connector in that location.

fantray_1up.fm Page 8 Tuesday, January 21, 2003 6:45 PM

6. Reinstall the Management module into its slot and the network

modules into their previous positions in slots A and B. (Make sure

you do not overtighten the screws on the modules.)

7. Reinstall the network cables. If you disconnected the network cables in step

2, reconnect the cables to the correct ports on the network modules.

8. Reinstall the power supplies and cover plates. On the back of the switch,

reinstall the power supply or supplies, and cover plates.

Caution: Make sure that AC power is disconnected from the power

supply before installing the power supply into the switch.

9. Reconnect the AC power to the power supplies.

Lower the power supply into

the opening and push it all the

way back until it connects with

the switch power connector.

fantray_1up.fm Page 9 Tuesday, January 21, 2003 6:45 PM

10. Verify that the switch is operating correctly by observing the LEDs on the

front of the switch, as shown in the illustration below.

The Power Status LED, the Fan Status LED, and the switch Fault LED should be

on solidly and not flashing.

The Replacement Fan Tray procedure is complete.

Power Status LEDs

switch Fault

LED

Fan Status LED

fantray_1up.fm Page 10 Tuesday, January 21, 2003 6:45 PM

Altri manuali per ProCurve 1600M

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Interruttore

HP 377707-002 Manuale utente

HP 12500 Series Manuale utente

HP StorageWorks 64 - SAN Director Switch Manuale tecnico

HP A3100-8 v2 SI Manuale di installazione

HP StorageWorks 9100 - Extreme Data Storage... Manuale utente

HP V1905-24 Manuale utente

HP FlexFabric 5930 Series Manuale utente

HP 6125XLG Manuale utente

HP J3245A Manuale dell'operatore

HP StorageWorks 1606 - Extension SAN Switch Manuale operativo e di manutenzione

HP ProCurve Switch 2650 Manuale utente

HP 263924-002 Manuale utente

HP FlexFabric 5950 Series Manuale utente

HP AdvanceStack Remote 2C Manuale utente

HP FlexFabric 12900E series Manuale di installazione

HP ProCurve 6208M-SX Manuale utente

HP zl2 Manuale utente

HP 262586-B21 - IP Console Switch 3x1x16 KVM Manuale utente

HP 1920 Gigabit Ethernet Switch Series Manuale utente

HP A7533A - Brocade 4Gb SAN Switch Base Manuale di istruzioni

HP A7990A - StorageWorks SAN Director 4/16 Blade... Manuale operativo e di manutenzione

HP M-Series Manuale utente

HP A7340A - Surestore FC 1Gb/2Gb Switch 16B Manuale utente

HP ProCurve 1810G-8 Manuale del proprietario

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente