Huawei SmartAX MA5800-X7 Manuale utente

HUAWEI TECHNOLOGIES CO., LTD.

SmartAX MA5800-X7

Quick Installation Guide

Issue: 04

Date: 2016-08-24

Intended Audience

About This Document

Change History

Symbol Conventions

This document describes how to install the MA5800-X7.

The intended audience is hardware installation engineers.

Updates between document issues are cumulative. Therefore, the latest document issue

contains all updates made in previous issues.

The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in equipment damage, data loss, performance deterioration, or

unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury,

equipment damage, and environment deterioration.

Updates in Issue 01 (2015-04-30)

This is the first release.

Updates in Issue 02 (2015-07-28)

Based on issue 01 (2015-04-30), added 4.2 Installing the service subrack in an IEC cabinet.

Updates in Issue 03 (2016-03-31)

Based on issue 02 (2015-07-28), added the requirements on third-party cabinets that accommodate

the MA5800-X7, and optimized the layout of the document.

Updates in Issue 04 (2016-08-24)

Based on issue 03 (2016-03-31), added 7.2 Cabinet with Routed Cables (AC).

Conten t

1 Precautions …………………………………..…………………………............................………….1

2 Tools and Meters………………………….………………………….............................…………….2

3 Appearance and Structure……………………………………….............................…………….3

4 Environment Requirements on Third-Party Cabinets ………………….………4

5 Space Requirements on Third-Party Cabinets ……………….………..…......5

5.1 When the Cabinet Accommodates One MA5800-X7 Subrack………….………….5

5.2 When the Cabinet Accommodates One MA5800-X7 Subrack and Another Device....6

6 Installing the Service Subrack……………….……………………...............................………...7

6.1 Installing the Service Subrack in an ETSI Cabinet............................................................7

6.2 Installing the Service Subrack in an IEC Cabinet..............................................................8

7 Routing Cables……………………………….……………………...............................………..9

7.1 Cabinet with Routed Cables (DC)...........................................................................9

7.2 Cabinet with Routed Cables (AC).........................................................................10

7.3 Routing PGND Cable and Power Cables.......................................................................11

7.4 Routing Clock Cables………….......................................................................................12

7.5 Routing Network Cable..……….……..............................................................................13

7.6 Routing Trunk Cables………...........................................................................................14

7.7 Routing Optical Fibers (P2P Board)…............................................................................15

7.8 Routing Optical Fibers (PON Board)...............................................................................16

7.9 Routing Optical Fibers (Upstream)............................................................................17

8 Post-Installation Check…………………………………………………...............................…...18

9 Power-on Check…………………………………………………………..............................….......19

1 Precautions

•After routing the cable, attach the label or fasten the tag to the cable 20 mm away from the

connector.

•After the label for the signal cable is attached to the signal cable, the rectangular text area of

the label must face rightwards or downwards.

•After the identification plate for the power cable is attached to the power cable, the text area of

the plate must face rightwards or upwards. Ensure that the side attached with the label faces

outwards.

ESD gloves ESD wrist strap

Affixing labels / tags

•This document aims to provide simple and distinctive guidelines for hardware installation.

•This document does not describe operations for the pre-delivery installation. Instead, this

document describers only the operations for on-site installation.

Electrostatic Discharge

Before touching the device, or holding the boards and IC chips, wear the ESD gloves or the

ESD wrist strap to prevent the electrostatic discharge of the human body from damaging the

sensitive components. Ensure that the other end of the ESD wrist strap is properly grounded.

•The distance between cable ties or binding straps inside the cabinet must be within 250 mm.

(For user cable, the distance must be within 200 mm.)

•Use a diagonal pliers to cut off the extra part of the cable tie to the end, and ensure that the

cable tie is neat without sharp edges to prevent hand injury.

Bundling cables

2 Tools and Meters

ESD gloves ESD wrist strap

Optical power meterMultimeter

Network cable

crimping pliers Network cable tester

Before you begin, get the following tools ready.

Marker Flat-head screwdriver Phillips screwdriver Diagonal pliers

Optical fiber

cleaner

Optical fiber

microscope

3 Appearance and Structure

The MA5800-X7 service subrack is 6 U high, and has a fan tray at the right. The subrack is

installed in the cabinet through the ETSI or IEC mounting ears.

Fan tray

Universal interface board

Service board

Power board

Grounding point

Control board

Mounting ear

Cable Manager

ESD jack

535.0

242.2 268.7

287.8

442.0

263.9

482.6

242.2 268.7

287.8

442.0

263.9

With IEC (19 inch) mounting ear With ETSI (21 inch) mounting ear

Unit: mm Unit: mm

4 Environment Requirements on Third-Party Cabinets

•Cabinet dustproof requirement: The MA5800-X7 subrack is not dustproof, so select

dustproof cabinets that support dust filter maintenance.

•Cabinet installation requirements:

For the MA5800-X7, select an IEC60297-compliant cabinet with a depth of 300 mm or more

so that a space with a depth of 55 mm or more can be reserved for cable/fiber routing after

boards are installed.

When the MA5800-X7 is installed in an ETSI-compliant cabinet that meets the related

requirements, replace the mounting ears with the ETSI-compliant mounting ears customized

by Huawei for the MA5800-X7.

•Cabinet door requirement: When devices are operating, keep the cabinet door closed.

•Grounding requirement: Huawei cabinets are grounded through mounting bars. Ensure that

third-party cabinets are properly grounded based on site conditions.

•Power distribution requirements: Ensure that an over-current protection mechanism has

been deployed on the upper-level device. A 40-A over-current protection mechanism is

recommended for the MA5800-X7. Ensure that the circuit breaker trip value of the upper-level

device is greater than or equal to the rated value on the device nameplate.

•Heat dissipation requirements:

The fan tray of the MA5800-X7 dissipates heat from the left to the right in air blowing. When

being installed on multiple open racks in parallel, do not install the device supporting air

blowing on the neighboring rack to avoid serial ventilation.

Ensure that the cabinet has an air inlet and the hole density of the cabinet door is 60% or

higher.

When a cabinet accommodates multiple subracks or the device shares a cabinet with other

active devices, ensure that the following space requirements are met.

Front view Side view

Airflow blocking object

•The MA5800-X7 supports left-in right-out heat dissipation, so the cabinet must have an

unblocked air inlet on its door.

•You are advised to reserve more than 4 U space above and under the MA5800-X7

respectively to minimize the impact on other components in the cabinet.

5 Space Requirements on Third-Party Cabinets

5.1 When the Cabinet Accommodates One MA5800-X7 Subrack

Without an air deflector With an air deflector

Front view Side view Front view Side view

10U

If the MA5800-X7 subrack is installed in a subrack with B-T airflow, you are advised to add

an air deflector to the subrack so that the hot air does not direct flow to the MA5800-X7.

When 2 U space is reserved at the air inlet and 3 U space is reserved at the air outlet, the

cabinet panels will have less impact on the heat dissipation of the MA5800-X7.

Active device

Air

deflector

(3 U)

•Reserve 10 U space between the devices or add a 3 U air deflector to redirect air flows to

minimize the mutual heat dissipation impacts on the devices.

•Reserve at least 4 U space when you route fibers or install other passive devices to facilitate

subsequent air inlet or dust filter cleaning.

5.2 When the Cabinet Accommodates One MA5800-X7 Subrack and

Another Device

5 Space Requirements on Third-Party Cabinets

6 Installing the Service Subrack

Remove IEC mounting ears

•The MA5800-X7 service subrack is configured with IEC (19-inch) mounting ears by default.

The MA5800-X7 subrack can be mounted in an IEC cabinet or rack. To install the MA5800-X7

subrack in an ETSI cabinet, uninstall the IEC mounting ears, and then install the ETSI (21-

inch) mounting ears.

•Before installing the service subrack, it is advised to install cable managers or sliding rails in

the cabinet or rack for supporting the service subrack.

Install the lower cable manager

Install the service subrack

and upper cable manager

Locate the installation

positions of the cable

manager and service subrack

on the mounting bars, and

install captive nuts at these

positions. Captive nut

Mounting bar (use a flat-

head screwdriver if no

mounting bar is available.)

Phillips screwdriver

Lower cable manager

Upper cable manager

Service subrack

Cable manager（between

mounting ear and service subrack）

Install ETSI mounting ears

6.1 Installing the Service Subrack in an ETSI Cabinet

Indice

Altri manuali Huawei Hardware di rete

Huawei

Huawei CR52-POS/STM64 Manuale utente

Huawei

Huawei OptiXstar P802E Manuale utente

Huawei

Huawei EchoLife EG8143H5 Manuale utente

Huawei

Huawei SUN2000P-375 W Manuale utente

Huawei

Huawei OptiXstar EN8245X6s-8N Manuale utente

Huawei

Huawei BTS3900 GSM Manuale utente

Huawei

Huawei CR52-10GE Manuale utente

Huawei

Huawei MatePad Paper Manuale utente

Huawei

Huawei OptiX OSN 9560 Manuale utente

Huawei

Huawei OptiX RTN PI-DC B10 Istruzioni operative e di sicurezza

Huawei

Huawei NetEngine-8000-M8 Manuale utente

Huawei

Huawei RT-FIC-1CPOS Manuale utente

Huawei

Huawei ETP4860-B1A2 Manuale utente

Huawei

Huawei eSight V200R003C00 Manuale

Huawei

Huawei SmartLi 1.0 Manuale utente

Huawei

Huawei FTK01 Manuale utente

Huawei

Huawei V600R019C00 Specifiche tecniche

Huawei

Huawei RT-FIC-1T1-V2 Manuale utente

Huawei

Huawei CR52K-4xPOS/STM16-SFP Manuale utente

Huawei

Huawei RRU3203 Manuale utente

Huawei

Huawei NIP6320 Manuale utente

Huawei

Huawei RT-1E1 Manuale utente

Huawei

Huawei CR52-MPUA Manuale utente

Huawei

Huawei EchoLife HS8245W1 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente