Huawei RRU3203 Manuale utente
HUAWEI TECHNOLOGIES CO., LTD.
RRU3203 V100R001C01
Installation Guide
Issue: 01
Date: 2010-04-13
1
Installation Tools ……………………………………
Space Requirements …………………………………
Installation Modes ……………………………………
Installation Procedure ………………………………
Components Delivered with the RRU ……………
Installing the RRU on a Metal Pole ………………..
Installing the RRU on a U-Steel ……………………
Installing the RRU on an Angle Steel ……………
Installing the RRU on Wall …………………………
Installing the RRU Cables …………………………
RRU Hardware Installation Checklist ……………
Powering On the RRU ………………………………
Appendix………………………………………………
Change History …………………………………...…
Contents
Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved.
2
3
4
6
6
7
11
11
12
14
20
20
21
26
2
Multimeter
Knife
Hammer drill (with bit 14) Vacuum cleaner
Claw hammer
ESD gloves
Heat gun
Flat-head screwdriver
(M3~M6)
Wire stripper
Wire cutter
Power cable crimping pliers Adjustable wrench
(with the diameter of at least 32 mm [1.3 in.])
Torque screwdriver
Measuring tape
Level
Marking pen
(with the diameter of no more
than 10 mm [0.4 in.])
Combination wrench
(21mm~21mm) for pole installation
(17mm~17mm) for wall installation
Phillips screwdriver
(M3~M6)
Torque wrench
Torque socket
Installation Tools
3
60 mm [2.4 in.] to 114 mm [4.5 in.]
63mm
～
80mm
63 mm [2.5 in.] to 75 mm [3 in.]
≤10°
RRU
Angle steel
or U-steel
On a metal pole On a wall
On an angle steel
On a U-steel
Installation Options
The following figure describes the specifications for the metal pole, angle steel, and U-steel where the RRU is
installed.
Metal pole Angle steel U-steel
The brackets cannot be
combined when the RRUs
are installed on the wall.
zA maximum of two RRUs can be installed on a metal pole with a diameter of 60 mm [2.4 in.] to 75 mm [3 in.] ,
and the installation mode must be standard mode. Three or more RRUs must be installed on a metal pole with
a diameter of 76 mm [3 in.] to 114 mm [4.5 in.] in a centralized way.
zIt is recommended that only one RRU be installed on a U-steel or an angle steel.
zWhen installed on a tower, one RRU can be installed only in standard mode or reverse mode rather than
side-mounted. Two RRUs cannot be installed in back-to-back mode.
The angle between
the vertical and the
angle steel or U-
steel or angle steel
where the RRU is
installed must be
less than or equal
to 10 degree.
63 mm [2.5 in.] to 75 mm [3 in.] 50 mm [2 in.] to 100 mm [3.9 in.]
30 mm [1.2 in.] to 50 mm [2.0 in.]
4
Dimensions and Installation Clearance
≥300 mm [11.8 in.]
≥500 mm [19.7 in.]
≥800mm [31.5in.]
≥600mm[23.6in.]
≥300mm[11.8in.]
a
381 mm [15.0 in.] 170 mm [6.7 in.]
485 mm [19.1 in.]
Dimensions of the RRU
bRecommended Clearance for a
Single RRU
dRecommended Clearance for
Multiple Centralized RRUs eMinimum Clearance for Multiple
Centralized RRUs
cMinimum Clearance for a Single
RRU
200 mm [7.9 in.]
300 mm [11.8 in.]
400mm[15.7in.]
100mm[3.9 in.]
600mm [23.6in.]
≥800mm[31.5in.]
≥500mm[19.7in.]
≥300 mm [11.8 in.]
≥500 mm [19.7 in.]
≥500mm[19.7in.]
300mm[11.8in.]
300mm[11.8in.]
200 mm [7.9 in.]
300 mm [11.8 in.]
600mm[23.6in.]
5
Dimensions and Installation Clearance
f g
Recommended Horizontal Spacing for
Two RRUs Installed in Parallel Minimum Horizontal Spacing for Two
RRUs Installed in Parallel
hi
Recommended Vertical Spacing for
Two RRUs Installed in Parallel Minimum Vertical Spacing for Two
RRUs Installed in Parallel
≥300 mm [11.8 in.]
≥500 mm [19.7 in.]
≥500 mm [19.7 in.]
200 mm [7.9 in.]
300 mm [11.8 in.]
300 mm [11.8 in.]
≥300 mm
[11.8 in.] ≥600 mm
[23.6 in.] ≥600 mm
[23.6 in.] 100 mm
[3.9 in.] 400 mm
[15.7 in.] 400 mm
[15.7 in.]
6
Dual-nut bolt
Main bracket
Auxiliary bracket Cover plate Attachment plate
Installation Procedure
Preparing the Installation
Main and auxiliary brackets for the RRU Front Back
Prepare the
installation
Start
Install the RRU on a
metal pole Install the RRU on a
U-steel Install the RRU on an
angle steel Install the RRU on a
wall
Install the RRU
cables
Power on the RRU
End
Checking the RRU
Hardware Installation
7
1200 mm [47.2 in.]～
1600 mm [63 in.]
40 N•m
[354 lbf•in.]
When installing the
main bracket,
ensure that the
contact piece on
the bracket is fixed.
You may fit one end of the auxiliary bracket on one dual-nut bolt assembly and then the other end on the
other dual-nut bolt assembly during the installation.
Fasten the two dual-nut bolt assemblies
alternatively. After the brackets are secure,
use a tape to measure the spacing between
the main bracket and the auxiliary bracket at
the two sides and ensure that the spacing is
the same.
zThe weight-bearing capacity of the RF
ports at the bottom of the RRU is low. Do
not place the RRU at its bottom.
zDuring the operation, place the foam
pad or cardboard under the RRU to
prevent any damage to the housing of
the RRU.
2. Use an adjustable wrench to tighten the nut until the fastening torque is 40 N·m [354
lbf•in.]. In this way, the main and auxiliary brackets are secured on the pole.
1. Install the main bracket.
Installing the RRU on a Metal Pole
aInstalling a Single RRU on a Metal Pole
3. Install the RRU on the main bracket. When you hear click sound, you can infer that
the RRU is in position.
8
Cabling cavity
In standard mode In reverse mode
Installing the RRU on a Metal Pole
Installing Two RRUs Back-To-Back on a Metal Pole
b
4. Install the second RRU on the main bracket.
3. Reinstall the attachment plate and cover plate on the second RRU by interchanging
their positions.
1. Install an RRU. For details, see page 7
Installing a Single RRU on a Metal Pole.2. Install the main fixture for another RRU.
Ensure that the cabling
cavities of the two RRUs
face the same direction
when installing the RRUs.
M6X16
4.8 N•m
[42.5 lbf•in.]
9
Installing the RRU on a Metal Pole
Installing Multiple RRUs in Centralized Mode
c
2. Relocate the attachment plate.
1. Install the main fixture and the auxiliary fixture. For details, see page 7
Installing a Single RRU in Ordinary Mode.
4. Install the second main fixture.3. Fit the tabs on the attachment plate of the
RRU into the anchor slots on the main fixture.
5. Fit the tabs on the attachment plate of
the second RRU into the anchor slots on
the second main fixture.
6. Install the third RRU.
M6X16
4.8 N•m
[42.5 lbf•in.]
Altri manuali per RRU3203
1
Indice
Altri manuali Huawei Hardware di rete
Huawei
Huawei NE-HIC-2xFE Manuale utente
Huawei
Huawei RT-NE20E-RPU-512M Manuale utente
Huawei
Huawei EchoLife HS8245W1 Manuale utente
Huawei
Huawei F01T100 Manuale utente
Huawei
Huawei OptiXstar EG8245X6-8N Manuale utente
Huawei
Huawei RT-FIC-1CPOS Manuale utente
Huawei
Huawei TP48200A-HX09A1 Manuale utente
Huawei
Huawei MA5200F-2000 Manuale utente
Huawei
Huawei RTN510 Manuale utente
Huawei
Huawei RTN XMC ODU V200 Manuale utente
Huawei
Huawei RT-FIC-4SAE Manuale utente
Huawei
Huawei RRU Manuale utente
Huawei
Huawei EchoLife EG8247W5-8T Manuale utente
Huawei
Huawei EG8010H Manuale utente
Huawei
Huawei BBU3900 Istruzioni per l'uso e l'installazione
Huawei
Huawei OptiXstar V183 Manuale utente
Huawei
Huawei RT-1E1 Manuale utente
Huawei
Huawei FIC-1/2ADSL Manuale utente
Huawei
Huawei FusionDC1000A Specifiche tecniche
Huawei
Huawei LUNA2000-97KWH-1H1 Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
