Huawei NE05E Manuale utente
HUAWEI TECHNOLOGIES CO., LTD.
NE05E&NE08E Series
Quick Installation Guide(19inch&21inch cabinet)
Issue: 05
Date: 2020-08-31
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of
their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made
between Huawei and the customer. All or part of the products, services and features
described in this document may not be within the purchase scope or the usage scope.
Unless otherwise specified in the contract, all statements, information, and
recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute a
warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: https://www.huawei.com
Email: su[email protected]
2
Installation Flow
3
Precautions
This document provides simple and distinctive guidelines for quick hardware installation of the
NE05E&NE08E(NE05E-SR/S2/SE/SF/SG/SH/SI/SQ&NE08E-S6/S6E/S9).
Based on the height of a device, the NE05E-SR/S2/SE/SF/SG/SH/SI/SQ are considered 1 U
devices, and the NE08E-S6/S6E are considered 2 U devices, and the NE08E-S9 are considered 3
U devices. 1 U = 44.45 mm (1.75 in.)
As the installation methods are similar, the fixed NE05E-SI is used as an example for the 1 U
device, and the card-inserted NE08E-S6 is used as an example for the 2 U device. The
installation differences are specially described in this document.
This document does not describe pre-delivery assembly. This document only describes
procedures for onsite installation.
Wear ESD gloves or Antistatic Wrist Strap prior to
contact with the equipment or before handling the
plug-boards, boards, and IC chips to prevent
damage to sensitive components caused by
electrostatic discharge from the human body.
Binding intervals between cable ties or optical fiber binding straps inside the cabinet
cannot exceed 250 mm.
Electrostatic Discharge
Pre-Installation Check
Verify that the equipment room, power supply, ground cables and optical cables are ready
for installation. Start the installation according to the engineering design documents after
confirming that conditions are met. Refer to the
Installation Guide
for information about
specific operational requirements and technical specifications.
NOTE
CAUTION
CAUTION
CAUTION
Bundling cables
4
Tape Measure Philips Screwdriver
(M2-M6) Flathead Screwdriver
(M2-M6)
Adjustable Wrench
Level Bar
Ratchet Crimp
Tool Cable Cutter
Wire Stripper
Network Cable
Crimping Pliers Diagonal Pliers
Sharp-nose Pliers
Bayonet Wrench
Paper Knife
Marker Pen
Electric Iron
Heat Gun Multimeter
ESD Gloves
Binding Strap Insulation Tape
Antistatic Wrist
Strap
Punching Wire pliers
Vacuum cleaner
Tools for Installation
Cord end
terminal crimper
Cable Tester Optical Power
Meter
BER Tester
Coax Stripper
5
NE05E-S2
Introduction to the 1U-height Chassis
Clock interface
Power supply
interface
Time interface
NM interface
(Console interface)
Alarm interface
FE/GE electrical interface
10GE optical interface
FE/GE optical interface
E1 interface
Alarm interface
Power supply
interface
GE optical interface
Clock and time interface
T1 interface
Antistatic jack interface
FE/GE electrical interface SHDSL interface
NE05E-SE/NE05E-SF
10
10
10
NM interface
(Console interface)
FE/GE optical
interface
10
10
PGND point
PGND point
6
NE05E-SG/NE05E-SH/NE05E-SI/NE05E-SQ
Clock interface
Power supply interface
Time interface
NM interface
(Console interface)
Electrical interface
GE optical interface
Alarm interface
E1 interface
10
10
FE/GE optical
interface
FE/GE optical interface FE/GE electrical interface
Power supply interface Clock interface
10GE optical interface
Antistatic jack interface
Time interface
NM interface
(Console interface)
Alarm interface
For running an AC NE05E-SQ, you must turn on the switches of both AC power modules
operating in 1+1 backup mode.
NOTE
10
10
PGND point
PGND point
7
NE08E-S6
Introduction to the 2U-height Chassis
10
Alarm interface
Power supply interface
GE optical interface
Clock interface
Time interface
Antistatic jack interface
E1 interface
NM interface
(Console interface)
Electrical interface
10
NE08E-S6E
Alarm interface
Power supply interface
GE optical interface
Clock interface
Time interface
Antistatic jack interface NM interface
(Console interface)
Electrical interface
10
10
10GE optical interface
PGND point
PGND point
8
NE08E-S9(DC)
Introduction to the 3U-height Chassis
Alarm interface PGND point
Power supply interface
GE optical interface
Clock interface
Time interface
Antistatic jack interface
E1 interface
NM interface
(Console interface)
Electrical interface
NE08E-S9(AC)
Alarm interface PGND point
Power supply interface
optical interface
Clock interface
Time interface
Antistatic jack interface NM interface
(Console interface)
710
3
7
2
6
10
1
5
9
4
8
3
7
2
6
1
5
4
8
9
aInstalling the floating nut
1
Installing the Chassis
bInstalling the chassis in the cabinet
Floating nuts
When fixing the floating nuts, keep a distance of at
least 50 mm on both the left and right sides of the NE
device for proper ventilation.
Installation holes for the floating nut: The three
holes with even spacing equal a 1-U height.
A 1 U device corresponds to holes 1-3, and a 2 U
device corresponds to holes 1-6.
1
2
3
4
5
6
2.0±0.2 N·M
M6
•Install the chassis and align the installation holes of the mounting ears with the floating nuts,
and fasten the two captive screws clockwise.
•Each 2U device requires only one cable tray, which must be installed on the right of the device
(front view).
•If you deploy an NE in the same cabinet as another device, reserve a distance of 1 U or higher
between the two devices for heat dissipation.
Cable guiding
frame
Scenario I: Installing the Chassis in the 19-inch Cabinet
Mount bar
(Use a Flathead Screwdriver if
no mount bar is available)
Altri manuali per NE05E
3
Questo manuale è adatto per i seguenti modelli
12
Indice
Altri manuali Huawei Router di rete
Huawei
Huawei EchoLife HG8245 Manuale utente
Huawei
Huawei Quidway S9300 Manuale utente
Huawei
Huawei 31010GEV Manuale utente
Huawei
Huawei WiFi Q2 Pro Manuale utente
Huawei
Huawei AF23 Manuale utente
Huawei
Huawei e5180s Manuale utente
Huawei
Huawei 5G CPE Pro H112-372 Manuale utente
Huawei
Huawei AR500 Specifiche tecniche
Huawei
Huawei Quidway NetEngine80E Manuale utente
Huawei
Huawei B311-520 Manuale utente
Huawei
Huawei Pocket WiFi 4G Manuale di installazione e funzionamento
Huawei
Huawei PTN Series Manuale utente
Huawei
Huawei E173 Manuale utente
Huawei
Huawei E5373s-155 Manuale utente
Huawei
Huawei E586BS-6 Manuale utente
Huawei
Huawei AOLYNK S1505L Manuale utente
Huawei
Huawei HW-02G Manuale utente
Huawei
Huawei E5180 Manuale utente
Huawei
Huawei H122-372 Manuale utente
Huawei
Huawei DN8245V-50 Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza