Huawei UPS5000-A series Manuale utente

(1) Cover (2) Maintenance

bypass switch

(3) Control unit (4) Bypass unit

(5) Power units

(6) Monitor display unit

Issue: 02

Part Number: 31500BBU

Date: 2019-06-10

UPS5000-A-(200 kVA-300 kVA)

Quick Guide (Isolation Protection)

UPS Model Cabling Mode Capacity Weight Dimensions (H xW x D)

UPS5000-A-200K-FT Routed in and

out from the top 200 kVA,

300 kVA 380 kg 2000 mm x 600 mm x 850

mmUPS5000-A-300K-STT 470 kg

1Overview

UPS5000-A-200K-FT UPS5000-A-300K-STT

(1)

Cover

(2) Mains input switch

(3) Bypass input switch

(4) Maintenance bypass switch

(5) Output switch

(6) Control

unit

(7) Bypass

unit

(8) Power

units

(9) Monitor display unit

(10) Folder

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation and operation.

3. Only Huawei engineers or engineers certified by Huawei are allowed to install, commission,

and maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the

resulting UPS faults are beyond the warranty scope of Huawei.

4. This document describes how to install a single UPS. For details about how to install parallel

systems, contact Huawei technical support.

2Installing the UPS

Secured Installation

1. Determine the position for installing the

cabinet. Mark mounting holes based on

the drawings. (unit: mm)

2. Use a hammer drill to drill four holes for installing

expansion bolts and then install four expansion

bolts in the holes. Remove the bolt, spring washer,

and flat washer.

3. Slide the cabinet on its castors to the installation

position.

4. (Optional) If the castors of the UPS need to be

lifted from the ground, perform Step 1 to Step 2 in

Non-Secured Installation.

5. Remove the rear panel of the cabinet, and then

open the front door.

6. Remove the four plugs from the bottom of the

cabinet (two on the front and two at the back).

7. Insert four M12x115 expansion bolts into the

expansion bolt holes in the floor, and tighten

the expansion bolts.

2. Check whether the bottom of the cabinet is

horizontal by using a level. If the cabinet is not

leveled, adjust the leveling feet.

1. Lower the four leveling feet at the bottom of the

cabinet by using a wrench until all the four

castors at the bottom hang in the air and the

leveling feet bear the whole cabinet weight.

3Connecting Cables

Non-Secured Installation

UPS Cable Connection Reference

3.1

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets and

surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

The cabling route is for reference only. Connect cables based on site requirements.

NOTE

1. Ensure the maintenance bypass switch is OFF.

Open the front door, remove the front cover,

and remove covers from the top of the cabinet

based on the site requirements.

Connecting Cables to the UPS5000-A-200K-FT

3.2 2. (Skip this step if the mains input and bypass

input share a power source.) Remove the

copper bars between the mains input and

bypass input.

3. Connect the ground cable, input cable

(There is no need to connect the bypass

input power cable if the mains input and

bypass input share a power source.), and

signal cable.

Signal

cable

Port

Description Bolt

Specifications Torque

Mains input M10 x 40 26N•m

Bypass input M10 x 40 26N•m

Battery input M12 x 60 46N•m

Output M10 x 40 26N•m

PE M10 x 30 26N•m

4. Connect the battery cable and output cable.

NOTE

The wire routed from the middle point of positive and negative battery strings is the neutral wire.

Take a battery string consisting of 40 batteries for example. The battery neutral wire is routed

from the middle between positive and negative battery strings, each consisting of 20 batteries.

1. Ensure the maintenance bypass switch is OFF.

Open the front door, remove the front cover,

and remove covers from the top of the cabinet

based on the site requirements.

2. (Skip this step if the mains input and bypass

input share a power source.) Remove the

copper bars between the mains input and

bypass input.

Connecting Cables to the UPS5000-A-300K-STT

3.3

Signal cable

3. Connect the ground cable, power cable, and signal cable. There is no need to connect the

bypass input power cable if the mains input and bypass input share a power source.

NOTE

The wire routed from the middle point of positive

and negative battery strings is the neutral wire.

Take a battery string consisting of 40 batteries for

example. The battery neutral wire is routed from

the middle between positive and negative battery

strings, each consisting of 20 batteries.

Port

Description Bolt

Specifications Torque

Mains input M12 x 45 46N•m

Bypass input M12 x 45 46N•m

Battery input M12 x 45 46N•m

Output M12 x 45 46N•m

PE M12 x 30 46N•m

Paper protective

film

Sealing putty

Dustproof cover

(1) Rear of units (2) Cabinet top (3) Wiring terminal blocks (4) Switches

2. After verifying the installation, reinstall all the

covers.

3. (Remove the paper protective film from the

sealing putty.) After routing cables and verifying

cable connections, seal the gap between

cables and the cabinet using sealing putty.

4. Do not remove the dustproof cover before

power-on to prevent dust inside the UPS.

4Verifying the Installation

1. Check that there is no foreign matter in the cabinet.

Sealing putty must

be used as a whole

and the gap can be

sealed only from the

top.

UPS5000-A-200K-FT UPS5000-A-300K-STT

5Powering On and Starting the UPS

1. Before powering on the UPS, ensure that the UPS has passed all check items in the UPS5000

Commissioning and Acceptance Report and Chapter 4.

2. Measure the voltage and frequency of the UPS upstream input switch. The line voltage range is

138–485 V AC, and the frequency range is 40–70 Hz.

Powering On the UPS

5.1

Starting the Inverter

5.2

Initial Startup

a) If this is the initial startup, set the language, time, date, network parameters, and system

parameters on the Settings Wizard screen.

System User LCD Preset Password WebUI Preset Password

admin (system administrator)

000001 Changeme

operator (common user) 000001 Changeme

Close the upstream bypass and mains input switches.

(Full configuration model) Close the UPS bypass input switch, output switch, and mains input switch.

After the UPS is powered on, initialization begins. The MDU displays the Huawei logo and an

initialization progress bar.

b) After you set parameters on the Settings Wizard screen, the MDU displays the Bypass mode

and No battery alarms, which do not need to be handled. If there is any other alarm, you need

to rectify the fault.

c) View the system running status diagram on the MDU to check that the UPS is working in

bypass mode.

d) Start the inverter on the app.

NOTE

•The Service Expert app can be downloaded from Google Play and can run on Android.

•The port number is 443 by default and can be modified. If the UPS is managed using the app,

the port number must be set to 443.

Download the mobile phone app (Service Expert).

On the app home screen, tap StartUp to

access the Set Startup screen. Set the Site

and Device Type as required, and connect

the device. Enter the UPS IP and Port as well

as the user name and password of the WebUI

account, and tap Login.

Enable the mobile phone WLAN, search for

the UPS WiFi signal, and connect to the WiFi

signal. The default value of SSID is UPS_WIFI.

Insert the WiFi module into the USB port on

the MDU. Set System Info > Settings >

Comm Settings > WiFi Settings on the MDU.

The initial WiFi password is Changeme by

default.

After login, tap Power-on password

activation on the screen. A message is

displayed, indicating whether to start the UPS.

Tap OK.

Enter Bar code and Verification code

obtained from the MDU on the Offline

Activation screen. Tap Generate PWD to

generate a startup password.

On the MDU, choose System Info >

Maintenance > Inv. ON and obtain the Bar

code and Verification.

Enter the generated password in the

password textbox on the MDU to start the

inverter.

Use the app to

start the inverter

online?

Yes

No, start the

inverter

offline

Open the Service Expert app on the mobile

phone.

Open the Service Expert app on the mobile

phone.

On the home screen of the app, tap StartUp

to access the Set Startup screen. Set Site

and Device Type as required, and tap

Offline Activation.

Non-initial Startup

a. Choose Common Functions from the main menu and tap Inv. ON.

b. In the displayed login window, enter the user name and password, and tap .

c. In the displayed dialog box, tap OK to start the inverter.

Powering On Loads

5.3

1. After the inverter starts, the UPS works in normal mode. The Bypass mode alarm disappears

from the MDU.

2. After confirming that the battery strings are properly connected, turn on the battery string input

circuit breaker. If there are multiple battery strings, turn on the circuit breaker for each battery

string and then turn on the general circuit breaker between battery strings and the UPS. The No

battery alarm disappears from the MDU.

3. Turn on the UPS downstream output switch to supply power to the loads.

6Shutting Down the UPS

After you shut down the inverter, the UPS transfers to bypass mode if the bypass is normal; the

UPS supplies no power if the bypass is abnormal. Before shutting down the UPS, ensure that all

loads have been shut down.

Powering Off a Single UPS

6.2

Shutting Down the Inverter to Transfer the UPS to Bypass Mode

6.1

(Optional) Setting Parameters for the BCB Box

5.4

1. On the main menu of the LCD, choose Common Functions and tap Inv. OFF.

2. In the displayed login window, enter the user name and password, and tap .

3. In the displayed dialog box, tap Yes to shut down the inverter.

1. If a BCB box is configured, set MUE05A connection to Enable in Settings > Dry contacts Set,

and then set BCB connection [OL] and Battery breaker [STA] to Enable.

Open the downstream output switch and battery string switch.

(Full configuration model) Open the UPS mains input switch, bypass input

switch, and output switch.

Open the upstream mains input and bypass input switches.

Altri manuali per UPS5000-A series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Huawei UPS

Huawei

Huawei UPS5000-S-1600KVA-FP Manuale utente

Huawei

Huawei UPSJZ-T Series Manuale utente

Huawei

Huawei UPS5000-A series Manuale utente

Huawei

Huawei UPS5000-S-300 kVA Manuale utente

Huawei

Huawei UPS5000-A-H Series Manuale utente

Huawei

Huawei UPS5000 Manuale utente

Huawei

Huawei UPS2000-G1-6 kVA Manuale utente

Huawei

Huawei UPS5000-E-25K-SM Manuale utente

Huawei

Huawei PDU8000 Series Manuale utente

Huawei

Huawei UPS5000-E-****-FM series Manuale utente

Huawei

Huawei UPS5000-H-1200 kVA Manuale utente

Huawei

Huawei UPS5000-A-500 kVA Manuale utente

Huawei

Huawei UPS2000-G-6KRTLL Manuale utente

Huawei

Huawei SmartLi-512V-162Ah-F Manuale utente

Huawei

Huawei UPS5000-S-600 Manuale utente

Huawei

Huawei UPS5000-E-30K-FM Manuale utente

Huawei

Huawei UPS5000-E-****-FM series Manuale utente

Huawei

Huawei UPS2000-H Manuale utente

Huawei

Huawei UPS5000-E Series Manuale utente

Huawei

Huawei UPS5000-E-50K-HABBS Manuale utente

Huawei

Huawei UPS2000-A-1 kVA Manuale utente

Huawei

Huawei UPS5000-E-80K-LABBS Manuale utente

Huawei

Huawei UPS5000-A-400K-SL Manuale utente

Huawei

Huawei UPS5000-A-600K-SC Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente