Huawei UPS5000-E-50K-HABBS Manuale utente
1
Issue: 01
Part Number: 31500DXL
Date: 2020-04-13
UPS5000-E-(60 kVA–125 kVA)
Quick Guide (Integrated UPS 3.0)
1Overview Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
UPS Model Capacity
Configuration
Weight (Full
Configuration) Dimensions (H x W x D)
UPS5000-E-50K-HABBS 30 kVA, 60 kVA 352 kg
2000 mm x 600 mm x
1100 mm
UPS5000-E-50K-HASBS 390 kg
UPS5000-E-125K-HABBS-01 90kVA, 120kVA,
125kVA
435 kg
UPS5000-E-125K-HASBS-01 453 kg
•The appearance of the UPS5000-E-60K-HABBS (02312TVW, 02312TWB) is similar to that of
the UPS5000-E-125K-HABBS-01 (02312TVY, 02312TWC).
•The appearance of the UPS5000-E-60K-HASBS (02312TVX) is similar to that of the UPS5000-
E-125K-HASBS-01 (02312TWA).
•If Requisite modules is set to 5, the maximum output capability of each module is 25 kVA/25 kW.
1. Before installation, read the user manual carefully to get familiar with product information and
safety precautions.
2. Use insulated tools during installation.
3. Only engineers certified by Huawei or its agents are allowed to install, commission, and
maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the UPS
faults caused are beyond the warranty scope of Huawei.
2
UPS5000-E-125K-HASBS-01
(1) Power input
status indicator
(2) ATS
(3) Lighting
circuit breaker
(4) ATS handle
installation slot
(5) Power distribution
circuit breaker for the
mart cooling product
(6) IT load circuit
breaker
(7) UPS input
circuit breaker
(8) UPS maintenance
bypass circuit breaker
(9) Control
module
(10) Bypass module
(11) Power module
(12) Monitor display unit
(MDU)
(13) Power distribution
monitoring board
(14) UPS output
circuit breaker
UPS5000-E-60K-HABBS
(1) Power input
status indicator
(2) Input circuit
breaker
(3) Lighting
circuit breaker
(4) Power distribution
circuit breaker for the
mart cooling product
(5) IT load circuit
breaker
(6) UPS input
circuit breaker
(7) UPS maintenance
bypass circuit breaker
(8) Control module
(9) Bypass module
(10) Filler panel
(11) Power module
(12) Monitor display unit
(MDU)
(13) Power distribution
monitoring board
(14) UPS output
circuit breaker
3
2Installing the UPS
1. Determine the mounting holes based on the marking-off template, drill holes, and install expansion
sleeves (unit: mm).
3. Secure the UPS.2. Adjust the anchor bolts and ensure that the
anchor bolts touch the floor. Then level the
UPS.
4
2. Secure the tail frame upper sealing plate to
the tail frame.
3(Optional) Installing the Tail Frame
1. Secure the tail frame fittings to the tail frame.
There are two upper sealing plates, and the
one used in this step has a gap.
3. Remove the rear door of the cabinet, hinges,
connecting plates, and ground cable. 4. Adjust the tail frame anchor bolts until the tail
frame is as high as the cabinet. Then secure
the tail frame to the UPS.
5. Install the hinges, connecting plates, and rear door on the tail frame.
6. Connect the ground cable to the rear door of the cabinet.
4(Optional) Combining Cabinets
The figures are for reference only. The actual product appearance prevails.
5
2. Remove the cabinet connecting kits from
the rack.
3. Secure the connecting kits in the
connection positions on the front door
using screws.
1. Open the front and rear doors. Wrench the
anchor bolts using an wrench to adjust the
cabinet height. Use a level to level the cabinet.
4. Use the same method to secure the
connecting kits in the connection
positions on the rear door.
5Connecting Cables
5. Repeat the procedure to combine other cabinets.
6. Secure the bolts using a socket wrench.
•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may
ignite and cause personal injury or device damage.
•After cables have been installed, clean the cabinet in a timely manner. Ensure that there is no
foreign matter inside and around the cabinet.
•You need to prepare terminals onsite. The stripped length of the copper wire should be the
same as that of the part of the terminal that covers the conductor.
Remove the screw from the supporting kit
of the connecting kit to secure the
connecting kit.
UPS Cable Connection Reference
5.1
6
Connecting Power Cables
3.2
Scenario 1: Routing Cables from the Top
The cabling route is for reference only. Connect cables based on site requirements.
1. Remove the insulation protective panel from
the rear of the cabinet and remove covers
from the top as required.
2. Connect a ground cable to the UPS cabinet.
ATS input
3. Connect the AC input power cable.
MCCB input
7
4. Connect battery cables, AC output power cables, fire protection cables and generator Start/Stop
cables. Neutral cables
Battery cables PE cables
IT and smart cooling product output power
cables
Lighting cables
Fire Protection and Generator
Start/Stop Cables (ATS input cabinet)
Port Description Bolt Specifications Bolt Length Torque
AC input M12 45 mm 46 N·m
Battery input M10 30 mm 26 N·m
PE M12 45 mm 46 N·m
Safe grounding M6 16 mm 4.5 N·m
Route a neutral wire from the middle of the
positive and negative battery strings.
Take a battery string consisting of 40 batteries
as an example. A neutral wire is routed from the
middle of positive and negative battery strings,
each consisting of 20 batteries.
8
•Cables can be routed in and out from the bottom only when a tail frame is configured for the
cabinet.
•This section uses the ATS cabinet as an example. For details about cable connections in other
cabinets, see the procedure in this section.
•Connect the inside cables first, and then the outside cables.
1. Remove the cover plate from the cable hole
at the bottom of the tail frame.
2. Remove the insulation panels at the rear of
the cabinet.
3. Connect a ground cable to the safety ground
of the UPS cabinet.
4. Connect AC input power cables.
Scenario 2: Routing Cables from the Bottom
9
5. Connect the battery cable and ground cable
of the cabinet. 6. Connect AC output power cables.
Connecting Communications Cables
5.2
The following figure uses cable routing from the top as an example.
Lighting wiring
terminal
Smart cooling
product wiring
terminal
IT wiring terminal
Connect a communications cable between the FE port on the UPS monitoring interface card and
any PoE port on the ETH gateway.
Connecting CommunicationsCables to Northbound Devices
10
ETH gateway
6Verifying the Installation
1. Check that there is no foreign matter at the top and bottom of the cabinet, copper bars, switches,
and the rear of modules.
(Optional) ConnectingSmartLi
Communications Cables
Connect one end of the cable to the COM1
port on the UPS monitoring interface card, and
connect the other end to the COM port on the
SmartLi monitoring interface unit.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Huawei UPS
Huawei
Huawei UPS2000-G-3 kVA Manuale utente
Huawei
Huawei UPS5000-A-30 kVA Manuale utente
Huawei
Huawei UPS2000-H Manuale utente
Huawei
Huawei UPS5000-S-300 kVA Manuale utente
Huawei
Huawei UPS5000-E Series Manuale utente
Huawei
Huawei UPS5000-E-BF Series Manuale utente
Huawei
Huawei UPS2000-A Series Manuale utente
Huawei
Huawei PDC-0038V4ACIOA-V2 Manuale utente
Huawei
Huawei UPS5000-H-1200K-NT Manuale utente
Huawei
Huawei UPS5000-H-600 kVA Manuale utente
Huawei
Huawei UPS2000-G-2KRTL Manuale utente
Huawei
Huawei UPS5000-H Series Manuale utente
Huawei
Huawei UPS5000-E-200K-SM Manuale utente
Huawei
Huawei UPS2000-G1-6 kVA Manuale utente
Huawei
Huawei UPS5000-S-1200 kVA Manuale utente
Huawei
Huawei UPS2000-G-3KRTLL Manuale utente
Huawei
Huawei UPS2000-G-6KRTLL Manuale utente
Huawei
Huawei UPS5000-E Series Manuale utente
Huawei
Huawei PDU8000 Series Manuale utente
Huawei
Huawei UPS5000-E Series Manuale utente
Manuali UPS popolari di altre marche
Pylontech
Pylontech Victron & Pylontech US5000 Manuale utente
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuale utente
Mecer
Mecer ME-1000-WTU Manuale utente
Mustek
Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento
Emerson
Emerson Liebert NXL series Manuale utente
MAKELSAN
MAKELSAN BOXER SERIES Manuale utente
