Human Touch ht103 Manuale utente
REMOVING THE BACKREST
1. Locate the connector box on the bottom right-hand side of the chair (Fig.2).
2. Using a Phillips-head screwdriver, remove the two screws that secure the connector box cover, remove the cover, then disconnect the connectors.
3. Using a nail clippers, or other suitable instrument, cut and remove all zip ties that secure the backrest connectors and cable harness to the bottom of the
chair, being careful not to cut the harness casing.
1. Remove the head pillow and backrest pad, following the instructions in the Use & Care manual.
2. Push down on the backrest release lever, then fold the backrest forward onto the chair seat (Fig.1).
3. Power off the chair and unplug it.
GET READY
(Fig.1)
1
Backrest release lever
Tools Required: Pliers, vice grip, Phillips-head screwdriver, small hammer, nail clipper or other instrument suitable for cutting zip ties, new zip ties
NOTE: SAVE ALL REMOVED PARTS FOR USE DURING REASSEMBLY
REPLACING THE BACKREST
Connector box
(Right-hand side of the chair)
(Fig.2)
Sept 19, 2011
HT-100/102/103/120/130/140
410/430/450/3100/3200/3300
It is imperative that Human Touch® products are repaired in a manner that ensures product safety and regulatory compliance and that is fully consistent with the practices used
during the manufacturing process. Therefore, Human Touch requires that all product repairs are performed using only factory-new parts and in accordance with these repair
instructions. Failure to adhere to these instructions voids the product warranty and releases Human Touch from all liability for injury or product damage resulting from the repair.
SERVICE LEVEL: 3
4. Pull gently outward on the bottom of one of the rear side panel covers to remove it (Fig.3).
5. Using a Phillips-head screwdriver, remove the screw and washers that secure the metal hinge pin to the chair (Fig.4).
6. Using a pliers (or a vice grip if necessary), pull the hinge pin toward you until it is freed from the chair (Fig.5). NOTE: The hinge pin is lubricated.
Place it on a disposable object, such as a paper towel, to avoid damaging the flooring beneath the chair.
NOTE: When the hinge pin is removed, the two spacers that are located between the backrest and the chair base will most likely fall off (Fig.6).
Be sure to set these spacers aside for use during reassembly.
7. Repeat steps 4 - 6 on the other rear side panel panel.
8. Carefully lift the backrest up and off the chair base.
Hinge pin
(Fig.5)
Backrest
spacers
(Fig.6)
2
(Fig.3)
Hinge pin
Washer
Screw
(Fig.4)
INSTALLING THE NEW BACKREST
1. Place the new backrest into position, face-down on the chair base.
2. From the outside of one of the side panels, insert the hinge pin through the hole, just until it is visible on the inside of the side panel.
3. Place the two spacers into position on the inside of the side panel, with the smaller spacer between the larger spacer and the side panel, then push the
hinge pin through both spacers (Fig.7).
4. Use your fingers to line up the bracket in the side of the backrest and the hinge pin; you will need to pull up slightly on the lower part of the backrest to
properly align the hinge pin with the bracket.
5. Insert the hinge pin as far into the bracket as possible, then use a small hammer to install it completely into the bracket.
6. Secure the hinge pin to the side panel using a Phillips-head screwdriver and the screw you removed earlier.
7. Replace the side panel cover, by aligning the plugs on the inside of the cover with the corresponding holes on the chair, then pushing the cover firmly
into place (Fig.8).
Hinge pin
Side panel
Smaller spacer
Larger spacer
Backrest
(Fig.7)
(Fig.8)
3
8. Repeat steps 2 - 7 on the other side panel.
9. Reconnect the cables at the connector box on the bottom right-hand side of the chair (Fig.9).
10. Using a Phillips-head screwdriver, secure the connector box cover using the two screws you removed earlier.
11. Replace the zip ties you removed previously, to secure the connector boxes and cables to the bottom of the chair.
12. Reinstall the chair pads, following the instructions in the Use and Care Guide.
13. Plug in and power on the chair, then verify that both the massage and recline functions work.
4
Please send any questions or comments regarding these instructions to: [email protected]
© 2011 Human Touch®, LLC.
Connector box
(Right-hand side of the chair)
(Fig.9)
Altri manuali per ht103
1
Questo manuale è adatto per i seguenti modelli
11
Indice
Altri manuali Human Touch Massaggiatore
Human Touch
Human Touch HT-100 Manuale utente
Human Touch
Human Touch HT-2620 Manuale utente
Human Touch
Human Touch AcuTouch 6.0 Manuale utente
Human Touch
Human Touch Cirqlation HT-1360 Manuale utente
Human Touch
Human Touch PC6 Manuale utente
Human Touch
Human Touch CIRQLATION HT-1341 Manuale utente
Human Touch
Human Touch HT-1470 Manuale utente
Human Touch
Human Touch HT-1000 Manuale utente
Human Touch
Human Touch ht 135 Manuale utente
Human Touch
Human Touch HT-5270 Manuale utente
Human Touch
Human Touch CirQlation Pro Manuale utente
Human Touch
Human Touch acuTouch 9500 Manuale utente
Human Touch
Human Touch h t1280 Manuale utente
Human Touch
Human Touch Immersion Seating WholeBody 2.0 Manuale utente
Human Touch
Human Touch feel better HT-245PS Manuale utente
Human Touch
Human Touch PC-095 Manuale utente
Human Touch
Human Touch NOVO Manuale utente
Human Touch
Human Touch ht 7450 Manuale utente
Human Touch
Human Touch HT 7120 Manuale utente
Human Touch
Human Touch pc 075 Manuale utente
