Hunter Hydrawise Pro-HC Manuale utente

Table of Contents

PRO-HC - Connecting Sensors or Flow Meters (Optional)

Wiring for standard Hydrawise 0.75" (20 mm) or 1" (25 mm) flow meters is as follows:

Wiring for open/closed contact sensors is as follows:

PRO-HC - Mounting Controller

INSTALLING THE PRO-HC CONTROLLER

MOUNTING THE CONTROLLER TO A WALL

PRO-HC - Connecting AC Power

Indoor Cabinet:

Outdoor Cabinet:

PRO-HC - Connecting Solenoid Valves

PRO-HC - Connecting Sensors or

Flow Meters (Optional)

Pro-HC Controller supports most open/closed contact type of sensors such as Hunter rain

and soil moisture sensors.

Connect one sensor wire to COMMON on the controller.

Connect the Normally Closed or Normally Open wire from the sensor to SEN-1 or SEN-2

on the controller and configure in the Hydrawise app.

For full details, refer to the instructions provided with your sensor, or flow meter.

Once you've wired your sensor you must configure it in your Hydrawise account.

Wiring for standard Hydrawise 0.75" (20 mm) or 1" (25

mm) flow meters is as follows:

FLOW METER WIRE LABEL ON CONTROLLER

Blue SEN-1, SEN-2

White SEN COM

Red Not connected

Wiring for open/closed contact sensors is as follows:

SENSOR WIRE LABEL ON CONTROLLER

Normally Open/Normally Closed wire SEN-1, SEN-2

Second (common) wire SEN COM

See Configuring Sensors [1] for full instructions on setting up sensors.

PRO-HC - Mounting Controller

INSTALLING THE PRO-HC CONTROLLER

Start by choosing a location with good Wi-Fi coverage. Wi-Fi coverage can be easily tested

using a smartphone. A high signal strength is recommended. Wi-Fi connectivity can also

be tested on the Pro-HC itself (signal strength is shown when you select a wireless

network).

MOUNTING THE CONTROLLER TO A WALL

All necessary hardware is included for most installations.

1. Use the hole at the top of the controller as a reference and secure a 1" (25 mm) screw

into the wall. Note: Install screw anchors when attaching the controller to drywall or

masonry wall.

2. Align controller with the screw and slide the keyhole on top of the controller over the

screw.

3. Secure controller in place by installing screws in the other mounting holes.

STEPS 1-3

PRO-HC - Connecting AC Power

Indoor Cabinet:

1. Route transformer cable through the hole on the bottom left side of the controller

2. Connect one Yellow Wire to each of the screws marked 24AC and the Green Wire to

GND.

STEPS 1-4

Note: The indoor Pro-HC is not water or weather resistant and must be installed indoors or

in a protected area. This device is not intended for use by young children. Never let

children play with this device.

Outdoor Cabinet:

The outdoor model is water and weather resistant. Connecting the outdoor Pro-HC to the

primary power should be done by a licensed electrician following all local codes.

1. Route AC power cable and conduit through the 1/2" (13 mm ) conduit opening on the

left side of the bottom of the cabinet.

2. Connect the wires to the transformer wire located inside the junction box. International

units are supplied with a built-in terminal strip. Always use a UL listed conduit 1/2" (13

mm ) male adapter when installing the AC wiring.

3. Insert the adapter into the 1/2" (13 mm ) hole at the bottom of the controller. Attach a

nut to the adapter inside the enclosure.

4. A battery is not required for this controller. Watering will not occur without AC power.

Since this controller has non-volatile memory, the program, clock and calendar will be

retained during a power outage.

STEPS 1-4

Note: To be performed by a licensed electrician only. Always use UL listed ½" (13 mm)

conduit with male adapter when installing AC wiring. Pro-HC controllers are intended to be

supplied AC power with an over-current protected device. Improper installation could result

in shock or fire hazard. This device is not intended for use by young children. Never let

children play with this device.

PRO-HC - Connecting Solenoid

Valves

1. Route valve wires between control valve location and controller.

2. At the valve location, attach a common wire to either solenoid wire of all valves. The

most commonly used color for the common wire is white. Attach a separate control wire

to the remaining wire of each valve. All wire splice connections should be done using

waterproof connectors.

3. Route valve wires through the conduit and attach conduit to one of the openings on the

bottom of the cabinet.

4. Strip 1/2" (13 mm) of insulation from ends of all wires. Secure the valve common wire

to "COM" (Common) terminal. Attach all individual valve control wires to the appropriate

station terminals.

PRO-HC CONTROLLER

All wire connections should be done using waterproof connectors. Connect each of the

other individual wires to a different colored wire. Record zones against wire color for later

reference. Connect the common wire from the multicore cable (usually white) to the

terminals on the controller marked COM.

Altri manuali per Hydrawise Pro-HC

Indice

Altri manuali Hunter Controllori

Hunter

Hunter Hydrawise HC-1200M Manuale utente

Hunter

Hunter HCC Manuale di installazione

Hunter

Hunter i-core IC-600PL Manuale utente

Hunter

Hunter XC Istruzioni operative

Hunter

Hunter SRC Plus Manuale utente

Hunter

Hunter Pro-C Manuale utente

Hunter

Hunter 99373 Manuale utente

Hunter

Hunter 27178 Manuale utente

Hunter

Hunter WVC Istruzioni operative

Hunter

Hunter Hydrawise HC-1200M Manuale utente

Hunter

Hunter SRC Plus Manuale di installazione e funzionamento

Hunter

Hunter SVC Manuale utente

Hunter

Hunter SRC Plus Manuale utente

Hunter

Hunter 99111 Manuale utente

Hunter

Hunter VSX Manuale utente

Hunter

Hunter ICC2 Manuale utente

Hunter

Hunter PRO-C P2C Series Istruzioni operative

Hunter

Hunter IC600SS Manuale utente

Hunter

Hunter Node Manuale utente

Hunter

Hunter XC Hybrid Istruzioni operative

Hunter

Hunter ACC Manuale utente

Hunter

Hunter NODE-100 Istruzioni operative

Hunter

Hunter Smart Valve Controller Istruzioni operative

Hunter

Hunter X-CORE Istruzioni operative

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente