Hunter Hydrawise Pro-HC Manuale utente

PRO-HC IRRIGATION CONTROLLER

Hydrawise™Ready

Quick Start Guide

hunterindustries.com

TABLE OF CONTENTS

PRO-HC SUPPORT

Thank you for purchasing the Hunter Pro-HC Controller. This Quick Start Guide will help

you install and congure the Pro-HC Controller and connect to Wi-Fi. For support of the

Hydrawise™ cloud soware or help with your Hydrawise account, please visit

hunter.direct/prohchelp.

Your Pro-HC box contains:

• A Pro-HC Wi-Fi controller

• 24 VAC transformer (indoor model) or built-in transformer (outdoor model)

• Three screws and three wall anchors for wall mounting

• Three wire nuts for U.S. outdoor and one Terminal block for European outdoor models

Installation 3

Connecting AC Power 5

Connecting Station Wires 7

Connecting Sensors or Flow Meters 8

Connecting to a Wi-Fi Network 9

App Conguration 10

ESFRITPTTR DE EN

INSTALLATION

Installing the Pro-HC Controller

Start by choosing a location with good Wi-Fi coverage. Wi-Fi coverage can be easily

tested using a smartphone. A signal strength of two or three bars is recommended.

Wi-Fi connectivity can also be tested on the Pro-HC itself (signal strength is shown

when you select a wireless network).

Mounting the controller to a wall

All necessary hardware is included for most installations.

Mounting the controller to a wall (continued)

1. Use the hole at the top of the controller as a reference and secure a 1" (25 mm) screw

into the wall. Note: Install screw anchors when attaching the controller to drywall or

masonry wall.

2. Align controller with the screw and slide the keyhole on top of the controller over

the screw.

3. Secure controller in place by installing screws in the other mounting holes.

For PHC-601-A, PHC1201-A, and PHC2401-A: If the supply cord is damaged,

it must be replaced by the manufacturer or service agent or a similarly qualied person

to avoid hazard.

FR ES EN

CONNECTING AC POWER

Indoor cabinet

Route transformer cable through the hole on the bottom le side of the controller and

connect one yellow wire to each of the screws marked 24AC and the green wire to GND.

Note: The indoor Pro-HC is not water or weather resistant, and must be installed

indoors or in a protected area. This device is not intended for use by young children.

Never let children play with this device.

Transformer

ESFRITPTTR DE EN

Outdoor cabinet

The outdoor model is water and weather resistant. Connecting the outdoor Pro-HC to the

primary power should be done by a licensed electrician following all local codes.

HOT

(Black)

NEUTRAL

(White)

GROUND

(Green)

1. Route AC power cable and conduit

through the ½" (13 mm) conduit opening

on the le side of the bottom of the

cabinet.

2. Connect the wires to the transformer

wires located inside the junction box.

International units are supplied with a

built-in terminal strip. Always use a UL

listed conduit ½" (13 mm) male adapter

when installing the AC wiring.

3. Insert the adapter into the ½" (13 mm)

hole at the bottom of the controller.

Attach a nut to the adapter inside the

enclosure.

4. A battery is not required for this controller.

Watering will not occur without AC power.

Since this controller has non-volatile

memory, the program, clock, and calendar

will be retained during a power outage.

Note: To be performed by a licensed electrician only. Always use UL listed ½" (13 mm)

conduit with male adapter when installing AC wiring. Pro-HC controllers are

intended to be supplied AC power with an over-current protected device. Improper

installation could result in shock or re hazard. This device is not intended for use by

young children. Never let children play with this device.

ESFRITPTTR DE EN

CONNECTING STATION WIRES

1. Route valve wires between control valve

location and controller.

2. At valves, attach a common wire to

either solenoid wire of all valves. This is

most commonly a white-colored wire.

Attach a separate control wire to the

remaining wire of each valve. All wire

splice connections should be done using

waterproof connectors.

3. Route valve wires through the conduit

and attach conduit to one of the

openings on the bottom of the cabinet.

4. Strip ½" (13 mm) of insulation from ends

of all wires. Secure the valve common

wire to “COM” (Common) terminal.

Attach all individual valve control wires

to the appropriate station terminals.

Note: All wire connections should be done using waterproof connectors. Connect

each of the other individual wires to a dierent colored wire. Record zones against

wire color for later reference. Connect the common wire from the multicore cable

(usually white) to the terminals on the controller marked COM.

CONNECTING SENSORS OR FLOW METERS (OPTIONAL)

Pro-HC Controller supports most open/closed contact type of sensors, such as Hunter

rain and soil moisture sensors.

1. Connect one sensor wire to COMMON on the controller.

2. Connect the Normally Closed or Normally Open wire from the sensor to SEN-1 or

SEN-2 on the controller and congure in the Hydrawise app.

For full details, refer to the instructions

provided with your sensor, or ow meter.

Once you've wired your sensor, you must

congure it in your Hydrawise account.

See Conguring Sensors at

hydrawise.com/support for full

instructions on setting up sensors.

Wiring for standard Hydrawise 0.75" (20 mm) or

1" (25 mm) ow meters is as follows:

Flow Meter Wire Label on Controller

Blue SEN-1, SEN-2

White SEN COM

Red Not connected

Wiring for open/closed contact sensors is as follows:

Sensor Wire Label on Controller

Normally Open /

Normally Closed wire SEN-1, SEN-2

Second (common) wire SEN COM

ESFRITPTTR DE EN

CONNECTING TO A WI-FI NETWORK

When your controller is rst powered on, it will run a short wizard to connect it to your

wireless router.

If you’re not using the initial startup wizard, then go to the Wireless Settings section to

make changes. For support, please contact hunter.direct/prohchelp.

Using the wizard

1. Select your wireless network from the list shown on the controller display

and press the Conrm button on screen.

2. Enter your wireless password and press the OK button on keyboard.

When connecting to your wireless network, the Wi-Fi icon at the bottom right of the

controller screen will ash. Connecting takes about 30 seconds and when successfully

connected the Wi-Fi icon will stop ashing and stay on.

Note: If your network is not listed, check if the unit is

within wireless range.

Note: Make sure you press the OK button aer you’ve

entered your password. Pressing the Home or Back

buttons will not save your changes.

HYDRAWISE APP CONFIGURATION

To connect the Pro-HC Controller to the Hydrawise app, follow these steps and then

follow the on-screen instructions.

1. If you have not already done so, go to hydrawise.com and register for an account.

2. If this is your rst time logging in, you will be guided through a setup wizard to help

you with initial conguration of your controller.

The owner’s manual and app instructions are located here: hydrawise.com/support

hunter.direct/prohchelp

TROUBLESHOOTING

Need more helpful information on your product?

Find tips on installation, controller programming,and more.

Altri manuali per Hydrawise Pro-HC

Indice

Lingue:

Altri manuali Hunter Controllori

Hunter

Hunter X2-400 Istruzioni operative

Hunter

Hunter Pro-C Manuale utente

Hunter

Hunter Hydrawise HPC Manuale utente

Hunter

Hunter Hydrawise HC-1200M Manuale utente

Hunter

Hunter Hydrawise HCC-FPUP Manuale utente

Hunter

Hunter WVC Istruzioni operative

Hunter

Hunter X-CORE XC-2 Manuale utente

Hunter

Hunter SpectraProbe XE Istruzioni per l’uso

Hunter

Hunter Hydrawise Pro-HC Manuale utente

Hunter

Hunter Hydrawise HC-1200M Manuale utente

Hunter

Hunter EC Manuale utente

Hunter

Hunter Pro-C PCM-1600 Manuale utente

Hunter

Hunter Eco-Logic 6 Istruzioni operative

Hunter

Hunter X-CORE XC-2 Manuale elenco delle parti

Hunter

Hunter 27206 Manuale utente

Hunter

Hunter ACC2 Manuale di installazione

Hunter

Hunter Hydrawise HC-1200M Manuale utente

Hunter

Hunter X-CORE Istruzioni operative

Hunter

Hunter SRC Plus Manuale utente

Hunter

Hunter 27178 Manuale utente

Hunter

Hunter WVC-100 Istruzioni originali

Hunter

Hunter Pro-HC601-A Manuale utente

Hunter

Hunter ICC-800PL Istruzioni operative

Hunter

Hunter NODE-BT Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente