Hunter PRO-C Hydrawise Manuale utente
2
3
3
6
7
8
9
11
13
15
Table of Contents
Table of Contents
HCC - Quick Start Guide
HCC - Connecting AC Power
HCC - Power Module Wiring Diagram
HCC - Valve Wiring
HCC - Installing ICM Station Modules
HCC - Wire Distance to Valves
HCC - Installing Wi-Fi Antenna Extension Kit
Can Two Zones Run Simultaneously with a HCC controller?
HCC - Configure Controller Offline
Copyright 2021 Hunter Industries. All Rights Reserved. 2
HCC - Quick Start Guide
HCC - Connecting AC Power
Connecting the controller to primary AC power should be done by a licensed electrician following all
local codes. Install in approved conduit and fittings. The controller can operate with either 120VAC
or 230VAC power. Supply wires must be 14AWG/ 2 mm2 or larger.
IMPORTANT: If you are using the plug-in method, the wiring is exactly the same but you will require
an outlet. The plug referred to as a Pigtail (three wires including neutral, hot, and ground) can be
purchased at most hardware outlets or a Hunter Authorized Dealer [1] (P/N: PIGTAIL).
Copyright 2021 Hunter Industries. All Rights Reserved. 3
REMOVE FACEPACK
1. Turn AC power off at the source, and verify that it is off.
2. Disconnect the facepack ribbon cable
3. Remove the facepack.
4. Remove the cover from the junction box.
Copyright 2021 Hunter Industries. All Rights Reserved. 4
WIRING
1. Strip about 0.5” (13 mm) of insulation from the end of each AC power wire.
2. Route the wires through the conduit opening inside the junction box.
3. Connect the incoming black power wire (HOT) with the black wire lead from the
transformer.
4. Connect the incoming white wire (NEUTRAL) with the blue lead from the
transformer.
5. Connect the incoming green wire (GROUND) with the green and yellow wire from
the transformer.
6. Cap the unused brown wire coming from the transformer. Replace the cover of
the junction box and screw it into place.
7. Replace cover, turn on the power, and test.
Copyright 2021 Hunter Industries. All Rights Reserved. 5
EARTH GROUND CONNECTION (LIGHTNING PROTECTION)
1. Insert the copper wire from earth ground hardware, and tighten the screw in front.
2. Minimum 10 AWG/5mm2 wire to earth ground hardware.
3. Add copper-clad steel ground rods and/or plates sufficient to achieve 10Ω or less resistance at a
minimum 8’/2.5 m away from the controller.
HCC - Power Module Wiring Diagram
Power Module Terminals
1. Green Ground
2. Yellow 24 VAC Transformer
3. Yellow 24 VAC Transformer
4. White Sensor Common
5. Red Rain Sensor
6. Black Flow Meter
7. C Common
8. P/MV Pump or Master Valve
9. REM Remote Control Input
10. White Sensor Common
8. Red Rain Sensor
9. Black Flow Meter
Copyright 2021 Hunter Industries. All Rights Reserved. 6
HCC - Valve Wiring
1. Route valve wires between control valve location and controller.
2. At valves, attach a common wire to either solenoid wire of all valves. The most commonly used
color for the common wire is white. Attach a separate control wire to the remaining wire of each
valve. All wire splice connections should be done using waterproof connectors.
3. Open hinged faceplate on the controller to access the terminal strip area.
4. Route valve wires through the conduit and attach conduit to the controller at the large conduit
opening on the right side of the bottom of the cabinet. The conduit opening has a triple knockout
to accommodate 1", 1¼", or 1½" (25, 32, or 40 mm) conduit. Each section can be easily
removed using a knife.
5. Strip ½" (13 mm) of insulation from ends of all wires. Secure valve common wire to C (Common)
terminal on any of the valve modules or power module. Then attach all individual valve control
wires to appropriate station terminals.
HCC CONTROLLER
Copyright 2021 Hunter Industries. All Rights Reserved. 7
HCC - Installing ICM Station Modules
The base model of HCC is supplied with an ICM-800 station output module. The capacity of the
controller is increased when new station modules are installed and recognized.
Standard ICM station modules are available in 4, 8, and 22 station sizes (ICM-400, ICM-800, ICM-
2200). These may be added at any time after initial installation.
Note: The ICM-2200 (22 Station module) must always be installed in the last two module slots to
make it compatible.
Model Max Station Count Total ICM 800 Modules Total ICM 2200 Modules
HCC-800-PL 38 Qty:2 - ICM-800 Qty:1 - ICM-2200
HCC-800-M 54 Qty:4 - ICM-800 Qty:1 - ICM-2200
HCC-800-SS 54 Qty:4 - ICM-800 Qty:1 - ICM-2200
Copyright 2021 Hunter Industries. All Rights Reserved. 8
HCC-800-PP 54 Qty:4 - ICM-800 Qty:1 - ICM-2200
STEP 1 STEP 2 STEP 3
Open the controller inner panel, and
choose the next available open slot in
the controller. Slots are numbered,
down the first column and up the
second.
Flip the blue locking lever into the
vertical unlocked position.
Tip the two tabs on one end of the
module into the mating holes in one end
of the slot, and tip the module firmly into
place.
STEP 4 STEP 5 STEP 6
Flip the locking lever into the horizontal
locked position.
Press the Reset button on the back of
the controller control panel. This is
required for the controller to recognize
the new module.
Connect field and common wiring as
needed and test.
HCC - Wire Distance to Valves
Copyright 2021 Hunter Industries. All Rights Reserved. 9
Below is a chart indicating the maximum wire run between the controller and the Hunter AC solenoid
valves.
Valve Wire Sizing (Feet)
Ground Control Wire
18 16 14 12 10 8 6
18 850 1040 1210 1350 1460 1540 1590
16 1040 1340 1650 1920 2150 2330 2440
14 1210 1650 2150 2630 3080 3450 3700
12 1350 1920 2630 3390 4170 4880 5400
10 1460 2150 3080 4170 5400 6670 7650
81540 2330 3450 4880 6670 8700 10530
61590 2440 3700 54000 7690 10530 13330
Notes:
Maximum one-way distance in feet between controller and valve heavy-duty solenoid: 24 VAC, 350
mA inrush current, 190 mA holding current, 60 Hz; 370 mA inrush current, 210 mA holding current,
50 Hz
Valve Wire Sizing (Metric)
Ground Control Wire
0.5 1 1.5 2.5 4 6
0.5 140 190 210 235 250 260
1.0 190 290 335 415 465 495
1.5 208 335 397 515 595 647
2.5 235 415 515 730 900 1030
4.0 250 465 595 900 1175 1405
6.0 260 495 647 1030 1405 1745
Notes:
Maximum one-way distance in meters between controller and valve Heavy-duty solenoid: 24 VAC,
350 mA inrush current, 190 mA holding current, 60 Hz; 370 mA inrush current, 210 mA holding
current, 50 Hz
Copyright 2021 Hunter Industries. All Rights Reserved. 10
Altri manuali per PRO-C Hydrawise
2
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Hunter Sistema di irrigazione
Hunter
Hunter Hydrawire Manuale utente
Hunter
Hunter G835 Manuale utente
Hunter
Hunter Hydrawise Ready Manuale utente
Hunter
Hunter Institutional Series Manuale utente
Hunter
Hunter Institutional Series I-90 Manuale utente
Hunter
Hunter PGJ Rotor Manuale utente
Hunter
Hunter Professional Series Guida
Hunter
Hunter ST Series Manuale utente
Hunter
Hunter Institutional Series I-25 Plus Manuale utente
Hunter
Hunter Institutional I-40 Series Manuale utente
Hunter
Hunter SRC Plus 600i Manuale utente
Hunter
Hunter Institutional Series I-35 Manuale utente
Hunter
Hunter I-31 Plus Manuale utente
Hunter
Hunter EC-401-A Istruzioni operative
Hunter
Hunter Institutional I-40 Manuale utente
Hunter
Hunter Institutional Series Manuale utente
Hunter
Hunter Institutional Series Manuale utente
Hunter
Hunter I-60 Series Manuale utente
Hunter
Hunter PGJ Manuale utente
Hunter
Hunter X-CORE Istruzioni operative
Manuali Sistema di irrigazione popolari di altre marche
Cellfast
Cellfast 52-305 Manuale utente
Tyco Fire Product
Tyco Fire Product Star Galaxy SGQR Manuale utente
Tyco Fire Product
Tyco Fire Product CENTRAL A Manuale utente
Oral Care Technologies
Oral Care Technologies Hydro Floss Manuale utente
Reliable
Reliable F1-300 Manuale utente
Tyco Fire Product
Tyco Fire Product Gem F892 Manuale utente
