Huskie Tools EP-100WC Manuale utente
Operating Instruction Manual
For EP-100WC Compression Tool
with Parts List
EP-100WC SPECIFICATIONS
SPECIFICATIONS
Output: 100 ton
Weight: 96 lbs.
Size: 7-1/2”W x 14”H
Die Style: HA100 Series
Ram Stroke: .98” travel (24.8mm)
Oil Volume: 19 cu/in (314cc)
• Designed for Full Tension Transmission and
Substation Connections
• Double Acting Hydraulic Cylinder for Quicker
Return Times
• Lightest Weight Models in their Class
• Removable Die Caps for Easy Cable Insertion
100 TON
COMPRESSION HEAD
Keep Fingers Out Of
Pinch Areas
Always Wear Safety
Glasses
Secure Latch Before
Operating. Failure to
Secure Latch can Result
in Severe Tool Damage
and Personal Injury.
Do Not Operate
Without Dies
The User Should Be
Properly Trained in the
Correct Procedures
Required For Work
Around Electrical Lines.
GENERAL INFORMATION
The following steps are guidelines for safe operation of the Huskie EP-100WC. Please take the time to review
them as these are helpful hints that have been accumulated over the years.
1. Never operate the tool without dies or without the cap in place. Ram may be extended more
than its stroke if the cap is not in place to function as a stop.
2. Make sure that the cap is in its proper position. When the cap is properly placed, trigger latches
into either one of the grooves located on top of cylinder.
3. Securely connect couplers. Ram may not be retracted if couplers are improperly engaged.
4. Never connect or disconnect couplers under hydraulic pressure.
5. Be sure to bleed air from hydraulic system after tool has been overhauled for seal replacement.
6. Fully retract ram when tool is not in use.
7. Keep die grooves of cap and ram clean.
OPERATING INSTRUCTIONS FOR EP-100WC
1. Connect hoses to pump and press. Upper port is pressure or advance, lower port is the return.
2. Select appropriate dies for the connector being used and attach one die half to die holder and the other
half to ram. Be sure dies are secured by the die retainer pins.
3. Insert conductor into connector and place it between dies for the compression. To insert a splice, press
trigger on the cap and twist 90°degree to lift off.
4. Operate pump to 10,000 psi for proper output tonnage.
5. Operate pump to retract the ram.
6. To remove connector from tool, depress trigger and twist cap 90° degrees to lift off.
7. Be sure to attach the dust caps to couplers to prevent damage to the oil ports.
MAINTENANCE
1. Avoid storage of tool in humid environment. Keep tool clean after use.
2. Wipe off dust or compound and keep die grooves and ram area clean.
3. Contact Huskie Tools Service Department at 1-800-860-6170 for any service problems. Daily maintenance
will ensure good performance.
MODEL EP-100WC DIAGRAM
MODEL EP-100WC PARTS LIST
MODEL EP-100WC WARRANTY
All Huskie REC-Series battery driven products carry a 5 year warranty, and the ECO-Series carry a 3
year warranty. The BP-70E, BP-70EI, and the BP-70MH batteries carry a 5 year warranty from the date
stamped on the battery. The LED indicator on the BP-70-EI battery carries a 1 year warranty from
purchase date. Hydraulic hammers carry a one year warranty and all other Huskie products carry a 5
year warranty. Huskie reserves the right to determine all warranty claims. Failure due to misuse, abuse
or repairs attempted by anyone other than Huskie Tools, Inc., or an authorized service center render
this warranty null and void. Our patented drop-out bypass cartridge can be re-calibrated or tested at
no charge for the life of the tool. All factory repaired or reconditioned hydraulic tools carry a one year
warranty on parts and labor.
REPAIR AND WARRANTY CLAIMS
All claims must be sent to Huskie for inspection and authorization. A Return Goods Authorization
is required before shipping tools to Huskie. Secure the authorization by calling 1-800-860-6170 or
writing to Huskie’s main office with details of claim. Non-warranty repairs are handled using the same
procedure. Repairs exceeding 50% of the cost of a new tool will be advised before repairs are made.
PLEASE RETAIN FOR YOUR RECORDS
Purchaser’s Name: ___________________________________________________________
Address: ___________________________________________________________
City, State, Zip: ___________________________________________________________
Tool Model Number: ___________________________________________________________
Serial Number: ___________________________________________________________
Date Purchased: ___________________________________________________________
Purchased From: ___________________________________________________________
MODEL EP-100WC WARRANTY
HOW TO GET SERVICE UNDER THE TERMS OF THE LIMITED WARRANTY
Return your product directly to Huskie Tools, Inc. as our representative network is not prepared
to service the product under the terms of this warranty.
1. Write, call or fax Huskie stating the tool’s purchase date and problem. You will be given a RGA #
to assure that your merchandise will be properly handled upon its receipt. OR, go online to
www.huskietools.com and click on “Repairs”.
2. CAUTION: Make sure the product is packaged adequately so as to prevent damage or loss during
transit. The shipment must be prepaid and we recommend that it be insured. A cover letter
indicating the reason for the return should be included in order to facilitate repairs.
SEND THIS PORTION WITH ANY TOOL WHEN REQUESTING REPAIRS,
WARRANTY OR RECONDITIONING WORK
Please call or Fax Huskie for an RGA#
Customer Job No. _______________________
Address________________________________
City___________________________________ State _____ Zip _____
Tool Model ____________________________
Warranty Claim _____ Repair Only ____
Customer Name:____________________
Phone ( _____ ) ________________________
City___________________________________ State _____ Zip _____
Serial No. _________________________
Estimate Required: Yes _____ No _____
198 N. Brandon Drive
Glendale Heights, Illinois 60139
(630) 893-7755 • Fax (800) 345-3767
Toll Free 1-800-860-6170
http://www.huskietools.com
Indice
Altri manuali Huskie Tools Utensili elettrici
Huskie Tools
Huskie Tools EP-750HA Manuale utente
Huskie Tools
Huskie Tools ECO-EZO Manuale di istruzioni
Huskie Tools
Huskie Tools REC-6NDSL Manuale utente
Huskie Tools
Huskie Tools SL-BND Manuale utente
Huskie Tools
Huskie Tools 7M Series Manuale utente
Huskie Tools
Huskie Tools HH1500 Manuale utente
Huskie Tools
Huskie Tools REC-5750 Manuale di istruzioni
Huskie Tools
Huskie Tools REC-6510 Manuale utente
Huskie Tools
Huskie Tools SL-610 Manuale utente
Huskie Tools
Huskie Tools REC-BCN658 Manuale utente
Huskie Tools
Huskie Tools REC-6430 Manuale utente
Huskie Tools
Huskie Tools SL- C510 Manuale utente
Huskie Tools
Huskie Tools S-40B Manuale di istruzioni
Huskie Tools
Huskie Tools IL-ND Manuale utente
Huskie Tools
Huskie Tools REC-B658U Manuale utente
Huskie Tools
Huskie Tools REC-658U Manuale di istruzioni
Huskie Tools
Huskie Tools REC-585YC Manuale di istruzioni
Huskie Tools
Huskie Tools SL-750 Manuale utente
Huskie Tools
Huskie Tools SL-510 Manuale utente
Huskie Tools
Huskie Tools REC-6510K Manuale utente
