Hyco K18 Manuale utente

K18 Smart Badge Scanner

User Manual

www.hycoiot.com

K18 Smart Badge Scanner User Manual

Disclaimer

Please read through the manual carefully before using the product and operate it

according to the manual. It is advised that you should keep this manual for future

reference.

Do not disassemble the device or remove the seal label from the device. Otherwise,

Shanghai Hyco Genyong Technology Co., Ltd. does not assume responsibility for the

warranty or replacement.

All pictures in this manual are for reference only and actual product may differ.

Regarding to the product modification and update, Shanghai Hyco Genyong

Technology Co., Ltd. reserves the right to make changes to any software or product

to improve reliability, function, or design at any time without notice. Besides, the

information contained herein is subject to change without prior notice.

The products depicted in this manual may include software copyrighted by Shanghai

Hyco Genyong Technology Co., Ltd. or a third party. The user, corporation or

individual, shall not duplicate, in whole or in part, distribute, modify, decompile,

disassemble, decode, reverse engineer, rent, transfer or sublicense such software

without prior written consent from the copyright holders.

This manual is copyrighted. No part of this publication may be reproduced or used in

any form without written permission from Hyco.

Please visit www.hycoiot.com or check the latest version of the specification sheet

for the latest product information

K18 Smart Badge Scanner User Manual

1. Design

K18 Smart Badge Scanner User Manual

Rays: Direct rays

Wearing: Hanging around the neck with a lanyard, or wearing on the pocket

with a buckle.

Thermometry: Click the button on the left side of the scanner.

Scanning: Click the button on the right side of the scanner.

2. Charging

Fast charging K18 Smart Badge Scanner according to the following picture and

texts.

Confirm two ends of the USB cable. Connect the small end with the

USB interface of Badge Scanner and connect the other end with a power

adapter;

Plug the connected adapter into the mains socket;

The indicator light of Badge Scanner turns red and keeps on, and the

battery icon on the screen turns to USB cable icon, which indicates

charging status of the scanner;

The battery icon on the screen turns to USB cable icon, and the

indicator light of Badge Scanner turns green and keeps on, which

indicates that the charging is completed.

★Do not look at the scanning window during charging process or the red

light from the scanner will hurt eyes directly.

K18 Smart Badge Scanner User Manual

3. Wearing

·Wearing Method (1): Put the buckle of a removable lanyard through the lanyard

hole of Badge Scanner, and press the buckle so that the buckle is locked and the

scanner can be worn around the neck.

Wearing Method (1)

·Wearing Method (2): Take off the lanyard in the method (1) and wear Badge

Scanner on the outside of the chest pocket with the sheet metal.

Wearing Method (2)

K18 Smart Badge Scanner User Manual

4. Instruction

4.1 Install the program and start Bluetooth connection.

4.2 Collect information

Scan ID/Passport

K18 Smart Badge Scanner User Manual

4.3 Temperature measuring

5. Packing List

Name

Qty

Usage

x 1

Scanning bar/QR code and collecting

information

Smart Badge Scanner

x 1

Charging Smart Badge Scanner

Power Adapter

x 1

Connecting with power adapter to charge

or connecting with other devices

数据线

x 1

Instructions of the product

Manual

K18 Smart Badge Scanner User Manual

x 1

Product Quality Certification

Certifiation

x 1

For wearing Smart Badge Scanner

Removable Lanyard

For computer usage (this part needs to

be purchased separately)

Bluetooth Receiver

6. Specifications

Model

K18

Weight

70g±2g (without lanyard)

Dimensions (W*D*H)

111.3mm*70.3mm*8.6mm

Scanner

HYCO CMOS-Sensor Scanner

Resolution

1280x800 pixcels

Code Reading

Barcodes/2D codes

Scanning Distance

Long, general or macro type

Lanyard

1 piece

LED Indicator

RGB LED (programmable)

USB

USB2.0

Vibration Indicator

Supported

Buzzer

Supported

Bluetooth

BT4.2 BLE

K18 Smart Badge Scanner User Manual

Battery

[email protected]

Charging Time

2.5 hours

Battery Life

8 hours (when fully charged with 15-20cm depth of

field and vibration on, and scanning once every5

seconds)

Scanning Keys

Mechanical keys

IP Level

IP54

Thermometry Precision

±0.18℉（±0.1℃）

Thermometry Speed

0.1s

Thermometry Range

(-4℉to 176℉/ -20℃to 80℃)

Thermometry Distance

<3cm

Display

2.7-inch e-ink screen with 264*176 resolution

RFID Card Reader

ID card/passport accessible（ISO1443A/B）

Wearing

With removable lanyard

Operating Temperature

(14℉to 122℉/ -10℃to 50℃)

Humidity

0%-95%RH (non condensing)

* Technical specifications of this product will change without further notice.

7. FAQ

7.1 How to change different wearing?

Smart Badge Scanner can be worn around neck or on the outside of the chest

pocket according to different scenarios. To switch between different wearing

ways, just attach or take off the removable lanyard.

7.2 Different light indicator and status

A flash of green light: successful scanning

Double flash of red light while touching: low battery

Light turns up to green for 1 second and then goes out: successful Bluetooth

connection

Light turns up to blue for 1 second and then goes out: Bluetooth

K18 Smart Badge Scanner User Manual

disconnection

Light turns up to red, green and blue in turn: reset

Double flash of yellow light: identifying bar code

7.3 Abnormal Bluetooth connection?

★If the green light (which indicates successful Bluetooth connection) does not

turn up after normal operation, scan barcode “Restore Bluetooth Name” and let

stand for 10 seconds and connect again after that.

Restore Bluetooth Name

★Scan bar code “Factory Reset” and Smart Badge Scanner will disconnect with

terminal devices. All functions have been set (e.g. scanning ways, Bluetooth

names and vibration) will be reset to factory settings.

Factory Reset

恢复出厂预设

8. Attention

1. Do not stare into scanning window;

2. Please scan in proper range of DOF;

3. Do not knock on or beat the product in order to avoid damage;

4. Please keep the balance of internal and external temperature of working

environment;

5. Scan at an angle while reading bar code for higher reading efficiency;

6. Do not expose the product to rain or water in order to avoid damage;

7. Do not use the product in high humidity environment.

Indice

Altri manuali Hyco Lettore di codici a barre

Hyco

Hyco W79LD Series Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente