Hypertherm Powermax45 XP Manuale di riferimento

Powermax45 XP®

RS-485 Serial Interface

Port

Powermax45 XP®

Port d’interface en série

RS-485

Field Service Bulletin

Bulletin de service sur le terrain

809930 | Revision 0 | March 2017

|Révision0|Mars2017

Hypertherm Inc.

Etna Road, P.O. Box 5010

Hanover, NH 03755 USA

603-643-3441 Tel (Main Office)

603-643-5352 Fax (All Departments)

[email protected] (Main Office Email)

800-643-9878 Tel (Technical Service)

[email protected] (Technical Service Email)

800-737-2978 Tel (Customer Service)

customer.ser[email protected] (Customer Service Email)

866-643-7711 Tel (Return Materials Authorization)

877-371-2876 Fax (Return Materials Authorization)

[email protected] (RMA email)

Hypertherm México, S.A. de C.V.

Avenida Toluca No. 444, Anexo 1,

Colonia Olivar de los Padres

Delegación Álvaro Obregón

México, D.F. C.P. 01780

52 55 5681 8109 Tel

52 55 5683 2127 Fax

Soporte.T[email protected] (Technical Service Email)

Hypertherm Plasmatechnik GmbH

Sophie-Scholl-Platz 5

63452 Hanau

Germany

00 800 33 24 97 37 Tel

00 800 49 73 73 29 Fax

31 (0) 165 596900 Tel (Technical Service)

00 800 4973 7843 Tel (Technical Service)

[email protected] (Technical Service Email)

Hypertherm (Singapore) Pte Ltd.

82 Genting Lane

Media Centre

Annexe Block #A01-01

Singapore 349567, Republic of Singapore

65 6841 2489 Tel

65 6841 2490 Fax

[email protected] (Marketing Email)

TechSupportAP[email protected] (Technical Service Email)

Hypertherm Japan Ltd.

Level 9, Edobori Center Building

2-1-1 Edobori, Nishi-ku

Osaka 550-0002 Japan

81 6 6225 1183 Tel

81 6 6225 1184 Fax

HT[email protected] (Main Office Email)

TechSupportAP[email protected] (Technical Service Email)

Hypertherm Europe B.V.

Vaartveld 9, 4704 SE

Roosendaal, Nederland

31 165 596907 Tel

31 165 596901 Fax

31 165 596908 Tel (Marketing)

31 (0) 165 596900 Tel (Technical Service)

00 800 4973 7843 Tel (Technical Service)

[email protected]

(Technical Service Email)

Hypertherm (Shanghai) Trading Co., Ltd.

B301, 495 ShangZhong Road

Shanghai, 200231

PR China

86-21-80231122 Tel

86-21-80231120 Fax

86-21-80231128 Tel (Technical Service)

[email protected]

(Technical Service Email)

South America & Central America: Hypertherm Brasil Ltda.

Rua Bras Cubas, 231 – Jardim Maia

Guarulhos, SP – Brasil

CEP 07115-030

55 11 2409 2636 Tel

[email protected] (Technical Service Email)

Hypertherm Korea Branch

#3904. APEC-ro 17. Heaundae-gu. Busan.

Korea 48060

82 (0)51 747 0358 Tel

82 (0)51 701 0358 Fax

[email protected] (Marketing Email)

TechSupportAP[email protected]

(Technical Service Email)

Hypertherm Pty Limited

GPO Box 4836

Sydney NSW 2001, Australia

61 (0) 437 606 995 Tel

61 7 3219 9010 Fax

[email protected] (Main Office Email)

TechSupportAP[email protected]

(Technical Service Email)

Hypertherm (India) Thermal Cutting Pvt. Ltd

A-18 / B-1 Extension,

Mohan Co-Operative Industrial Estate,

Mathura Road, New Delhi 110044, India

91-11-40521201/ 2/ 3 Tel

91-11 40521204 Fax

HTIndia.info@hypertherm.com (Main Office Email)

TechSupportAP[email protected]

(Technical Service Email)

1/28/16

Powermax and Hypertherm are trademarks of Hypertherm Inc. and may be registered in the United States and/or other countries. All other trademarks are the property of their

respective holders.

One of Hypertherm’s long-standing core values is a focus on minimizing our impact on the environment. Doing so is critical to our, and our customers’, success. We are

always striving to become better environmental stewards; it is a process we care deeply about.

Powermax et Hypertherm sont des marques d’Hypertherm Inc. qui peuvent être déposées aux États-Unis et/ou dans d’autres pays. Toutes les autres marques de commerce

sont la propriété de leurs détenteurs respectifs.

Une des valeurs fondamentales d’Hypertherm depuis toujours est l’accent mis sur la minimisation de notre impact sur l’environnement. Cet objectif est essentiel pour notre

réussite et celle de nos clients. Nous nous efforçons de devenir de meilleurs gestionnaires environnementaux, c’est une chose qui nous tient à cœur.

RS-485 Serial Interface Port

Powermax45 XP Field Service Bulletin 809930 3

Introduction

Purpose

This Field Service Bulletin describes the procedure for installing an RS-485 serial interface port.

Tools and materials needed

Assorted Phillips®and TORX®screwdrivers

428654 Kit contents

WARNING

ELECTRIC SHOCK CAN KILL

Disconnect electrical power before performing any maintenance.

All work requiring removal of the power supply cover must be performed

by a qualified technician.

See the Safety and Compliance Manual (80669C) provided with your

product for more safety precautions.

Part number Description Quantity

075418 Plastite #4 X 1/4 pan head screw 2

141109 RS-485 board 1

229765 RS-485 wire group 1

RS-485 Serial Interface Port

4809930 Field Service Bulletin Powermax45 XP

Figure 1 – RS-485 serial interface port with board and cables

Remove the power supply cover and component barrier

1. Set the power switch to OFF (O), disconnect the power cord from the power source, and

disconnect the gas supply.

2. Remove the 2 screws from the power supply handle . You may need to gently pull up on the

handle to remove the screws.

3. Gently tilt the tops of the front and rear panels away from the unit to pull the handle out.

1Rear panel connector cable

2Ground wire

3Screws for rear panel connector (2)

4RS-485 board

5Interface cable (J11)

RS-485 Serial Interface Port

Powermax45 XP Field Service Bulletin 809930 5

4. Slide the cover off.

5. Remove the 2 plastic pins that secure the component barrier to the main power board. Slide the

component barrier off.

RS-485 Serial Interface Port

6809930 Field Service Bulletin Powermax45 XP

Install the RS-485 serial interface port

1. Snap the RS-485 board into place on the center panel. Make sure the plastic tabs secure the

board.

2. From inside the rear panel, push out the rectangle marked by perforation on the rear panel label.

This exposes the mounting hole for the connector.

NOTICE

Do not route the ground wire and the longer cable from the RS-485 board below the fan. Doing

so can cause the wires to be pinched by the fan. If any wires get pinched behind the fan, this can

not only damage the wires but also prevent the fan from functioning correctly.

RS-485 Serial Interface Port

Powermax45 XP Field Service Bulletin 809930 7

3. Attach the ground wire ring terminal to the ground stud . Refer to the figure below. Tighten the

ground stud screw to 17.3 kg∙cm (15 inch·pounds).

Make sure all other ground wires remain connected to the ground stud.

Rotate the ground wire terminals on the stud so that each wire points in a

different direction.

4. Route the ground wire between the fan and the solenoid valve. Plug the quick-connect end of

the ground cable into the blade terminal on the RS-485 board .

5. Plug the short interface cable into J2 on the RS-485 board. Route the other end toward the

main power board. Run the cable through the plastic clip and the center panel pass-through

that is labeled “RS-485” . Plug it into J11 on the main power board.

6. Route the longer cable between the fan and the solenoid valve. Route one end of the cable

through the mounting hole in the rear panel. Plug the other end into J1 on the RS-485 board.

7. Attach the rear panel connector using 2 screws. Tighten the screws to 7 kg∙cm

(6 inch·pounds).

RS-485 Serial Interface Port

8809930 Field Service Bulletin Powermax45 XP

Install the component barrier and power supply cover

1. Make sure the ground clip is connected to the ground wire. The clip should be set in place to

accept the screw from the handle.

2. Make sure the component barrier is in place and secured to the main power board with 2 plastic

pins.

RS-485 Serial Interface Port

Powermax45 XP Field Service Bulletin 809930 9

3. Wrap the extended portion of the component barrier over the power cord connection points and

behind the gas hose or into the middle of the gas hose loop.

4. Slide the cover back on.

Make sure the louvers in the cover align with the fan.

Be careful not to pinch any wires.

5. Tilt the front and rear panels to reattach the handle. Position the handle over the holes in the top

of the cover, and position the ends of the handle underneath the edges of the panels.

6. Install the 2 screws that attach the cover and handle. Tighten to 23 kg∙cm (20 inch·pounds).

7. Reconnect the gas supply and the power cord.

RS-485 Serial Interface Port

10 809930 Field Service Bulletin Powermax45 XP

Altri manuali per Powermax45 XP

Indice

Lingue:

Altri manuali Hypertherm Sistema di saldatura

Hypertherm

Hypertherm Powermax 125 Manuale di riferimento

Hypertherm

Hypertherm H65 Manuale utente

Hypertherm

Hypertherm Powermax45 XP Manuale di riferimento

Hypertherm

Hypertherm powermax65 Manuale di riferimento

Hypertherm

Hypertherm Powermax45 XP Manuale di riferimento

Hypertherm

Hypertherm HT2000LHF Manuale utente

Hypertherm

Hypertherm Powermax105 Manuale utente

Hypertherm

Hypertherm Powermax 1000 Manuale di riferimento

Hypertherm

Hypertherm SYNC Powermax 65 Manuale utente

Hypertherm

Hypertherm HPRXD Series Guida

Hypertherm

Hypertherm Powermax1100 Manuale utente

Hypertherm

Hypertherm HT2000 Manuale di riferimento

Hypertherm

Hypertherm powermax600 Manuale utente

Hypertherm

Hypertherm powermax1250 Manuale utente

Hypertherm

Hypertherm Powermax45 XP Manuale di riferimento

Hypertherm

Hypertherm MAX42 Manuale utente

Hypertherm

Hypertherm powermax1650 Manuale utente

Hypertherm

Hypertherm powermax1000 Manuale utente

Hypertherm

Hypertherm HT40C Manuale utente

Hypertherm

Hypertherm POWERMAX 800 Manuale utente

Hypertherm

Hypertherm powermax600 Manuale utente

Hypertherm

Hypertherm MAXPRO200 Manuale utente

Hypertherm

Hypertherm HyPerformance Plasma HPR800XD Manuale di riferimento

Hypertherm

Hypertherm powermax65 Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente