Hystentel HST_IWN2000 Manuale utente
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
1
HYSENTELWireless Acess Point
HST_IWN2000
User Manual
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
2
Copyright © 2012 Shenzhen Haisheng Technology Co., Ltd
Copyright, All Rights Reserved
Without the written permission of Shenzhen Hysentel Co., Ltd,any unit or
individual shall not be allowed to imitation, replication, transcription or translation of
this book some or all of Commodity spread or used for any commercial, profit motive
is not in any form or by any means (electronic, mechanical, photocopying, recording,
or other possible means).
For Shenzhen Hysentel Co., Ltd.
registered trademarks. All other trademarks or registered trademarks mentioned in
this document are owned by their respective owners.
Product specifications and information referred to in this manual are for reference only,
if updates without notice. Unless a special agreement, this manual only as the use of
guidance in this manual all statements, information does not constitute a warranty of
any kind
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
3
目录
1. User manual Introduction......................................................................................................4
1.1. Premise......................................................................................................................4
1.2. outline........................................................................................................................4
2. product overview.......................................................................................................................4
2.1. product description....................................................................................................4
2.2. key features...............................................................................................................5
3. device intallation.......................................................................................................................5
3.1. Panel layout...............................................................................................................5
3.1.1. front panel .........................................................................................................5
3.1.2. back panel .........................................................................................................6
3.1.3. bottom panel......................................................................................................6
3.2. system requirements..................................................................................................6
3.3. installation enviroment..............................................................................................7
4. Configuration Guide .................................................................................................................7
4.1. Installation.................................................................................................................7
4.2. start and login............................................................................................................8
4.2.1. start....................................................................................................................8
4.2.2. login ..................................................................................................................8
4.3. Ethernet port configuration .......................................................................................8
4.3.1. WAN Port Configuration...................................................................................9
4.3.2. Ethernet Port VLAN........................................................................................10
4.3.3. PSE Configuration ..........................................................................................11
4.4. wireless configuration.............................................................................................11
4.4.1. Wireless Physical ............................................................................................12
4.4.2. VAP.................................................................................................................13
4.5. system information..................................................................................................14
4.5.1. Overview.........................................................................................................15
4.5.2. Available Channel...........................................................................................15
4.5.3. Update.............................................................................................................16
4.5.4. Safe..................................................................................................................16
4.5.5. Restart .............................................................................................................17
4.5.6. Factory Settings...............................................................................................17
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
4
1. User manual Introduction
Before you are ready to install and use this product, please carefully read this manual to fully use
all the features of this product.
1.1.Premise
Wireless access point referred to in this manual, such as no special instructions, refer
to HST_IWN2000 wireless access point, referred to below as HST_IWN2000 wireless
access. The picture used in this manual are equipped with the relevant parameters,
the actual product configuration interface does not provide, according to the actual
need to set these parameters.
Schematic network diagram shown in this manual only for description purposes, the
original product may vary, please refer to product physical map.
1.2.outline
Chapter 1: Introduction to the user manual.
Chapter 2: Product Overview. Brief wireless access functions and features.
Chapter 3: Hardware installation. Help you with the hardware installation of the wireless access
device.
Chapter 4: Configuration Guide. Help you configure the wireless access advanced features.
2. product overview
2.1.product description
The product HST_IWN2000 Shenzhen Hysentel Technology Co., Ltd. is designed
for hotels, shopping malls, indoor wireless coverage project wireless access products,
and provides a standard wireless access functionality to support wireless access to a
variety of countries, can create up to4 wireless access points, for hotels, guest houses,
villas, residential and other needs high-end wireless coverage area, in addition to the
wireless access also supports VLAN access, voice and data transport optimization,
the PSE output, and a wealth of features to facilitatethe formation of the network of
safe, high-speed and easy to manage.
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
5
2.2.key features
3. device intallation
3.1.Panel layout
3.1.1. front panel
PSE： PSE function led indicator
Power：Power led indicator
WAN：wan led indicator
LAN2：PSE Ethernet port led indicator
LAN1：Ethernet port 1 led indicator
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
6
3.1.2. back panel
Manager Port：Manager Ethernet port
Phone ：Analog phone interface
3.1.3. bottom panel
Internet：Internet Ethernet Port
Eth/PSE：PSE Port
Phone：analog phone port
3.2.system requirements
802.3af PSE device
Internet service
Pc with wireless 802.11b/g/n card
CAT5 cable
Internet Explorer
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
7
3.3.installation enviroment
802.3AF PSE power supply
wireless access in a dry and ventilated environment
Avoid wireless access point on the wet such as the environment is not
conducive to the use of electrical equipment
Use temperature should be between 0 º C to 40 º C
Humidity should be in the case of 5%% the 90RH no condensation
4. Configuration Guide
4.1.Installation
HST_IWN2000 Network diagram
internet
HST
_
IWN2000
switch
PC
HST
_
IWN2000
firewall
ethernet
wireless
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
8
1,Reference on the figure
2, Connect the computer to the Ethernet port of the wireless access
3, Modify the configuration and save, reboot
4,connect to poe switch
Note: the initial IP192.168.200.1 of wireless access, the subnet mask of 255.255.255.0
4.2.start and login
4.2.1. start
input Address in the browser address bar enter the wireless access of a computer to connect to
a wireless access (default is 192.168.200.1).
4.2.2. login
After successfully connected to the wireless access device, will come to the login page.
1, Please enter your user name and password in the User and Password input box
2, Click Submit, sending login request
3, If you enter the correct user name and password, successfully configured home page, or
would have been stopped at the login page.
The default user name and password: admin / admin, if you have forgotten your user name or
password is configured, use the reference to restore the factory settings related to a single, strongly
recommend that you first login to modify the default user name and password.
Figure 1 login page
4.3.Ethernet port configuration
When you choose the Configure menu under the Function Menu panel Ethernet WAN Port
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
9
Configuration, Ethernet the Port VLANs, the PSE Configuration three sub-menu will appear ,
click the function you need the sub-menu.
The following detailed description of the usefulness and the preparation of its various
sub-menus.
图表 1 网口配置菜单
4.3.1. WAN Port Configuration
Configure the wireless access device IP, subnet mask, default gateway and mode of
administration.
IPAddress IPaddress
Netmask subnetmask
Default gateway default gateway
Manager Mode manage mod
Standard: Standard mode, said wireless access to work independently, and
does not control home server, the default option.
Client: Client mode, when you select this mode must be selected in the
Manager Server Address bar fill in the AP Manager Server's IP address, as
shown in Figure 4.
Manager Server Address
figure 3 of the standard mode
深圳海盛特科技有限公司
Shenzhen Hysentel Technology Co., Ltd.
10
figure 4 client mode
figure 2 Modified successfully, need to restart
Modify the configuration, click the Save button, if you modify successful, a prompt appears.
Prompted, click Restart to restart the wireless access, the new configuration to take effect.
When the wireless access device reboot is complete, re-login to the system for you
automatically.
As you operate the wireless access, and can change the network connection or a network
status, so when you are unable to automatically log on to the wireless access device, the network
is restored, manually re-login the wireless access device.
4.3.2. Ethernet Port VLAN
Modify Ethernet ports VLAN.。
figure 3 Ethernet Port VLAN configuration
If you want to enable the VLAN function in a network port, please check the appropriate
option, then in the appropriate input box you have configured VLAN ID, as shown in Figure 6,
Indice
