I-MO I3H Series Manuale utente

DBI21-80H3I

__________________________________________________________________________________________________________________________________________________

0102/21/5 Page 1 of 5

INTRODUCTION

i3H provides:



Powerful Standard Features in one unit including

Controller

Network

Operator Interface

Highly Visual Display Screen

Standard Features on i3H

Base

Model

Network Screen Type Standard

Features

i3H08

On-Board

Ethernet

100BaseT

8.4” TFT SVGA

with 32,768

colors

CompactFlash

3 Serial Ports

Ethernet

i3H10 10.4” TFT

SVGA

with 32,768

colors

i3H12 12.1” TFT

SVGA

with 32,768

colors

2 Specifications/ Product Descriptions

Table 2 – i3H Base Specifications

Base Models i3H08

(8-inch) (SVGA)

i3H10

10-inch) (SVGA)

i3H12

(12-inch) (SVGA)

Display Type

(LCD with

backlight)

800 x 600

TFT

800 x 600

TFT

800 x 600

TFT

Display Size 8.4” 10.4” 12.1”

Display Screen

Dimensions

6.7”W x 5”H

(170 x 128 mm)

8.3“W x 6.2“H

(211 x 159 mm)

9.7“W x 7.3“H

(246 x 185 mm)

Display Memory 8 MBytes

User Keys 7 configurable keys + System Key

Screens

Supported

1,023 screens

(300 objects per screen)

Number of

Colors

32,768

3 INSTALLATION

Base

Models

i3H08

(8-inch)

i3H10

10-inch)

i3H12

(12-inch)

Primary

Power

Voltage:

24 VDC (+/-10%)

Steady State

Current:

0.625 A @ 24 VDC

Inrush Current:

(25 A @ 24 VDC)

for 0.7 ms

Voltage:

24 VDC (+/-10%)

Steady State

Current:

1.25 A @ 24 VDC

Inrush Current:

(30 A @ 24 VDC)

for 1 ms

Voltage:

24 VDC (+/-10%)

Steady State Current:

1.25 A @ 24 VDC

Inrush Current:

(30 A @ 24 VDC)

for 1 ms

i3H Dimensions

See Panel Cut-outs and Dimensionsfor complete details (Section 3.2)

Base

Models

i3H08

(8-inch)

i3H10

10-inch)

i3H12

(12-inch)

Height 7.0” (178 mm) 9.09” (230.9 mm) 10.25” (260.4 mm)

Width 9.17” (233 mm) 11.95” (303.5 mm) 12.87” (326.9 mm)

Mounting

Depth

2.35” (59.70 mm) 2.52” (64 mm) 2.52” (64 mm)

Keypad

Material

Faceplate made of LexanHP92 by GE Plastics.

The material is resistant to most corrosive substances found in

industrial environments. The material also holds up well in most

industrial conditions.

Serial Ports 3RS-232 / RS-485 Ports. Software Selectable.

Network

Options

On-board Ethernet 100BaseT

Control

Memory

256K Ladder Memory plus 32KB Register Space

Control

Scan Rate

0.2mS / K Ladder Logic (typical)

Portable

Memory

Compact FLASH (CF) slot

Temperature

& Humidity

32 - 122°F (0 - 50°C), 5 to 95% Non-condensing

UL Please contact IMO for certificate information

i3H Series Models:

i3H08/00000-SEOL - 8

”

display model

i3H10/00000-SEOL - 10

”

display model

i3H12/00000-SEOL - 12

”

display model

Note: Prior to mounting, observe requirements for the panel layout design and adequate clearances in the I3 Hardware Manual. A handy checklist is provided in the Installation

chapter.

3.1 Installation Procedures

a. i3H Base Installation

1. Per specifications of the I3H model you are using, carefully prepare the panel cutout. Make sure the corners of the cutout are square andfree from burrs.

(Locate the panel

cut-outs and dimensionsthat pertain to your I3H model as shown in this document.)

2. Cut the host panel

3. Insert the i3H (base unit only) through the panel cutout from the front. The gasket material needs to lie between the host panel and the I3H.

4. Install and tighten the mounting clips (provided with the I3H) until the gasket material forms a tight seal.

5. Connect cables as needed such as communications, programming, power and fiber optic cables to the I3H ports using the provided connectors.

6. As a final step before using, carefully remove the protect

ive, plastic sheet from the front of the unit. The protective, transparent sheet is used to protect the display window.

7. Begin configuration procedures for the I3H.

Caution: Do not force the I3H into the panel cutout. An incorrectly sized panel cutout damages the I3H screen.

Caution: Do not over-tighten. Over-tightening damages the case.

I3H08-12IBD Specifications / Installation

__________________________________________________________________________________________________________________________________________________

5/12/2010 Page 2 of 5

3.2 Panel Cut-Out and Dimensions

3.2.1 i3H08 (8-inch)

3.2.2 i3H10 (10-inch)

3.2.2 i3H12 (12-inch)

Figure 2 – Panel Cut-out and Dimensions 8-inch

I3H Panel Cut-Out 9.17"

(233.0 mm)

2.35"

(59.70 mm)

i3H

I3H Side View

I3H Rear View

8.69 [220.7mm]

6.53 [165.9mm]

Figure 4 – Panel Cut-out and Dimensions 12-inch

I3H Panel Cut-Out

2.52”

(64 mm)

i3H

I3H Side View

I3H Rear View

12.87"

(326.9mm)

12.29 [312.0mm]

9.66 [245.4mm]

Figure 3– Panel Cut-out and Dimensions 10-inch

11.95

(303.5 mm)

2.52

(64 mm)

i3H

I3H

I3H Side View

I3H Rear View

I3H Panel Cut-Out

8.505

(216.0 mm)

11.360

(288.5 mm)

I3H08-12IBD

__________________________________________________________________________________________________________________________________________________

5/12/2010 Page 3 of 5

3.3 i3H Base Ports and Connectors

3.3.1 Primary Power Port / Grounding

a. Port 1 (MJ1) / Port 2 (MJ2) Modular Jacks

Figure 6 – Close-up of Port 1 (MJ1) / Port 2 (MJ2) (RS-232 and RS-485)

The I3H base has power, network, programming and fiber optic ports. Three RS-232 and RS-485 ports are available. (Default programming port is MJ1)

Parallel

Port

Port 2Port 3 Port 1LAN

Primary Power

Connector

001QX005

Parallel

Port

Port 2

CN1

Port 1

Parallel

Port

Port 2Port 3 Port 1LAN

Primary Power

Connector

001QX006

3H10

10”

3H08

8”

3H12

12”

Port 3

MJ1 MJ2

MJ1

MJ1 MJ2

MJ2

CN1 CN1

Primary Power

Connector

Figure 5 – I3H Base Ports and Connectors

Table 4 – Primary Power Port Pins

Signal Pin Description

V+ Input power supply voltage

V- Input power supply ground

Frame Ground

Note: Power Supply Voltage Range is from 24VDC ±

±±

±10%.

3.3.2 RS-232 Port / RS-485 Port

There are a variety of ways to connect to the RS-232 and RS-485 ports; You can use

two modular jacks (MJ1 and MJ2) or the 25-pin Dsub connector (CN1).

Table 5 – Ports and Functions (Port 1, 2, and 3)

Functions Port 1 (MJ1)

Port 2 (MJ2) Port 3 (CN1)

RS-232 2

RS-485 2

Hardware Handshaking 2

Programming 2

Ladder Function

Controlled 2

Modem 2

2* 2

* Not supported by i3 Config Modem Function Blocks

1 2 3 4 5 6

Table 6 – Port 1 (MJ1) / Port 2

(MJ2) Pins

Pin Signal

1 +SD/RD

2 -SD/RD

3 +5V

4 +5V

5 0V

6 0V

7 RXD

8 TXD

Output power supply: Max.

150mA

Figure 7 – Port 3 (CN1) RS-232 / RS-485 Connector

b. Port 3 (CN1) Connector

Table 7– Port 3 (CN1) Pins

Pin # Signal Pin # Signal

1 FG 14 I3H451, 551, 651: +RTS

2 TXD 15 Not Used

3 RXD 16 Not Used

4 RTS 17 I3H451, 551, 651: -RTS

5 CTS 18 -CTS

6 Not Used 19 +CTS

7 SG 20 Not Used

8 Not Used 21 Not Used

9 +5V 22 Not Used

10 0V 23 Not Used

11 Not Used 24 +RD

12 +SD 25 -RD

13 -SD

3.3.3 DIP-Switch

The DIP switch is used for setting the terminating resistance of the RS-485 signal line at the CN1,

MJ1, or MJ2 connector.

Figure 7 – DIP Switch

(1)

Set DIPSW 8 to ON position when termination is required on MJ2.

(2)

Set DIPSW 7 at the terminating station of the i3H units to the ON position when

connecting PLCs through RS-422/485.

(3)

Set DIPSW 6 to ON position when termination is required on MJ1.

I3H08-12IBD Specifications / Installation

__________________________________________________________________________________________________________________________________________________

5/12/2010 Page 4 of 5

Figure 8 - Port 3 (CN1) RS-232 Port

Figure 9 – Port 3 (CN1) RS-485 Port

Shielded Cable

Receive Data

Send Data

To RS-232 Port

SG 7

CS 5

Port 3

RS 4

RD 3

SD 2

FG 1

Signal Pin No.

Shielded Cable

Send Data (-)

To RS-485 Port

Send Data (+)

Receive Data (-)

Receive Data (+)

SG 7

-SD 13

Port 3

+SD 12

-RD 25

+RD 24

FG 1

Signal Pin No.

3.5 Quick Start Instructions

1. Download i3 Configurator V9.0 (or better) from the IMO website and install, following on-screen instructions.

2. Connect a suitable 24Vdc supply to the screw terminals as shown in Figure 5, and power up.

Serial Programming:

Requirements: i3-PC45 programming cable (optional part: PC501 - USB to

Serial Converter for PC’s without serial port), PC with Windows XP or better.

1. Connect the RJ45 connector of the i3-PC45 cable to the i3H port

MJ1 and connect the 9-pin D-type connector to the PC and open

i3 Configurator.

2. Select Tools->Application Settings->Communications-

>Configure->Com Port (or USB if convertor used). Input the

required com port number then press OK.

3. If the connection is successful, then the status of the i3 should no

longer be grayed out and display as shown .

4. To get started with the programming download the i3 Basic

Tutorial from the IMO website.

Ethernet Programming:

Requirements: Ethernet cross-over patch cable, PC with Windows XP or better.

1. Set up the PC to have a fixed IP and Subnet of 192.168.254.1/

255.255.255.0 (for in-depth instruction on how to do this please

download the i3 Ethernet tutorial.pdf).

2. Connect the RJ45 connector of the patch cable to the i3H LAN port

and to the PC LAN port and open i3 Configurator.

3. Select Tools->Application Settings->Communications->Configure-

>Ethernet. Then enter IP address 192.168.254.128, select mode

iNX/i3Ce then press OK.

4. If the connection is successful, then the status of the i3 should no

longer be grayed out and display as shown .

5. To get started with the programming download the i3 Basic Tutorial

from the IMO website.

I3H08-12IBD Specifications / Installation

_______________________________________________________________________________________________________________________________________________

5/12/2010 Page 5 of 5

4 Safety

5 Technical support

Warning: Consult

user documentation.

Warning: Electric

Shock hazard

When found on the product, the following symbols specify:

WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I, Division 2

AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIAL INACCEPTABLE POUR LES EMPLACEMENTS DE

CLASSE 1, DIVISION 2.

WARNING - The USB parts are for operational maintenance only. Do not leave permanently connected unless area is known to be non-hazardous.

WARNING – EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS

AVERTISSEMENT - RISQUE D'EXPLOSION - AFIN D'EVITER TOUT RISQUE D'EXPLOSION, S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX

AVANT DE CHANGER LA BATTERIE

WARNING - Battery May Explode If Mistreated. Do Not Recharge, Disassemble or Dispose Of In Fire

WARNING: Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved s

hould install, adjust, operate, or service

this equipment. Read and understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe

bodily injury or loss of life.

For detailed installation and a handy checklist that covers panel box layout requirements and minimum clearances, refer to the hardware manual.

•All applicable codes and standards need to be followed in the installation of this product.

Adhere to the following safety precautions whenever any type of connection is made to the module.

•Connect the green safety (earth) ground first before making any other connections.

•When connecting to electric circuits or pulse-initiating equipment, open their related breakers. Do not make connections to live power lines.

•Make connections to the module first; then connect to the circuit to be monitored.

•Route power wires in a safe manner in accordance with good practice and local codes.

•Wear proper personal protective equipment including safety glasses and insulated gloves when making connections to power circuits.

•Ensure floor, hands and shoes are dry before making any connection to a power line.

•Make sure the unit is turned OFF before making connection to terminals. Make sure all circuits are de-energized before making connections.

•Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately if defective.

Please contact automation@imopc.com

For further technical information and a full specification,

please consult the Hardware Manual

IMO Precision Controls Ltd

1000 North Circular Rd, Staples Corner, London. NW2 7JP

Tel: +44 (0) 208 452 6444,

Fax: +44 (0) 208 450 2274,

Web: www.imopc.com

Questo manuale è adatto per i seguenti modelli

Altri manuali i-MO Monitor

i-MO

i-MO AT-7 Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

i-MO i3H Series Manuale utente

Manuali Monitor popolari di altre marche